From: Xin Ji <xji@xxxxxxxxxxxxxxxx> [ Upstream commit e3af7053de3f685c96158373bc234b2feca1f160 ] Polling firmware HPD GPIO status, set HPD irq detect window to 2ms after firmware HPD GPIO initial done Signed-off-by: Xin Ji <xji@xxxxxxxxxxxxxxxx> Reviewed-by: Robert Foss <rfoss@xxxxxxxxxx> Signed-off-by: Robert Foss <rfoss@xxxxxxxxxx> Link: https://patchwork.freedesktop.org/patch/msgid/20231120091038.284825-2-xji@xxxxxxxxxxxxxxxx Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx> --- drivers/gpu/drm/bridge/analogix/anx7625.c | 51 ++++++++++++++++------- drivers/gpu/drm/bridge/analogix/anx7625.h | 4 ++ 2 files changed, 40 insertions(+), 15 deletions(-) diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c index 51abe42c639e..ef31033439bc 100644 --- a/drivers/gpu/drm/bridge/analogix/anx7625.c +++ b/drivers/gpu/drm/bridge/analogix/anx7625.c @@ -1298,10 +1298,32 @@ static void anx7625_config(struct anx7625_data *ctx) XTAL_FRQ_SEL, XTAL_FRQ_27M); } +static int anx7625_hpd_timer_config(struct anx7625_data *ctx) +{ + int ret; + + /* Set irq detect window to 2ms */ + ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, + HPD_DET_TIMER_BIT0_7, HPD_TIME & 0xFF); + ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, + HPD_DET_TIMER_BIT8_15, + (HPD_TIME >> 8) & 0xFF); + ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, + HPD_DET_TIMER_BIT16_23, + (HPD_TIME >> 16) & 0xFF); + + return ret; +} + +static int anx7625_read_hpd_gpio_config_status(struct anx7625_data *ctx) +{ + return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, GPIO_CTRL_2); +} + static void anx7625_disable_pd_protocol(struct anx7625_data *ctx) { struct device *dev = ctx->dev; - int ret; + int ret, val; /* Reset main ocm */ ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 0x88, 0x40); @@ -1315,6 +1337,19 @@ static void anx7625_disable_pd_protocol(struct anx7625_data *ctx) DRM_DEV_DEBUG_DRIVER(dev, "disable PD feature fail.\n"); else DRM_DEV_DEBUG_DRIVER(dev, "disable PD feature succeeded.\n"); + + /* + * Make sure the HPD GPIO already be configured after OCM release before + * setting HPD detect window register. Here we poll the status register + * at maximum 40ms, then config HPD irq detect window register + */ + readx_poll_timeout(anx7625_read_hpd_gpio_config_status, + ctx, val, + ((val & HPD_SOURCE) || (val < 0)), + 2000, 2000 * 20); + + /* Set HPD irq detect window to 2ms */ + anx7625_hpd_timer_config(ctx); } static int anx7625_ocm_loading_check(struct anx7625_data *ctx) @@ -1437,20 +1472,6 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx) static int anx7625_read_hpd_status_p0(struct anx7625_data *ctx) { - int ret; - - /* Set irq detect window to 2ms */ - ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, - HPD_DET_TIMER_BIT0_7, HPD_TIME & 0xFF); - ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, - HPD_DET_TIMER_BIT8_15, - (HPD_TIME >> 8) & 0xFF); - ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, - HPD_DET_TIMER_BIT16_23, - (HPD_TIME >> 16) & 0xFF); - if (ret < 0) - return ret; - return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, SYSTEM_STSTUS); } diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h index 5af819611ebc..66ebee7f3d83 100644 --- a/drivers/gpu/drm/bridge/analogix/anx7625.h +++ b/drivers/gpu/drm/bridge/analogix/anx7625.h @@ -259,6 +259,10 @@ #define AP_MIPI_RX_EN BIT(5) /* 1: MIPI RX input in 0: no RX in */ #define AP_DISABLE_PD BIT(6) #define AP_DISABLE_DISPLAY BIT(7) + +#define GPIO_CTRL_2 0x49 +#define HPD_SOURCE BIT(6) + /***************************************************************/ /* Register definition of device address 0x84 */ #define MIPI_PHY_CONTROL_3 0x03 -- 2.43.0
