From: Lukas Wunner <lukas@xxxxxxxxx> [ Upstream commit 038ee49fef18710bedd38b531d173ccd746b2d8d ] RS485-enabled UART ports on TI Sitara SoCs with active-low polarity exhibit a Transmit Enable glitch on ->set_termios(): omap8250_restore_regs(), which is called from omap_8250_set_termios(), sets the TCRTLR bit in the MCR register and clears all other bits, including RTS. If RTS uses active-low polarity, it is now asserted for no reason. The TCRTLR bit is subsequently cleared by writing up->mcr to the MCR register. That variable is always zero, so the RTS bit is still cleared (incorrectly so if RTS is active-high). (up->mcr is not, as one might think, a cache of the MCR register's current value. Rather, it only caches a single bit of that register, the AFE bit. And it only does so if the UART supports the AFE bit, which OMAP does not. For details see serial8250_do_set_termios() and serial8250_do_set_mctrl().) Finally at the end of omap8250_restore_regs(), the MCR register is restored (and RTS deasserted) by a call to up->port.ops->set_mctrl() (which equals serial8250_set_mctrl()) and serial8250_em485_stop_tx(). So there's an RTS glitch between setting TCRTLR and calling serial8250_em485_stop_tx(). Avoid by using a read-modify-write when setting TCRTLR. While at it, drop a redundant initialization of up->mcr. As explained above, the variable isn't used by the driver and it is already initialized to zero because it is part of the static struct serial8250_ports[] declared in 8250_core.c. (Static structs are initialized to zero per section 6.7.8 nr. 10 of the C99 standard.) Cc: Jan Kiszka <jan.kiszka@xxxxxxxxxxx> Cc: Su Bao Cheng <baocheng.su@xxxxxxxxxxx> Tested-by: Matthias Schiffer <matthias.schiffer@xxxxxxxxxxxxxxx> Signed-off-by: Lukas Wunner <lukas@xxxxxxxxx> Link: https://lore.kernel.org/r/6554b0241a2c7fd50f32576fdbafed96709e11e8.1664278942.git.lukas@xxxxxxxxx Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx> Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx> --- drivers/tty/serial/8250/8250_omap.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c index 8cf4819312f5..b9352d3bb2ed 100644 --- a/drivers/tty/serial/8250/8250_omap.c +++ b/drivers/tty/serial/8250/8250_omap.c @@ -244,6 +244,7 @@ static void omap8250_restore_regs(struct uart_8250_port *up) { struct omap8250_priv *priv = up->port.private_data; struct uart_8250_dma *dma = up->dma; + u8 mcr = serial8250_in_MCR(up); if (dma && dma->tx_running) { /* @@ -260,7 +261,7 @@ static void omap8250_restore_regs(struct uart_8250_port *up) serial_out(up, UART_EFR, UART_EFR_ECB); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); - serial8250_out_MCR(up, UART_MCR_TCRTLR); + serial8250_out_MCR(up, mcr | UART_MCR_TCRTLR); serial_out(up, UART_FCR, up->fcr); omap8250_update_scr(up, priv); @@ -276,7 +277,8 @@ static void omap8250_restore_regs(struct uart_8250_port *up) serial_out(up, UART_LCR, 0); /* drop TCR + TLR access, we setup XON/XOFF later */ - serial8250_out_MCR(up, up->mcr); + serial8250_out_MCR(up, mcr); + serial_out(up, UART_IER, up->ier); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); @@ -585,7 +587,6 @@ static int omap_8250_startup(struct uart_port *port) pm_runtime_get_sync(port->dev); - up->mcr = 0; serial_out(up, UART_FCR, UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); serial_out(up, UART_LCR, UART_LCR_WLEN8); -- 2.35.1
