This reverts commit 8bea147dfdf823eaa8d3baeccc7aeb041b41944b.
The phy soft reset GUSB2PHYCFG.PHYSOFTRST only applies to UTMI phy, not
ULPI. This fix is incomplete.
Cc: stable@xxxxxxxxxxxxxxx
Fixes: 8bea147dfdf8 ("usb: dwc3: Soft reset phy on probe for host")
Reported-by: Köry Maincent <kory.maincent@xxxxxxxxxxx>
Closes: https://lore.kernel.org/linux-usb/20231205151959.5236c231@kmaincent-XPS-13-7390
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@xxxxxxxxxxxx>
---
drivers/usb/dwc3/core.c | 39 +--------------------------------------
1 file changed, 1 insertion(+), 38 deletions(-)
diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index b101dbf8c5dc..832c41fec4f7 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -279,46 +279,9 @@ int dwc3_core_soft_reset(struct dwc3 *dwc)
* XHCI driver will reset the host block. If dwc3 was configured for
* host-only mode or current role is host, then we can return early.
*/
- if (dwc->current_dr_role == DWC3_GCTL_PRTCAP_HOST)
+ if (dwc->dr_mode == USB_DR_MODE_HOST || dwc->current_dr_role == DWC3_GCTL_PRTCAP_HOST)
return 0;
- /*
- * If the dr_mode is host and the dwc->current_dr_role is not the
- * corresponding DWC3_GCTL_PRTCAP_HOST, then the dwc3_core_init_mode
- * isn't executed yet. Ensure the phy is ready before the controller
- * updates the GCTL.PRTCAPDIR or other settings by soft-resetting
- * the phy.
- *
- * Note: GUSB3PIPECTL[n] and GUSB2PHYCFG[n] are port settings where n
- * is port index. If this is a multiport host, then we need to reset
- * all active ports.
- */
- if (dwc->dr_mode == USB_DR_MODE_HOST) {
- u32 usb3_port;
- u32 usb2_port;
-
- usb3_port = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0));
- usb3_port |= DWC3_GUSB3PIPECTL_PHYSOFTRST;
- dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), usb3_port);
-
- usb2_port = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
- usb2_port |= DWC3_GUSB2PHYCFG_PHYSOFTRST;
- dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), usb2_port);
-
- /* Small delay for phy reset assertion */
- usleep_range(1000, 2000);
-
- usb3_port &= ~DWC3_GUSB3PIPECTL_PHYSOFTRST;
- dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), usb3_port);
-
- usb2_port &= ~DWC3_GUSB2PHYCFG_PHYSOFTRST;
- dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), usb2_port);
-
- /* Wait for clock synchronization */
- msleep(50);
- return 0;
- }
-
reg = dwc3_readl(dwc->regs, DWC3_DCTL);
reg |= DWC3_DCTL_CSFTRST;
reg &= ~DWC3_DCTL_RUN_STOP;
--
2.28.0
