Commit 82dbb57ac8d06dfe8227ba9ab11a49de2b475ae5 upstream.
Some firmware versions of the 9600 series SAS HBA byte-swap the REPORT
ZONES command reply buffer from ATA-ZAC devices by directly accessing the
buffer in the host memory. This does not respect the default command DMA
direction and causes IOMMU page faults on architectures with an IOMMU
enforcing write-only mappings for DMA_FROM_DEVICE DMA driection (e.g. AMD
hosts).
scsi 18:0:0:0: Direct-Access-ZBC ATA WDC WSH722020AL W870 PQ: 0 ANSI: 6
scsi 18:0:0:0: SATA: handle(0x0027), sas_addr(0x300062b2083e7c40), phy(0), device_name(0x5000cca29dc35e11)
scsi 18:0:0:0: enclosure logical id (0x300062b208097c40), slot(0)
scsi 18:0:0:0: enclosure level(0x0000), connector name( C0.0)
scsi 18:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
scsi 18:0:0:0: qdepth(32), tagged(1), scsi_level(7), cmd_que(1)
sd 18:0:0:0: Attached scsi generic sg2 type 20
sd 18:0:0:0: [sdc] Host-managed zoned block device
mpt3sas 0000:41:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0xfff9b200 flags=0x0050]
mpt3sas 0000:41:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0xfff9b300 flags=0x0050]
mpt3sas_cm0: mpt3sas_ctl_pre_reset_handler: Releasing the trace buffer due to adapter reset.
mpt3sas_cm0 fault info from func: mpt3sas_base_make_ioc_ready
mpt3sas_cm0: fault_state(0x2666)!
mpt3sas_cm0: sending diag reset !!
mpt3sas_cm0: diag reset: SUCCESS
sd 18:0:0:0: [sdc] REPORT ZONES start lba 0 failed
sd 18:0:0:0: [sdc] REPORT ZONES: Result: hostbyte=DID_RESET driverbyte=DRIVER_OK
sd 18:0:0:0: [sdc] 0 4096-byte logical blocks: (0 B/0 B)
Avoid such issue by always mapping the buffer of REPORT ZONES commands
using DMA_BIDIRECTIONAL (read+write IOMMU mapping). This is done by
introducing the helper function _base_scsi_dma_map() and using this helper
in _base_build_sg_scmd() and _base_build_sg_scmd_ieee() instead of calling
directly scsi_dma_map().
Fixes: 471ef9d4e498 ("mpt3sas: Build MPI SGL LIST on GEN2 HBAs and IEEE SGL LIST on GEN3 HBAs")
Cc: stable@xxxxxxxxxxxxxxx
Signed-off-by: Damien Le Moal <dlemoal@xxxxxxxxxx>
Link: https://lore.kernel.org/r/20240719073913.179559-3-dlemoal@xxxxxxxxxx
Reviewed-by: Christoph Hellwig <hch@xxxxxx>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@xxxxxxx>
Signed-off-by: Martin K. Petersen <martin.petersen@xxxxxxxxxx>
(cherry picked from commit 82dbb57ac8d06dfe8227ba9ab11a49de2b475ae5)
---
drivers/scsi/mpt3sas/mpt3sas_base.c | 20 ++++++++++++++++++--
1 file changed, 18 insertions(+), 2 deletions(-)
diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.c b/drivers/scsi/mpt3sas/mpt3sas_base.c
index b4495023edb7..cbe10d9a8ae1 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.c
@@ -2221,6 +2221,22 @@ _base_build_zero_len_sge_ieee(struct MPT3SAS_ADAPTER *ioc, void *paddr)
_base_add_sg_single_ieee(paddr, sgl_flags, 0, 0, -1);
}
+static inline int _base_scsi_dma_map(struct scsi_cmnd *cmd)
+{
+ /*
+ * Some firmware versions byte-swap the REPORT ZONES command reply from
+ * ATA-ZAC devices by directly accessing in the host buffer. This does
+ * not respect the default command DMA direction and causes IOMMU page
+ * faults on some architectures with an IOMMU enforcing write mappings
+ * (e.g. AMD hosts). Avoid such issue by making the report zones buffer
+ * mapping bi-directional.
+ */
+ if (cmd->cmnd[0] == ZBC_IN && cmd->cmnd[1] == ZI_REPORT_ZONES)
+ cmd->sc_data_direction = DMA_BIDIRECTIONAL;
+
+ return scsi_dma_map(cmd);
+}
+
/**
* _base_build_sg_scmd - main sg creation routine
* pcie_device is unused here!
@@ -2267,7 +2283,7 @@ _base_build_sg_scmd(struct MPT3SAS_ADAPTER *ioc,
sgl_flags = sgl_flags << MPI2_SGE_FLAGS_SHIFT;
sg_scmd = scsi_sglist(scmd);
- sges_left = scsi_dma_map(scmd);
+ sges_left = _base_scsi_dma_map(scmd);
if (sges_left < 0) {
sdev_printk(KERN_ERR, scmd->device,
"pci_map_sg failed: request for %d bytes!\n",
@@ -2415,7 +2431,7 @@ _base_build_sg_scmd_ieee(struct MPT3SAS_ADAPTER *ioc,
}
sg_scmd = scsi_sglist(scmd);
- sges_left = scsi_dma_map(scmd);
+ sges_left = _base_scsi_dma_map(scmd);
if (sges_left < 0) {
sdev_printk(KERN_ERR, scmd->device,
"pci_map_sg failed: request for %d bytes!\n",
--
2.45.2
