On 3/27/24 02:58, Louis Chauvet wrote:
The current xdma_synchronize method does not properly wait for the last
transfer to be done. Due to limitations of the XMDA engine, it is not
possible to stop a transfer in the middle of a descriptor. Said
otherwise, if a stop is requested at the end of descriptor "N" and the OS
is fast enough, the DMA controller will effectively stop immediately.
However, if the OS is slightly too slow to request the stop and the DMA
engine starts descriptor "N+1", the N+1 transfer will be performed until
its end. This means that after a terminate_all, the last descriptor must
remain valid and the synchronization must wait for this last descriptor to
be terminated.
Fixes: 855c2e1d1842 ("dmaengine: xilinx: xdma: Rework xdma_terminate_all()")
Fixes: f5c392d106e7 ("dmaengine: xilinx: xdma: Add terminate_all/synchronize callbacks")
Cc: stable@xxxxxxxxxxxxxxx
Suggested-by: Miquel Raynal <miquel.raynal@xxxxxxxxxxx>
Signed-off-by: Louis Chauvet <louis.chauvet@xxxxxxxxxxx>
---
drivers/dma/xilinx/xdma-regs.h | 3 +++
drivers/dma/xilinx/xdma.c | 26 ++++++++++++++++++--------
2 files changed, 21 insertions(+), 8 deletions(-)
diff --git a/drivers/dma/xilinx/xdma-regs.h b/drivers/dma/xilinx/xdma-regs.h
index 98f5f6fb9ff9..6ad08878e938 100644
--- a/drivers/dma/xilinx/xdma-regs.h
+++ b/drivers/dma/xilinx/xdma-regs.h
@@ -117,6 +117,9 @@ struct xdma_hw_desc {
CHAN_CTRL_IE_WRITE_ERROR | \
CHAN_CTRL_IE_DESC_ERROR)
+/* bits of the channel status register */
+#define XDMA_CHAN_STATUS_BUSY BIT(0)
+
#define XDMA_CHAN_STATUS_MASK CHAN_CTRL_START
#define XDMA_CHAN_ERROR_MASK (CHAN_CTRL_IE_DESC_ALIGN_MISMATCH | \
diff --git a/drivers/dma/xilinx/xdma.c b/drivers/dma/xilinx/xdma.c
index b9788aa8f6b7..5a3a3293b21b 100644
--- a/drivers/dma/xilinx/xdma.c
+++ b/drivers/dma/xilinx/xdma.c
@@ -71,6 +71,8 @@ struct xdma_chan {
enum dma_transfer_direction dir;
struct dma_slave_config cfg;
u32 irq;
+ struct completion last_interrupt;
+ bool stop_requested;
};
/**
@@ -376,6 +378,8 @@ static int xdma_xfer_start(struct xdma_chan *xchan)
return ret;
xchan->busy = true;
+ xchan->stop_requested = false;
+ reinit_completion(&xchan->last_interrupt);
If stop_requested is true, it should not start another transfer. So I
would suggest to add
if (xchan->stop_requested)
return -ENODEV;
at the beginning of xdma_xfer_start().
xdma_xfer_start() is protected by chan lock.
return 0;
}
@@ -387,7 +391,6 @@ static int xdma_xfer_start(struct xdma_chan *xchan)
static int xdma_xfer_stop(struct xdma_chan *xchan)
{
int ret;
- u32 val;
struct xdma_device *xdev = xchan->xdev_hdl;
/* clear run stop bit to prevent any further auto-triggering */
@@ -395,13 +398,7 @@ static int xdma_xfer_stop(struct xdma_chan *xchan)
CHAN_CTRL_RUN_STOP);
if (ret)
return ret;
Above two lines can be removed with your change.
-
- /* Clear the channel status register */
- ret = regmap_read(xdev->rmap, xchan->base + XDMA_CHAN_STATUS_RC, &val);
- if (ret)
- return ret;
-
- return 0;
+ return ret;
}
/**
@@ -474,6 +471,8 @@ static int xdma_alloc_channels(struct xdma_device *xdev,
xchan->xdev_hdl = xdev;
xchan->base = base + i * XDMA_CHAN_STRIDE;
xchan->dir = dir;
+ xchan->stop_requested = false;
+ init_completion(&xchan->last_interrupt);
ret = xdma_channel_init(xchan);
if (ret)
@@ -521,6 +520,7 @@ static int xdma_terminate_all(struct dma_chan *chan)
spin_lock_irqsave(&xdma_chan->vchan.lock, flags);
xdma_chan->busy = false;
+ xdma_chan->stop_requested = true;
vd = vchan_next_desc(&xdma_chan->vchan);
if (vd) {
list_del(&vd->node);
@@ -542,6 +542,13 @@ static int xdma_terminate_all(struct dma_chan *chan)
static void xdma_synchronize(struct dma_chan *chan)
{
struct xdma_chan *xdma_chan = to_xdma_chan(chan);
+ struct xdma_device *xdev = xdma_chan->xdev_hdl;
+ int st = 0;
+
+ /* If the engine continues running, wait for the last interrupt */
+ regmap_read(xdev->rmap, xdma_chan->base + XDMA_CHAN_STATUS, &st);
+ if (st & XDMA_CHAN_STATUS_BUSY)
+ wait_for_completion_timeout(&xdma_chan->last_interrupt, msecs_to_jiffies(1000));
I suggest to add error message for timeout case.
vchan_synchronize(&xdma_chan->vchan);
}
@@ -876,6 +883,9 @@ static irqreturn_t xdma_channel_isr(int irq, void *dev_id)
u32 st;
bool repeat_tx;
+ if (xchan->stop_requested)
+ complete(&xchan->last_interrupt);
+
This should be moved to the end of function to make sure processing
previous transfer is completed.
out:
if (xchan->stop_requested) {
xchan->busy = false;
complete(&xchan->last_interrupt);
}
spin_unlock(&xchan->vchan.lock);
return IRQ_HANDLED;
Thanks,
Lizhi
spin_lock(&xchan->vchan.lock);
/* get submitted request */
