Re: Patch "MIPS: pci: lantiq: restore reset gpio polarity" has been added to the 6.9-stable tree

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2024-06-24 19:01, gregkh@xxxxxxxxxxxxxxxxxxx wrote:
This is a note to let you know that I've just added the patch titled

    MIPS: pci: lantiq: restore reset gpio polarity

to the 6.9-stable tree which can be found at:

http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     mips-pci-lantiq-restore-reset-gpio-polarity.patch
and it can be found in the queue-6.9 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@xxxxxxxxxxxxxxx> know about it.


This patch is buggy and should not go into the stable trees.
It has already been reverted upstream in the mips-fixes.

Thank you very much and sorry for the inconvenience,
Martin



From 277a0363120276645ae598d8d5fea7265e076ae9 Mon Sep 17 00:00:00 2001
From: Martin Schiller <ms@xxxxxxxxxx>
Date: Fri, 7 Jun 2024 11:04:00 +0200
Subject: MIPS: pci: lantiq: restore reset gpio polarity

From: Martin Schiller <ms@xxxxxxxxxx>

commit 277a0363120276645ae598d8d5fea7265e076ae9 upstream.

Commit 90c2d2eb7ab5 ("MIPS: pci: lantiq: switch to using gpiod API") not only switched to the gpiod API, but also inverted / changed the polarity
of the GPIO.

According to the PCI specification, the RST# pin is an active-low
signal. However, most of the device trees that have been widely used for
a long time (mainly in the openWrt project) define this GPIO as
active-high and the old driver code inverted the signal internally.

Apparently there are actually boards where the reset gpio must be
operated inverted. For this reason, we cannot use the GPIOD_OUT_LOW/HIGH
flag for initialization. Instead, we must explicitly set the gpio to
value 1 in order to take into account any "GPIO_ACTIVE_LOW" flag that
may have been set.

In order to remain compatible with all these existing device trees, we
should therefore keep the logic as it was before the commit.

Fixes: 90c2d2eb7ab5 ("MIPS: pci: lantiq: switch to using gpiod API")
Cc: stable@xxxxxxxxxxxxxxx
Signed-off-by: Martin Schiller <ms@xxxxxxxxxx>
Signed-off-by: Thomas Bogendoerfer <tsbogend@xxxxxxxxxxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
 arch/mips/pci/pci-lantiq.c |    8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

--- a/arch/mips/pci/pci-lantiq.c
+++ b/arch/mips/pci/pci-lantiq.c
@@ -124,14 +124,14 @@ static int ltq_pci_startup(struct platfo
 		clk_disable(clk_external);

 	/* setup reset gpio used by pci */
-	reset_gpio = devm_gpiod_get_optional(&pdev->dev, "reset",
-					     GPIOD_OUT_LOW);
+ reset_gpio = devm_gpiod_get_optional(&pdev->dev, "reset", GPIOD_ASIS);
 	error = PTR_ERR_OR_ZERO(reset_gpio);
 	if (error) {
 		dev_err(&pdev->dev, "failed to request gpio: %d\n", error);
 		return error;
 	}
 	gpiod_set_consumer_name(reset_gpio, "pci_reset");
+	gpiod_direction_output(reset_gpio, 1);

 	/* enable auto-switching between PCI and EBU */
 	ltq_pci_w32(0xa, PCI_CR_CLK_CTRL);
@@ -194,10 +194,10 @@ static int ltq_pci_startup(struct platfo

 	/* toggle reset pin */
 	if (reset_gpio) {
-		gpiod_set_value_cansleep(reset_gpio, 1);
+		gpiod_set_value_cansleep(reset_gpio, 0);
 		wmb();
 		mdelay(1);
-		gpiod_set_value_cansleep(reset_gpio, 0);
+		gpiod_set_value_cansleep(reset_gpio, 1);
 	}
 	return 0;
 }


Patches currently in stable-queue which might be from ms@xxxxxxxxxx are

queue-6.9/mips-pci-lantiq-restore-reset-gpio-polarity.patch




[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux