6.11-stable review patch. If anyone has any objections, please let me know.
------------------
From: Kimriver Liu <kimriver.liu@xxxxxxxxxxxx>
commit 5d69d5a00f80488ddcb4dee7d1374a0709398178 upstream.
It was observed that issuing the ABORT bit (IC_ENABLE[1]) will not
work when IC_ENABLE is already disabled.
Check if the ENABLE bit (IC_ENABLE[0]) is disabled when the controller
is holding SCL low. If the ENABLE bit is disabled, the software needs
to enable it before trying to issue the ABORT bit. otherwise,
the controller ignores any write to ABORT bit.
These kernel logs show up whenever an I2C transaction is
attempted after this failure.
i2c_designware e95e0000.i2c: timeout waiting for bus ready
i2c_designware e95e0000.i2c: timeout in disabling adapter
The patch fixes the issue where the controller cannot be disabled
while SCL is held low if the ENABLE bit is already disabled.
Fixes: 2409205acd3c ("i2c: designware: fix __i2c_dw_disable() in case master is holding SCL low")
Signed-off-by: Kimriver Liu <kimriver.liu@xxxxxxxxxxxx>
Cc: <stable@xxxxxxxxxxxxxxx> # v6.6+
Reviewed-by: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx>
Acked-by: Jarkko Nikula <jarkko.nikula@xxxxxxxxxxxxxxx>
Reviewed-by: Andy Shevchenko <andy@xxxxxxxxxx>
Signed-off-by: Andi Shyti <andi.shyti@xxxxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
drivers/i2c/busses/i2c-designware-common.c | 14 ++++++++++
drivers/i2c/busses/i2c-designware-core.h | 1
drivers/i2c/busses/i2c-designware-master.c | 38 +++++++++++++++++++++++++++++
3 files changed, 53 insertions(+)
--- a/drivers/i2c/busses/i2c-designware-common.c
+++ b/drivers/i2c/busses/i2c-designware-common.c
@@ -441,6 +441,7 @@ err_release_lock:
void __i2c_dw_disable(struct dw_i2c_dev *dev)
{
+ struct i2c_timings *t = &dev->timings;
unsigned int raw_intr_stats;
unsigned int enable;
int timeout = 100;
@@ -453,6 +454,19 @@ void __i2c_dw_disable(struct dw_i2c_dev
abort_needed = raw_intr_stats & DW_IC_INTR_MST_ON_HOLD;
if (abort_needed) {
+ if (!(enable & DW_IC_ENABLE_ENABLE)) {
+ regmap_write(dev->map, DW_IC_ENABLE, DW_IC_ENABLE_ENABLE);
+ /*
+ * Wait 10 times the signaling period of the highest I2C
+ * transfer supported by the driver (for 400KHz this is
+ * 25us) to ensure the I2C ENABLE bit is already set
+ * as described in the DesignWare I2C databook.
+ */
+ fsleep(DIV_ROUND_CLOSEST_ULL(10 * MICRO, t->bus_freq_hz));
+ /* Set ENABLE bit before setting ABORT */
+ enable |= DW_IC_ENABLE_ENABLE;
+ }
+
regmap_write(dev->map, DW_IC_ENABLE, enable | DW_IC_ENABLE_ABORT);
ret = regmap_read_poll_timeout(dev->map, DW_IC_ENABLE, enable,
!(enable & DW_IC_ENABLE_ABORT), 10,
--- a/drivers/i2c/busses/i2c-designware-core.h
+++ b/drivers/i2c/busses/i2c-designware-core.h
@@ -109,6 +109,7 @@
DW_IC_INTR_RX_UNDER | \
DW_IC_INTR_RD_REQ)
+#define DW_IC_ENABLE_ENABLE BIT(0)
#define DW_IC_ENABLE_ABORT BIT(1)
#define DW_IC_STATUS_ACTIVITY BIT(0)
--- a/drivers/i2c/busses/i2c-designware-master.c
+++ b/drivers/i2c/busses/i2c-designware-master.c
@@ -253,6 +253,34 @@ static void i2c_dw_xfer_init(struct dw_i
__i2c_dw_write_intr_mask(dev, DW_IC_INTR_MASTER_MASK);
}
+/*
+ * This function waits for the controller to be idle before disabling I2C
+ * When the controller is not in the IDLE state, the MST_ACTIVITY bit
+ * (IC_STATUS[5]) is set.
+ *
+ * Values:
+ * 0x1 (ACTIVE): Controller not idle
+ * 0x0 (IDLE): Controller is idle
+ *
+ * The function is called after completing the current transfer.
+ *
+ * Returns:
+ * False when the controller is in the IDLE state.
+ * True when the controller is in the ACTIVE state.
+ */
+static bool i2c_dw_is_controller_active(struct dw_i2c_dev *dev)
+{
+ u32 status;
+
+ regmap_read(dev->map, DW_IC_STATUS, &status);
+ if (!(status & DW_IC_STATUS_MASTER_ACTIVITY))
+ return false;
+
+ return regmap_read_poll_timeout(dev->map, DW_IC_STATUS, status,
+ !(status & DW_IC_STATUS_MASTER_ACTIVITY),
+ 1100, 20000) != 0;
+}
+
static int i2c_dw_check_stopbit(struct dw_i2c_dev *dev)
{
u32 val;
@@ -789,6 +817,16 @@ i2c_dw_xfer(struct i2c_adapter *adap, st
}
/*
+ * This happens rarely (~1:500) and is hard to reproduce. Debug trace
+ * showed that IC_STATUS had value of 0x23 when STOP_DET occurred,
+ * if disable IC_ENABLE.ENABLE immediately that can result in
+ * IC_RAW_INTR_STAT.MASTER_ON_HOLD holding SCL low. Check if
+ * controller is still ACTIVE before disabling I2C.
+ */
+ if (i2c_dw_is_controller_active(dev))
+ dev_err(dev->dev, "controller active\n");
+
+ /*
* We must disable the adapter before returning and signaling the end
* of the current transfer. Otherwise the hardware might continue
* generating interrupts which in turn causes a race condition with
