The following commit has been merged into the x86/urgent branch of tip: Commit-ID: 69a7386c1ec25476a0c78ffeb59de08a2a08f495 Gitweb: https://git.kernel.org/tip/69a7386c1ec25476a0c78ffeb59de08a2a08f495 Author: Thomas Gleixner <tglx@xxxxxxxxxxxxx> AuthorDate: Fri, 15 Dec 2023 09:58:58 +01:00 Committer: Borislav Petkov (AMD) <bp@xxxxxxxxx> CommitterDate: Fri, 15 Dec 2023 19:33:54 +01:00 x86/smpboot/64: Handle X2APIC BIOS inconsistency gracefully Chris reported that a Dell PowerEdge T340 system stopped to boot when upgrading to a kernel which contains the parallel hotplug changes. Disabling parallel hotplug on the kernel command line makes it boot again. It turns out that the Dell BIOS has x2APIC enabled and the boot CPU comes up in X2APIC mode, but the APs come up inconsistently in xAPIC mode. Parallel hotplug requires that the upcoming CPU reads out its APIC ID from the local APIC in order to map it to the Linux CPU number. In this particular case the readout on the APs uses the MMIO mapped registers because the BIOS failed to enable x2APIC mode. That readout results in a page fault because the kernel does not have the APIC MMIO space mapped when X2APIC mode was enabled by the BIOS on the boot CPU and the kernel switched to X2APIC mode early. That page fault can't be handled on the upcoming CPU that early and results in a silent boot failure. If parallel hotplug is disabled the system boots because in that case the APIC ID read is not required as the Linux CPU number is provided to the AP in the smpboot control word. When the kernel uses x2APIC mode then the APs are switched to x2APIC mode too slightly later in the bringup process, but there is no reason to do it that late. Cure the BIOS bogosity by checking in the parallel bootup path whether the kernel uses x2APIC mode and if so switching over the APs to x2APIC mode before the APIC ID readout. Fixes: 0c7ffa32dbd6 ("x86/smpboot/64: Implement arch_cpuhp_init_parallel_bringup() and enable it") Reported-by: Chris Lindee <chris.lindee@xxxxxxxxx> Signed-off-by: Thomas Gleixner <tglx@xxxxxxxxxxxxx> Signed-off-by: Borislav Petkov (AMD) <bp@xxxxxxxxx> Reviewed-by: Ashok Raj <ashok.raj@xxxxxxxxx> Tested-by: Chris Lindee <chris.lindee@xxxxxxxxx> Cc: stable@xxxxxxxxxxxxxxx Link: https://lore.kernel.org/r/CA%2B2tU59853R49EaU_tyvOZuOTDdcU0RshGyydccp9R1NX9bEeQ@xxxxxxxxxxxxxx --- arch/x86/kernel/head_64.S | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/arch/x86/kernel/head_64.S b/arch/x86/kernel/head_64.S index 086a2c3..0f81032 100644 --- a/arch/x86/kernel/head_64.S +++ b/arch/x86/kernel/head_64.S @@ -255,6 +255,22 @@ SYM_INNER_LABEL(secondary_startup_64_no_verify, SYM_L_GLOBAL) testl $X2APIC_ENABLE, %eax jnz .Lread_apicid_msr +#ifdef CONFIG_X86_X2APIC + /* + * If system is in X2APIC mode then MMIO base might not be + * mapped causing the MMIO read below to fault. Faults can't + * be handled at that point. + */ + cmpl $0, x2apic_mode(%rip) + jz .Lread_apicid_mmio + + /* Force the AP into X2APIC mode. */ + orl $X2APIC_ENABLE, %eax + wrmsr + jmp .Lread_apicid_msr +#endif + +.Lread_apicid_mmio: /* Read the APIC ID from the fix-mapped MMIO space. */ movq apic_mmio_base(%rip), %rcx addq $APIC_ID, %rcx
