Re: [PATCH] serial: 8250_dw: Revert: Do not reclock if already at correct rate

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Mar 29, 2024 at 12:42:14PM +0100, Hans de Goede wrote:
> Hi Peter,
> 
> On 3/29/24 3:35 AM, Peter Collingbourne wrote:
> > On Thu, Mar 28, 2024 at 5:35 AM Hans de Goede <hdegoede@xxxxxxxxxx> wrote:
> >>
> >> Hi,
> >>
> >> On 3/28/24 8:10 AM, Hans de Goede wrote:
> >>> Hi,
> >>>
> >>> On 3/18/24 7:52 PM, Peter Collingbourne wrote:
> >>>> On Mon, Mar 18, 2024 at 3:36 AM Andy Shevchenko
> >>>> <andriy.shevchenko@xxxxxxxxxxxxxxx> wrote:
> >>>>>
> >>>>> On Sun, Mar 17, 2024 at 10:41:23PM +0100, Hans de Goede wrote:
> >>>>>> Commit e5d6bd25f93d ("serial: 8250_dw: Do not reclock if already at
> >>>>>> correct rate") breaks the dw UARTs on Intel Bay Trail (BYT) and
> >>>>>> Cherry Trail (CHT) SoCs.
> >>>>>>
> >>>>>> Before this change the RTL8732BS Bluetooth HCI which is found
> >>>>>> connected over the dw UART on both BYT and CHT boards works properly:
> >>>>>>
> >>>>>> Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723
> >>>>>> Bluetooth: hci0: RTL: rom_version status=0 version=1
> >>>>>> Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_fw.bin
> >>>>>> Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_config-OBDA8723.bin
> >>>>>> Bluetooth: hci0: RTL: cfg_sz 64, total sz 24508
> >>>>>> Bluetooth: hci0: RTL: fw version 0x365d462e
> >>>>>>
> >>>>>> where as after this change probing it fails:
> >>>>>>
> >>>>>> Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723
> >>>>>> Bluetooth: hci0: RTL: rom_version status=0 version=1
> >>>>>> Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_fw.bin
> >>>>>> Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_config-OBDA8723.bin
> >>>>>> Bluetooth: hci0: RTL: cfg_sz 64, total sz 24508
> >>>>>> Bluetooth: hci0: command 0xfc20 tx timeout
> >>>>>> Bluetooth: hci0: RTL: download fw command failed (-110)
> >>>>>>
> >>>>>> Revert the changes to fix this regression.
> >>>>>
> >>>>> Reviewed-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
> >>>>>
> >>>>>> Note it is not entirely clear to me why this commit is causing
> >>>>>> this issue. Maybe probe() needs to explicitly set the clk rate
> >>>>>> which it just got (that feels like a clk driver issue) or maybe
> >>>>>> the issue is that unless setup before hand by firmware /
> >>>>>> the bootloader serial8250_update_uartclk() needs to be called
> >>>>>> at least once to setup things ?  Note that probe() does not call
> >>>>>> serial8250_update_uartclk(), this is only called from the
> >>>>>> dw8250_clk_notifier_cb()
> >>>>>>
> >>>>>> This requires more debugging which is why I'm proposing
> >>>>>> a straight revert to fix the regression ASAP and then this
> >>>>>> can be investigated further.
> >>>>>
> >>>>> Yep. When I reviewed the original submission I was got puzzled with
> >>>>> the CLK APIs. Now I might remember that ->set_rate() can't be called
> >>>>> on prepared/enabled clocks and it's possible the same limitation
> >>>>> is applied to ->round_rate().
> >>>>>
> >>>>> I also tried to find documentation about the requirements for those
> >>>>> APIs, but failed (maybe was not pursuing enough, dunno). If you happen
> >>>>> to know the one, can you point on it?
> >>>>
> >>>> To me it seems to be unlikely to be related to round_rate(). It seems
> >>>> more likely that my patch causes us to never actually set the clock
> >>>> rate (e.g. because uartclk was initialized to the intended clock rate
> >>>> instead of the current actual clock rate).
> >>>
> >>> I agree that the likely cause is that we never set the clk-rate. I'm not
> >>> sure if the issue is us never actually calling clk_set_rate() or if
> >>> the issue is that by never calling clk_set_rate() dw8250_clk_notifier_cb()
> >>> never gets called and thus we never call serial8250_update_uartclk()
> >>>
> >>>> It should be possible to
> >>>> confirm by checking the behavior with my patch with `&& p->uartclk !=
> >>>> rate` removed, which I would expect to unbreak Hans's scenario. If my
> >>>> hypothesis is correct, the fix might involve querying the clock with
> >>>> clk_get_rate() in the if instead of reading from uartclk.
> >>>
> >>> Querying the clk with clk_get_rate() instead of reading it from
> >>> uartclk will not help as uartclk gets initialized with clk_get_rate()
> >>> in dw8250_probe(). So I believe that in my scenario clk_get_rate()
> >>> already returns the desired rate causing us to never call clk_set_rate()
> >>> at all which leaves 2 possible root causes for the regressions:
> >>>
> >>> 1. The clk generator has non readable registers and the returned
> >>> rate from clk_get_rate() is a default rate and the actual hw is
> >>> programmed differently, iow we need to call clk_set_rate() at
> >>> least once on this hw to ensure that the clk generator is prggrammed
> >>> properly.
> >>>
> >>> 2. The 8250 code is not working as it should because
> >>> serial8250_update_uartclk() has never been called.
> >>
> >> Ok, so it looks like this actually is an issue with how clk_round_rate()
> >> works on this hw (atm, maybe the clk driver needs fixing).
> >>
> >> I have added the following to debug this:
> >>
> >> diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
> >> index a3acbf0f5da1..3152872e50b2 100644
> >> --- a/drivers/tty/serial/8250/8250_dw.c
> >> +++ b/drivers/tty/serial/8250/8250_dw.c
> >> @@ -306,6 +306,8 @@ static void dw8250_clk_work_cb(struct work_struct *work)
> >>         if (rate <= 0)
> >>                 return;
> >>
> >> +       pr_info("uartclk work_cb clk_get_rate() returns: %ld\n", rate);
> >> +
> >>         up = serial8250_get_port(d->data.line);
> >>
> >>         serial8250_update_uartclk(&up->port, rate);
> >> @@ -353,11 +355,15 @@ static void dw8250_set_termios(struct uart_port *p, struct ktermios *termios,
> >>  {
> >>         unsigned long newrate = tty_termios_baud_rate(termios) * 16;
> >>         struct dw8250_data *d = to_dw8250_data(p->private_data);
> >> +       unsigned long currentrate = clk_get_rate(d->clk);
> >>         long rate;
> >>         int ret;
> >>
> >> +
> >>         rate = clk_round_rate(d->clk, newrate);
> >> -       if (rate > 0 && p->uartclk != rate) {
> >> +       pr_info("uartclk set_termios new: %ld new-rounded: %ld current %ld cached %d\n",
> >> +               newrate, rate, currentrate, p->uartclk);
> >> +       if (rate > 0) {
> >>                 clk_disable_unprepare(d->clk);
> >>                 /*
> >>                  * Note that any clock-notifer worker will block in
> >> @@ -593,6 +599,8 @@ static int dw8250_probe(struct platform_device *pdev)
> >>         if (!p->uartclk)
> >>                 return dev_err_probe(dev, -EINVAL, "clock rate not defined\n");
> >>
> >> +       pr_info("uartclk initial cached %d\n", p->uartclk);
> >> +
> >>         data->pclk = devm_clk_get_optional_enabled(dev, "apb_pclk");
> >>         if (IS_ERR(data->pclk))
> >>                 return PTR_ERR(data->pclk);
> >>
> >> And then I get the following output:
> >>
> >> [    3.119182] uartclk initial cached 44236800
> >> [    3.139923] uartclk work_cb clk_get_rate() returns: 44236800
> >> [    3.152469] uartclk initial cached 44236800
> >> [    3.172165] uartclk work_cb clk_get_rate() returns: 44236800
> >> [   34.128257] uartclk set_termios new: 153600 new-rounded: 44236800 current 44236800 cached 44236800
> >> [   34.130039] uartclk work_cb clk_get_rate() returns: 153600
> >> [   34.131975] uartclk set_termios new: 153600 new-rounded: 153600 current 153600 cached 153600
> >> [   34.132091] uartclk set_termios new: 153600 new-rounded: 153600 current 153600 cached 153600
> >> [   34.132140] uartclk set_termios new: 153600 new-rounded: 153600 current 153600 cached 153600
> >> [   34.132187] uartclk set_termios new: 1843200 new-rounded: 153600 current 153600 cached 153600
> >> [   34.133536] uartclk work_cb clk_get_rate() returns: 1843200
> >>
> >> Notice how the new-rounded just returns the current rate of the clk,
> >> rather then a rounded value of new.
> >>
> >> I'm not familiar enough with the clk framework to debug this further.
> >>
> >> Peter, IMHO we really must revert your commit since it is completely
> >> breaking UARTs on many different Intel boards. Can you please give your
> >> ack for reverting this for now ?
> > 
> > That's fine with me.
> 
> Great, thank you.
> 
> > I will try to dig into the code soon to figure
> > out what is going on unless someone gets there first.
> 
> Thinking some more about this I think the following might
> be going on (this is only a theory I have, not sure at all):
> 
> The 80860F0A:01-update clk itself does not allow
> changing it rate, which is why clk_round_rate() is simply
> returning the current rate of it.
> 
> But its parent, 80860F0A:01-div does allow changing its
> rate and it has only 1 child / consumer,
> the 80860F0A:01-update clk. So because of this
> clk_set_rate() propagates the clk_set_rate() call
> the 8250_dw code does on 80860F0A:01-update to
> 80860F0A:01-div, which is ok to do since there
> are no competing conumers who would be affected
> by the clk-rate change.
> 
> And then the propagated clk_set_rate() call on
> 80860F0A:01-div successfully updates the clk-rate
> and a get_rate on 80860F0A:01-update (which AFAICT
> is just a gate after the divider) now returns
> the new rate.
> 
> Again just a theory but this would explain the weird
> clk_get_rate() behavior.
> 
> In case it helps here is the clk chain for the
> 8250_dw clk:
> 
> lpss_clk (fixed 100MHz) ->
> 80860F0A:01 (gate only?) ->
> 80860F0A:01-div (working set_rate()) ->
> 80860F0A:01-update (gate only ?) ->
> 8500_dw-baudclk
> 
> > Acked-by: Peter Collingbourne <pcc@xxxxxxxxxx>
> 
> Thanks. Greg can we get this merged please
> (it is a regression fix for a 6.8 regression) ?

Will queue it up soon, thanks.

greg k-h




[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux