From: Pali Rohár <pali@xxxxxxxxxx>
commit 0c551abfa004ce154d487d91777bf221c808a64f upstream.
By default old pre-3.0 Freescale PCIe controllers reports invalid PCI Class
Code 0x0b20 for PCIe Root Port. It can be seen by lspci -b output on P2020
board which has this pre-3.0 controller:
$ lspci -bvnn
00:00.0 Power PC [0b20]: Freescale Semiconductor Inc P2020E [1957:0070] (rev 21)
!!! Invalid class 0b20 for header type 01
Capabilities: [4c] Express Root Port (Slot-), MSI 00
Fix this issue by programming correct PCI Class Code 0x0604 for PCIe Root
Port to the Freescale specific PCIe register 0x474.
With this change lspci -b output is:
$ lspci -bvnn
00:00.0 PCI bridge [0604]: Freescale Semiconductor Inc P2020E [1957:0070] (rev 21) (prog-if 00 [Normal decode])
Capabilities: [4c] Express Root Port (Slot-), MSI 00
Without any "Invalid class" error. So class code was properly reflected
into standard (read-only) PCI register 0x08.
Same fix is already implemented in U-Boot pcie_fsl.c driver in commit:
http://source.denx.de/u-boot/u-boot/-/commit/d18d06ac35229345a0af80977a408cfbe1d1015b
Fix activated by U-Boot stay active also after booting Linux kernel.
But boards which use older U-Boot version without that fix are affected and
still require this fix.
So implement this class code fix also in kernel fsl_pci.c driver.
Cc: stable@xxxxxxxxxxxxxxx
Signed-off-by: Pali Rohár <pali@xxxxxxxxxx>
Signed-off-by: Michael Ellerman <mpe@xxxxxxxxxxxxxx>
Link: https://lore.kernel.org/r/20220706101043.4867-1-pali@xxxxxxxxxx
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
arch/powerpc/sysdev/fsl_pci.c | 8 ++++++++
arch/powerpc/sysdev/fsl_pci.h | 1 +
2 files changed, 9 insertions(+)
--- a/arch/powerpc/sysdev/fsl_pci.c
+++ b/arch/powerpc/sysdev/fsl_pci.c
@@ -520,6 +520,7 @@ int fsl_add_bridge(struct platform_devic
struct resource rsrc;
const int *bus_range;
u8 hdr_type, progif;
+ u32 class_code;
struct device_node *dev;
struct ccsr_pci __iomem *pci;
u16 temp;
@@ -593,6 +594,13 @@ int fsl_add_bridge(struct platform_devic
PPC_INDIRECT_TYPE_SURPRESS_PRIMARY_BUS;
if (fsl_pcie_check_link(hose))
hose->indirect_type |= PPC_INDIRECT_TYPE_NO_PCIE_LINK;
+ /* Fix Class Code to PCI_CLASS_BRIDGE_PCI_NORMAL for pre-3.0 controller */
+ if (in_be32(&pci->block_rev1) < PCIE_IP_REV_3_0) {
+ early_read_config_dword(hose, 0, 0, PCIE_FSL_CSR_CLASSCODE, &class_code);
+ class_code &= 0xff;
+ class_code |= PCI_CLASS_BRIDGE_PCI_NORMAL << 8;
+ early_write_config_dword(hose, 0, 0, PCIE_FSL_CSR_CLASSCODE, class_code);
+ }
} else {
/*
* Set PBFR(PCI Bus Function Register)[10] = 1 to
--- a/arch/powerpc/sysdev/fsl_pci.h
+++ b/arch/powerpc/sysdev/fsl_pci.h
@@ -18,6 +18,7 @@ struct platform_device;
#define PCIE_LTSSM 0x0404 /* PCIE Link Training and Status */
#define PCIE_LTSSM_L0 0x16 /* L0 state */
+#define PCIE_FSL_CSR_CLASSCODE 0x474 /* FSL GPEX CSR */
#define PCIE_IP_REV_2_2 0x02080202 /* PCIE IP block version Rev2.2 */
#define PCIE_IP_REV_3_0 0x02080300 /* PCIE IP block version Rev3.0 */
#define PIWAR_EN 0x80000000 /* Enable */
