Re: [PATCH v3] spi: spi-imx: Fix spi_bus_clk if requested clock is higher than input clock

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 11/16/22 09:17, Frieder Schrempf wrote:
On 16.11.22 00:49, Marek Vasut wrote:
On 11/15/22 19:10, Frieder Schrempf wrote:
From: Frieder Schrempf <frieder.schrempf@xxxxxxxxxx>

In case the requested bus clock is higher than the input clock, the
correct
dividers (pre = 0, post = 0) are returned from mx51_ecspi_clkdiv(), but
*fres is left uninitialized and therefore contains an arbitrary value.

This causes trouble for the recently introduced PIO polling feature as
the
value in spi_imx->spi_bus_clk is used there to calculate for which
transfers to enable PIO polling.

Fix this by setting *fres even if no clock dividers are in use.

This issue was observed on Kontron BL i.MX8MM with an SPI peripheral
clock set
to 50 MHz by default and a requested SPI bus clock of 80 MHz for the
SPI NOR
flash.

With the fix applied the debug message from mx51_ecspi_clkdiv() now
prints the
following:

spi_imx 30820000.spi: mx51_ecspi_clkdiv: fin: 50000000, fspi: 50000000,
post: 0, pre: 0

Fixes: 6fd8b8503a0d ("spi: spi-imx: Fix out-of-order CS/SCLK operation
at low speeds")
Fixes: 07e759387788 ("spi: spi-imx: add PIO polling support")
Cc: Marc Kleine-Budde <mkl@xxxxxxxxxxxxxx>
Cc: David Jander <david@xxxxxxxxxxx>
Cc: Fabio Estevam <festevam@xxxxxxxxx>
Cc: Mark Brown <broonie@xxxxxxxxxx>
Cc: Marek Vasut <marex@xxxxxxx>
Cc: stable@xxxxxxxxxxxxxxx
Signed-off-by: Frieder Schrempf <frieder.schrempf@xxxxxxxxxx>
Tested-by: Fabio Estevam <festevam@xxxxxxxxx>
---

Changes for v3:

* Add back the Fixes tag for commit 6fd8b8503a0d
* Add Fabio's Tested-by (Thanks!)

Changes for v2:

* Remove the reference and the Fixes tag for commit 6fd8b8503a0d as it is
    incorrect.
---
   drivers/spi/spi-imx.c | 3 +--
   1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
index 30d82cc7300b..468ce0a2b282 100644
--- a/drivers/spi/spi-imx.c
+++ b/drivers/spi/spi-imx.c
@@ -444,8 +444,7 @@ static unsigned int mx51_ecspi_clkdiv(struct
spi_imx_data *spi_imx,
       unsigned int pre, post;
       unsigned int fin = spi_imx->spi_clk;
   -    if (unlikely(fspi > fin))
-        return 0;
+    fspi = min(fspi, fin);
         post = fls(fin) - fls(fspi);
       if (fin > fspi << post)

Can you also test the SPI flash at some 100 kHz, just to see whether it
still works properly ? (to retain behavior fixed first in 6fd8b8503a0dc
("spi: spi-imx: Fix out-of-order CS/SCLK operation at low speeds") )

The fix here does look fine by me however.

I successfully tested at 100 kHZ SPI bus clock. As in this case fspi is
lower than fin, the patch doesn't change anything in the code path and
therefore the behavior introduced in 6fd8b8503a0dc stays the same as
without the patch.

Acked-by: Marek Vasut <marex@xxxxxxx>

Thanks for the extra check !



[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux