Re: [v2] wifi: iwlegacy: Clear stale interrupts before resuming device

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Ville Syrjala <ville.syrjala@xxxxxxxxxxxxxxx> wrote:

> From: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
> 
> iwl4965 fails upon resume from hibernation on my laptop. The reason
> seems to be a stale interrupt which isn't being cleared out before
> interrupts are enabled. We end up with a race beween the resume
> trying to bring things back up, and the restart work (queued form
> the interrupt handler) trying to bring things down. Eventually
> the whole thing blows up.
> 
> Fix the problem by clearing out any stale interrupts before
> interrupts get enabled during resume.
> 
> Here's a debug log of the indicent:
> [   12.042589] ieee80211 phy0: il_isr ISR inta 0x00000080, enabled 0xaa00008b, fh 0x00000000
> [   12.042625] ieee80211 phy0: il4965_irq_tasklet inta 0x00000080, enabled 0x00000000, fh 0x00000000
> [   12.042651] iwl4965 0000:10:00.0: RF_KILL bit toggled to enable radio.
> [   12.042653] iwl4965 0000:10:00.0: On demand firmware reload
> [   12.042690] ieee80211 phy0: il4965_irq_tasklet End inta 0x00000000, enabled 0xaa00008b, fh 0x00000000, flags 0x00000282
> [   12.052207] ieee80211 phy0: il4965_mac_start enter
> [   12.052212] ieee80211 phy0: il_prep_station Add STA to driver ID 31: ff:ff:ff:ff:ff:ff
> [   12.052244] ieee80211 phy0: il4965_set_hw_ready hardware  ready
> [   12.052324] ieee80211 phy0: il_apm_init Init card's basic functions
> [   12.052348] ieee80211 phy0: il_apm_init L1 Enabled; Disabling L0S
> [   12.055727] ieee80211 phy0: il4965_load_bsm Begin load bsm
> [   12.056140] ieee80211 phy0: il4965_verify_bsm Begin verify bsm
> [   12.058642] ieee80211 phy0: il4965_verify_bsm BSM bootstrap uCode image OK
> [   12.058721] ieee80211 phy0: il4965_load_bsm BSM write complete, poll 1 iterations
> [   12.058734] ieee80211 phy0: __il4965_up iwl4965 is coming up
> [   12.058737] ieee80211 phy0: il4965_mac_start Start UP work done.
> [   12.058757] ieee80211 phy0: __il4965_down iwl4965 is going down
> [   12.058761] ieee80211 phy0: il_scan_cancel_timeout Scan cancel timeout
> [   12.058762] ieee80211 phy0: il_do_scan_abort Not performing scan to abort
> [   12.058765] ieee80211 phy0: il_clear_ucode_stations Clearing ucode stations in driver
> [   12.058767] ieee80211 phy0: il_clear_ucode_stations No active stations found to be cleared
> [   12.058819] ieee80211 phy0: _il_apm_stop Stop card, put in low power state
> [   12.058827] ieee80211 phy0: _il_apm_stop_master stop master
> [   12.058864] ieee80211 phy0: il4965_clear_free_frames 0 frames on pre-allocated heap on clear.
> [   12.058869] ieee80211 phy0: Hardware restart was requested
> [   16.132299] iwl4965 0000:10:00.0: START_ALIVE timeout after 4000ms.
> [   16.132303] ------------[ cut here ]------------
> [   16.132304] Hardware became unavailable upon resume. This could be a software issue prior to suspend or a hardware issue.
> [   16.132338] WARNING: CPU: 0 PID: 181 at net/mac80211/util.c:1826 ieee80211_reconfig+0x8f/0x14b0 [mac80211]
> [   16.132390] Modules linked in: ctr ccm sch_fq_codel xt_tcpudp xt_multiport xt_state iptable_filter iptable_nat nf_nat nf_conntrack nf_defrag_ipv4 ip_tables x_tables binfmt_misc joydev mousedev btusb btrtl btintel btbcm bluetooth ecdh_generic ecc iTCO_wdt i2c_dev iwl4965 iwlegacy coretemp snd_hda_codec_analog pcspkr psmouse mac80211 snd_hda_codec_generic libarc4 sdhci_pci cqhci sha256_generic sdhci libsha256 firewire_ohci snd_hda_intel snd_intel_dspcfg mmc_core snd_hda_codec snd_hwdep firewire_core led_class iosf_mbi snd_hda_core uhci_hcd lpc_ich crc_itu_t cfg80211 ehci_pci ehci_hcd snd_pcm usbcore mfd_core rfkill snd_timer snd usb_common soundcore video parport_pc parport intel_agp wmi intel_gtt backlight e1000e agpgart evdev
> [   16.132456] CPU: 0 UID: 0 PID: 181 Comm: kworker/u8:6 Not tainted 6.11.0-cl+ #143
> [   16.132460] Hardware name: Hewlett-Packard HP Compaq 6910p/30BE, BIOS 68MCU Ver. F.19 07/06/2010
> [   16.132463] Workqueue: async async_run_entry_fn
> [   16.132469] RIP: 0010:ieee80211_reconfig+0x8f/0x14b0 [mac80211]
> [   16.132501] Code: da 02 00 00 c6 83 ad 05 00 00 00 48 89 df e8 98 1b fc ff 85 c0 41 89 c7 0f 84 e9 02 00 00 48 c7 c7 a0 e6 48 a0 e8 d1 77 c4 e0 <0f> 0b eb 2d 84 c0 0f 85 8b 01 00 00 c6 87 ad 05 00 00 00 e8 69 1b
> [   16.132504] RSP: 0018:ffffc9000029fcf0 EFLAGS: 00010282
> [   16.132507] RAX: 0000000000000000 RBX: ffff8880072008e0 RCX: 0000000000000001
> [   16.132509] RDX: ffffffff81f21a18 RSI: 0000000000000086 RDI: 0000000000000001
> [   16.132510] RBP: ffff8880072003c0 R08: 0000000000000000 R09: 0000000000000003
> [   16.132512] R10: 0000000000000000 R11: ffff88807e5b0000 R12: 0000000000000001
> [   16.132514] R13: 0000000000000000 R14: 0000000000000000 R15: 00000000ffffff92
> [   16.132515] FS:  0000000000000000(0000) GS:ffff88807c200000(0000) knlGS:0000000000000000
> [   16.132517] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
> [   16.132519] CR2: 000055dd43786c08 CR3: 000000000978f000 CR4: 00000000000006f0
> [   16.132521] Call Trace:
> [   16.132525]  <TASK>
> [   16.132526]  ? __warn+0x77/0x120
> [   16.132532]  ? ieee80211_reconfig+0x8f/0x14b0 [mac80211]
> [   16.132564]  ? report_bug+0x15c/0x190
> [   16.132568]  ? handle_bug+0x36/0x70
> [   16.132571]  ? exc_invalid_op+0x13/0x60
> [   16.132573]  ? asm_exc_invalid_op+0x16/0x20
> [   16.132579]  ? ieee80211_reconfig+0x8f/0x14b0 [mac80211]
> [   16.132611]  ? snd_hdac_bus_init_cmd_io+0x24/0x200 [snd_hda_core]
> [   16.132617]  ? pick_eevdf+0x133/0x1c0
> [   16.132622]  ? check_preempt_wakeup_fair+0x70/0x90
> [   16.132626]  ? wakeup_preempt+0x4a/0x60
> [   16.132628]  ? ttwu_do_activate.isra.0+0x5a/0x190
> [   16.132632]  wiphy_resume+0x79/0x1a0 [cfg80211]
> [   16.132675]  ? wiphy_suspend+0x2a0/0x2a0 [cfg80211]
> [   16.132697]  dpm_run_callback+0x75/0x1b0
> [   16.132703]  device_resume+0x97/0x200
> [   16.132707]  async_resume+0x14/0x20
> [   16.132711]  async_run_entry_fn+0x1b/0xa0
> [   16.132714]  process_one_work+0x13d/0x350
> [   16.132718]  worker_thread+0x2be/0x3d0
> [   16.132722]  ? cancel_delayed_work_sync+0x70/0x70
> [   16.132725]  kthread+0xc0/0xf0
> [   16.132729]  ? kthread_park+0x80/0x80
> [   16.132732]  ret_from_fork+0x28/0x40
> [   16.132735]  ? kthread_park+0x80/0x80
> [   16.132738]  ret_from_fork_asm+0x11/0x20
> [   16.132741]  </TASK>
> [   16.132742] ---[ end trace 0000000000000000 ]---
> [   16.132930] ------------[ cut here ]------------
> [   16.132932] WARNING: CPU: 0 PID: 181 at net/mac80211/driver-ops.c:41 drv_stop+0xe7/0xf0 [mac80211]
> [   16.132957] Modules linked in: ctr ccm sch_fq_codel xt_tcpudp xt_multiport xt_state iptable_filter iptable_nat nf_nat nf_conntrack nf_defrag_ipv4 ip_tables x_tables binfmt_misc joydev mousedev btusb btrtl btintel btbcm bluetooth ecdh_generic ecc iTCO_wdt i2c_dev iwl4965 iwlegacy coretemp snd_hda_codec_analog pcspkr psmouse mac80211 snd_hda_codec_generic libarc4 sdhci_pci cqhci sha256_generic sdhci libsha256 firewire_ohci snd_hda_intel snd_intel_dspcfg mmc_core snd_hda_codec snd_hwdep firewire_core led_class iosf_mbi snd_hda_core uhci_hcd lpc_ich crc_itu_t cfg80211 ehci_pci ehci_hcd snd_pcm usbcore mfd_core rfkill snd_timer snd usb_common soundcore video parport_pc parport intel_agp wmi intel_gtt backlight e1000e agpgart evdev
> [   16.133014] CPU: 0 UID: 0 PID: 181 Comm: kworker/u8:6 Tainted: G        W          6.11.0-cl+ #143
> [   16.133018] Tainted: [W]=WARN
> [   16.133019] Hardware name: Hewlett-Packard HP Compaq 6910p/30BE, BIOS 68MCU Ver. F.19 07/06/2010
> [   16.133021] Workqueue: async async_run_entry_fn
> [   16.133025] RIP: 0010:drv_stop+0xe7/0xf0 [mac80211]
> [   16.133048] Code: 48 85 c0 74 0e 48 8b 78 08 89 ea 48 89 de e8 e0 87 04 00 65 ff 0d d1 de c4 5f 0f 85 42 ff ff ff e8 be 52 c2 e0 e9 38 ff ff ff <0f> 0b 5b 5d c3 0f 1f 40 00 41 54 49 89 fc 55 53 48 89 f3 2e 2e 2e
> [   16.133050] RSP: 0018:ffffc9000029fc50 EFLAGS: 00010246
> [   16.133053] RAX: 0000000000000000 RBX: ffff8880072008e0 RCX: ffff88800377f6c0
> [   16.133054] RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff8880072008e0
> [   16.133056] RBP: 0000000000000000 R08: ffffffff81f238d8 R09: 0000000000000000
> [   16.133058] R10: ffff8880080520f0 R11: 0000000000000000 R12: ffff888008051c60
> [   16.133060] R13: ffff8880072008e0 R14: 0000000000000000 R15: ffff8880072011d8
> [   16.133061] FS:  0000000000000000(0000) GS:ffff88807c200000(0000) knlGS:0000000000000000
> [   16.133063] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
> [   16.133065] CR2: 000055dd43786c08 CR3: 000000000978f000 CR4: 00000000000006f0
> [   16.133067] Call Trace:
> [   16.133069]  <TASK>
> [   16.133070]  ? __warn+0x77/0x120
> [   16.133075]  ? drv_stop+0xe7/0xf0 [mac80211]
> [   16.133098]  ? report_bug+0x15c/0x190
> [   16.133100]  ? handle_bug+0x36/0x70
> [   16.133103]  ? exc_invalid_op+0x13/0x60
> [   16.133105]  ? asm_exc_invalid_op+0x16/0x20
> [   16.133109]  ? drv_stop+0xe7/0xf0 [mac80211]
> [   16.133132]  ieee80211_do_stop+0x55a/0x810 [mac80211]
> [   16.133161]  ? fq_codel_reset+0xa5/0xc0 [sch_fq_codel]
> [   16.133164]  ieee80211_stop+0x4f/0x180 [mac80211]
> [   16.133192]  __dev_close_many+0xa2/0x120
> [   16.133195]  dev_close_many+0x90/0x150
> [   16.133198]  dev_close+0x5d/0x80
> [   16.133200]  cfg80211_shutdown_all_interfaces+0x40/0xe0 [cfg80211]
> [   16.133223]  wiphy_resume+0xb2/0x1a0 [cfg80211]
> [   16.133247]  ? wiphy_suspend+0x2a0/0x2a0 [cfg80211]
> [   16.133269]  dpm_run_callback+0x75/0x1b0
> [   16.133273]  device_resume+0x97/0x200
> [   16.133277]  async_resume+0x14/0x20
> [   16.133280]  async_run_entry_fn+0x1b/0xa0
> [   16.133283]  process_one_work+0x13d/0x350
> [   16.133287]  worker_thread+0x2be/0x3d0
> [   16.133290]  ? cancel_delayed_work_sync+0x70/0x70
> [   16.133294]  kthread+0xc0/0xf0
> [   16.133296]  ? kthread_park+0x80/0x80
> [   16.133299]  ret_from_fork+0x28/0x40
> [   16.133302]  ? kthread_park+0x80/0x80
> [   16.133304]  ret_from_fork_asm+0x11/0x20
> [   16.133307]  </TASK>
> [   16.133308] ---[ end trace 0000000000000000 ]---
> [   16.133335] ieee80211 phy0: PM: dpm_run_callback(): wiphy_resume [cfg80211] returns -110
> [   16.133360] ieee80211 phy0: PM: failed to restore async: error -110
> 
> Cc: stable@xxxxxxxxxxxxxxx
> Cc: Stanislaw Gruszka <stf_xl@xxxxx>
> Cc: Kalle Valo <kvalo@xxxxxxxxxx>
> Cc: linux-wireless@xxxxxxxxxxxxxxx
> Signed-off-by: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
> Acked-by: Stanislaw Gruszka <stf_xl@xxxxx>

Patch applied to wireless.git, thanks.

07c90acb071b wifi: iwlegacy: Clear stale interrupts before resuming device

-- 
https://patchwork.kernel.org/project/linux-wireless/patch/20241001200745.8276-1-ville.syrjala@xxxxxxxxxxxxxxx/

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches





[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux