[PATCH v6 5/7] serial: core, imx: do not set RS485 enabled if it is not supported

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



If the imx driver cannot support RS485 it nullifies the ports
rs485_supported structure. But it still calls uart_get_rs485_mode() which
may set the RS485_ENABLED flag nevertheless.

This may lead to an attempt to configure RS485 even if it is not supported
when the flag is evaluated in uart_configure_port() at port startup.

Avoid this by bailing out of uart_get_rs485_mode() if the RS485_ENABLED
flag is not supported by the caller.

With this fix a check for RTS availability is now obsolete in the imx
driver, since it can not evaluate to true any more. So remove this check.

Furthermore the explicit nullifcation of rs485_supported is not needed,
since the memory has already been set to zeros at allocation. So remove
this, too.

Fixes: 00d7a00e2a6f ("serial: imx: Fill in rs485_supported")
Cc: Shawn Guo <shawnguo@xxxxxxxxxx>
Cc: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
Cc: stable@xxxxxxxxxxxxxxx
Suggested-by: Uwe Kleine-König <u.kleine-koenig@xxxxxxxxxxxxxx>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@xxxxxxxxxx>
---
 drivers/tty/serial/imx.c         | 7 -------
 drivers/tty/serial/serial_core.c | 3 +++
 2 files changed, 3 insertions(+), 7 deletions(-)

diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 9cffeb23112b..198ce7e7bc8b 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -2206,7 +2206,6 @@ static enum hrtimer_restart imx_trigger_stop_tx(struct hrtimer *t)
 	return HRTIMER_NORESTART;
 }
 
-static const struct serial_rs485 imx_no_rs485 = {};	/* No RS485 if no RTS */
 static const struct serial_rs485 imx_rs485_supported = {
 	.flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND |
 		 SER_RS485_RX_DURING_TX,
@@ -2290,8 +2289,6 @@ static int imx_uart_probe(struct platform_device *pdev)
 	/* RTS is required to control the RS485 transmitter */
 	if (sport->have_rtscts || sport->have_rtsgpio)
 		sport->port.rs485_supported = imx_rs485_supported;
-	else
-		sport->port.rs485_supported = imx_no_rs485;
 	sport->port.flags = UPF_BOOT_AUTOCONF;
 	timer_setup(&sport->timer, imx_uart_timeout, 0);
 
@@ -2328,10 +2325,6 @@ static int imx_uart_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	if (sport->port.rs485.flags & SER_RS485_ENABLED &&
-	    (!sport->have_rtscts && !sport->have_rtsgpio))
-		dev_err(&pdev->dev, "no RTS control, disabling rs485\n");
-
 	/*
 	 * If using the i.MX UART RTS/CTS control then the RTS (CTS_B)
 	 * signal cannot be set low during transmission in case the
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index 28bcbc686c67..93e4e1693601 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -3600,6 +3600,9 @@ int uart_get_rs485_mode(struct uart_port *port)
 	u32 rs485_delay[2];
 	int ret;
 
+	if (!(port->rs485_supported.flags & SER_RS485_ENABLED))
+		return 0;
+
 	ret = device_property_read_u32_array(dev, "rs485-rts-delay",
 					     rs485_delay, 2);
 	if (!ret) {
-- 
2.43.0





[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux