From: Thinh Nguyen <Thinh.Nguyen@xxxxxxxxxxxx> [ Upstream commit 861c010a2ee1bc4a66d23f0da4aa22e75d8eaa24 ] Move soft-disconnect sequence out of dwc3_gadget_pullup(). No functional change here. Signed-off-by: Thinh Nguyen <Thinh.Nguyen@xxxxxxxxxxxx> Link: https://lore.kernel.org/r/4c0f259b17d95acaaa931f90276683a48a32fe22.1650593829.git.Thinh.Nguyen@xxxxxxxxxxxx Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx> Stable-dep-of: 040f2dbd2010 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop") Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx> --- drivers/usb/dwc3/gadget.c | 65 ++++++++++++++++++++++----------------- 1 file changed, 36 insertions(+), 29 deletions(-) diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c index 61499b657129..cdc03ee439f8 100644 --- a/drivers/usb/dwc3/gadget.c +++ b/drivers/usb/dwc3/gadget.c @@ -2435,6 +2435,40 @@ static void dwc3_gadget_disable_irq(struct dwc3 *dwc); static void __dwc3_gadget_stop(struct dwc3 *dwc); static int __dwc3_gadget_start(struct dwc3 *dwc); +static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc) +{ + u32 count; + + dwc->connected = false; + + /* + * In the Synopsys DesignWare Cores USB3 Databook Rev. 3.30a + * Section 4.1.8 Table 4-7, it states that for a device-initiated + * disconnect, the SW needs to ensure that it sends "a DEPENDXFER + * command for any active transfers" before clearing the RunStop + * bit. + */ + dwc3_stop_active_transfers(dwc); + __dwc3_gadget_stop(dwc); + + /* + * In the Synopsys DesignWare Cores USB3 Databook Rev. 3.30a + * Section 1.3.4, it mentions that for the DEVCTRLHLT bit, the + * "software needs to acknowledge the events that are generated + * (by writing to GEVNTCOUNTn) while it is waiting for this bit + * to be set to '1'." + */ + count = dwc3_readl(dwc->regs, DWC3_GEVNTCOUNT(0)); + count &= DWC3_GEVNTCOUNT_MASK; + if (count > 0) { + dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), count); + dwc->ev_buf->lpos = (dwc->ev_buf->lpos + count) % + dwc->ev_buf->length; + } + + return dwc3_gadget_run_stop(dwc, false, false); +} + static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on) { struct dwc3 *dwc = gadget_to_dwc(g); @@ -2491,33 +2525,7 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on) spin_lock_irqsave(&dwc->lock, flags); if (!is_on) { - u32 count; - - dwc->connected = false; - /* - * In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a - * Section 4.1.8 Table 4-7, it states that for a device-initiated - * disconnect, the SW needs to ensure that it sends "a DEPENDXFER - * command for any active transfers" before clearing the RunStop - * bit. - */ - dwc3_stop_active_transfers(dwc); - __dwc3_gadget_stop(dwc); - - /* - * In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a - * Section 1.3.4, it mentions that for the DEVCTRLHLT bit, the - * "software needs to acknowledge the events that are generated - * (by writing to GEVNTCOUNTn) while it is waiting for this bit - * to be set to '1'." - */ - count = dwc3_readl(dwc->regs, DWC3_GEVNTCOUNT(0)); - count &= DWC3_GEVNTCOUNT_MASK; - if (count > 0) { - dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), count); - dwc->ev_buf->lpos = (dwc->ev_buf->lpos + count) % - dwc->ev_buf->length; - } + ret = dwc3_gadget_soft_disconnect(dwc); } else { /* * In the Synopsys DWC_usb31 1.90a programming guide section @@ -2531,9 +2539,8 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on) dwc3_event_buffers_setup(dwc); __dwc3_gadget_start(dwc); + ret = dwc3_gadget_run_stop(dwc, true, false); } - - ret = dwc3_gadget_run_stop(dwc, is_on, false); spin_unlock_irqrestore(&dwc->lock, flags); enable_irq(dwc->irq_gadget); -- 2.35.1
