6.5-stable review patch. If anyone has any objections, please let me know. ------------------ From: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx> commit 4cf478dc5d707e56aefa258c049872eff054a353 upstream. Some variants in this series of UART controllers have GPIO pins that are shared between GPIO and modem control lines. The pin mux mode (GPIO or modem control lines) can be set for each ports (channels) supported by the variant. This adds a property to the device tree to set the GPIO pin mux to modem control lines on selected ports if needed. Cc: stable@xxxxxxxxxxxxxxx # 6.1.x Signed-off-by: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx> Acked-by: Conor Dooley <conor.dooley@xxxxxxxxxxxxx> Reviewed-by: Lech Perczak <lech.perczak@xxxxxxxxxxxxxxx> Acked-by: Rob Herring <robh@xxxxxxxxxx> Link: https://lore.kernel.org/r/20230807214556.540627-4-hugo@xxxxxxxxxxx Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx> --- Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt | 46 +++++++++++++ 1 file changed, 46 insertions(+) --- a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt +++ b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt @@ -23,6 +23,9 @@ Optional properties: 1 = active low. - irda-mode-ports: An array that lists the indices of the port that should operate in IrDA mode. +- nxp,modem-control-line-ports: An array that lists the indices of the port that + should have shared GPIO lines configured as + modem control lines. Example: sc16is750: sc16is750@51 { @@ -35,6 +38,26 @@ Example: #gpio-cells = <2>; }; + sc16is752: sc16is752@53 { + compatible = "nxp,sc16is752"; + reg = <0x53>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + nxp,modem-control-line-ports = <1>; /* Port 1 as modem control lines */ + gpio-controller; /* Port 0 as GPIOs */ + #gpio-cells = <2>; + }; + + sc16is752: sc16is752@54 { + compatible = "nxp,sc16is752"; + reg = <0x54>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + nxp,modem-control-line-ports = <0 1>; /* Ports 0 and 1 as modem control lines */ + }; + * spi as bus Required properties: @@ -59,6 +82,9 @@ Optional properties: 1 = active low. - irda-mode-ports: An array that lists the indices of the port that should operate in IrDA mode. +- nxp,modem-control-line-ports: An array that lists the indices of the port that + should have shared GPIO lines configured as + modem control lines. Example: sc16is750: sc16is750@0 { @@ -70,3 +96,23 @@ Example: gpio-controller; #gpio-cells = <2>; }; + + sc16is752: sc16is752@1 { + compatible = "nxp,sc16is752"; + reg = <1>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + nxp,modem-control-line-ports = <1>; /* Port 1 as modem control lines */ + gpio-controller; /* Port 0 as GPIOs */ + #gpio-cells = <2>; + }; + + sc16is752: sc16is752@2 { + compatible = "nxp,sc16is752"; + reg = <2>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + nxp,modem-control-line-ports = <0 1>; /* Ports 0 and 1 as modem control lines */ + };
