From: Derek Fang <derek.fang@xxxxxxxxxxx> [ Upstream commit 103abab975087e1f01b76fcb54c91dbb65dbc249 ] The codec leaves tie combo jack's sleeve/ring2 to floating status default. It would cause electric noise while connecting the active speaker jack during boot or shutdown. This patch requests a gpio to control the additional jack circuit to tie the contacts to the ground or floating. Signed-off-by: Derek Fang <derek.fang@xxxxxxxxxxx> Link: https://msgid.link/r/20240408091057.14165-1-derek.fang@xxxxxxxxxxx Signed-off-by: Mark Brown <broonie@xxxxxxxxxx> Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx> --- sound/soc/codecs/rt5645.c | 25 +++++++++++++++++++++++++ 1 file changed, 25 insertions(+) diff --git a/sound/soc/codecs/rt5645.c b/sound/soc/codecs/rt5645.c index e0da151508309..b69f6afa0ae40 100644 --- a/sound/soc/codecs/rt5645.c +++ b/sound/soc/codecs/rt5645.c @@ -441,6 +441,7 @@ struct rt5645_priv { struct regmap *regmap; struct i2c_client *i2c; struct gpio_desc *gpiod_hp_det; + struct gpio_desc *gpiod_cbj_sleeve; struct snd_soc_jack *hp_jack; struct snd_soc_jack *mic_jack; struct snd_soc_jack *btn_jack; @@ -3183,6 +3184,9 @@ static int rt5645_jack_detect(struct snd_soc_component *component, int jack_inse regmap_update_bits(rt5645->regmap, RT5645_IN1_CTRL2, RT5645_CBJ_MN_JD, 0); + if (rt5645->gpiod_cbj_sleeve) + gpiod_set_value(rt5645->gpiod_cbj_sleeve, 1); + msleep(600); regmap_read(rt5645->regmap, RT5645_IN1_CTRL3, &val); val &= 0x7; @@ -3199,6 +3203,8 @@ static int rt5645_jack_detect(struct snd_soc_component *component, int jack_inse snd_soc_dapm_disable_pin(dapm, "Mic Det Power"); snd_soc_dapm_sync(dapm); rt5645->jack_type = SND_JACK_HEADPHONE; + if (rt5645->gpiod_cbj_sleeve) + gpiod_set_value(rt5645->gpiod_cbj_sleeve, 0); } if (rt5645->pdata.level_trigger_irq) regmap_update_bits(rt5645->regmap, RT5645_IRQ_CTRL2, @@ -3226,6 +3232,9 @@ static int rt5645_jack_detect(struct snd_soc_component *component, int jack_inse if (rt5645->pdata.level_trigger_irq) regmap_update_bits(rt5645->regmap, RT5645_IRQ_CTRL2, RT5645_JD_1_1_MASK, RT5645_JD_1_1_INV); + + if (rt5645->gpiod_cbj_sleeve) + gpiod_set_value(rt5645->gpiod_cbj_sleeve, 0); } return rt5645->jack_type; @@ -3958,6 +3967,16 @@ static int rt5645_i2c_probe(struct i2c_client *i2c) return ret; } + rt5645->gpiod_cbj_sleeve = devm_gpiod_get_optional(&i2c->dev, "cbj-sleeve", + GPIOD_OUT_LOW); + + if (IS_ERR(rt5645->gpiod_cbj_sleeve)) { + ret = PTR_ERR(rt5645->gpiod_cbj_sleeve); + dev_info(&i2c->dev, "failed to initialize gpiod, ret=%d\n", ret); + if (ret != -ENOENT) + return ret; + } + for (i = 0; i < ARRAY_SIZE(rt5645->supplies); i++) rt5645->supplies[i].supply = rt5645_supply_names[i]; @@ -4205,6 +4224,9 @@ static void rt5645_i2c_remove(struct i2c_client *i2c) cancel_delayed_work_sync(&rt5645->jack_detect_work); cancel_delayed_work_sync(&rt5645->rcclock_work); + if (rt5645->gpiod_cbj_sleeve) + gpiod_set_value(rt5645->gpiod_cbj_sleeve, 0); + regulator_bulk_disable(ARRAY_SIZE(rt5645->supplies), rt5645->supplies); } @@ -4220,6 +4242,9 @@ static void rt5645_i2c_shutdown(struct i2c_client *i2c) 0); msleep(20); regmap_write(rt5645->regmap, RT5645_RESET, 0); + + if (rt5645->gpiod_cbj_sleeve) + gpiod_set_value(rt5645->gpiod_cbj_sleeve, 0); } static int __maybe_unused rt5645_sys_suspend(struct device *dev) -- 2.43.0
