[PATCH] mtd: rawnand: Ensure ECC configuration is propagated to upper layers

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Until recently the "upper layer" was MTD. But following incremental
reworks to bring spi-nand support and more recently generic ECC support,
there is now an intermediate "generic NAND" layer that also needs to get
access to some values. When using "converted" ECC engines, like the
software ones, these values are already propagated correctly. But
otherwise when using good old raw NAND controller drivers, we need to
manually set these values ourselves at the end of the "scan" operation,
once these values have been negotiated.

Without this propagation, later (generic) checks like the one warning
users that the ECC strength is not high enough might simply no longer
work.

Fixes: 8c126720fe10 ("mtd: rawnand: Use the ECC framework nand_ecc_is_strong_enough() helper")
Cc: stable@xxxxxxxxxxxxxxx
Reported-by: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
Closes: https://lore.kernel.org/all/Zhe2JtvvN1M4Ompw@xxxxxxxxxxxxxx/
Signed-off-by: Miquel Raynal <miquel.raynal@xxxxxxxxxxx>
Tested-by: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
Link: https://lore.kernel.org/linux-mtd/20240507085842.108844-1-miquel.raynal@xxxxxxxxxxx

diff --git a/drivers/mtd/nand/raw/nand_base.c b/drivers/mtd/nand/raw/nand_base.c
index d7dbbd469b89..acd137dd0957 100644
--- a/drivers/mtd/nand/raw/nand_base.c
+++ b/drivers/mtd/nand/raw/nand_base.c
@@ -6301,6 +6301,7 @@ static const struct nand_ops rawnand_ops = {
 static int nand_scan_tail(struct nand_chip *chip)
 {
 	struct mtd_info *mtd = nand_to_mtd(chip);
+	struct nand_device *base = &chip->base;
 	struct nand_ecc_ctrl *ecc = &chip->ecc;
 	int ret, i;
 
@@ -6445,9 +6446,13 @@ static int nand_scan_tail(struct nand_chip *chip)
 	if (!ecc->write_oob_raw)
 		ecc->write_oob_raw = ecc->write_oob;
 
-	/* propagate ecc info to mtd_info */
+	/* Propagate ECC info to the generic NAND and MTD layers */
 	mtd->ecc_strength = ecc->strength;
+	if (!base->ecc.ctx.conf.strength)
+		base->ecc.ctx.conf.strength = ecc->strength;
 	mtd->ecc_step_size = ecc->size;
+	if (!base->ecc.ctx.conf.step_size)
+		base->ecc.ctx.conf.step_size = ecc->size;
 
 	/*
 	 * Set the number of read / write steps for one page depending on ECC
@@ -6455,6 +6460,8 @@ static int nand_scan_tail(struct nand_chip *chip)
 	 */
 	if (!ecc->steps)
 		ecc->steps = mtd->writesize / ecc->size;
+	if (!base->ecc.ctx.nsteps)
+		base->ecc.ctx.nsteps = ecc->steps;
 	if (ecc->steps * ecc->size != mtd->writesize) {
 		WARN(1, "Invalid ECC parameters\n");
 		ret = -EINVAL;





[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux