From: Viorel Suman <viorel.suman@xxxxxxx>
[ Upstream commit d7cd5e06c9dd70a82f1461c7b5f676bc03f5cd61 ]
Before 7beecaf7d507b ("net: phy: at803x: improve the WOL feature") patch
"at803x_get_wol" implementation used AT803X_INTR_ENABLE_WOL value to set
WAKE_MAGIC flag, and now AT803X_WOL_EN value is used for the same purpose.
The problem here is that the values of these two bits are different after
hardware reset: AT803X_INTR_ENABLE_WOL=0 after hardware reset, but
AT803X_WOL_EN=1. So now, if called right after boot, "at803x_get_wol" will
set WAKE_MAGIC flag, even if WOL function is not enabled by calling
"at803x_set_wol" function. The patch disables WOL function on probe thus
the behavior is consistent.
Fixes: 7beecaf7d507b ("net: phy: at803x: improve the WOL feature")
Signed-off-by: Viorel Suman <viorel.suman@xxxxxxx>
Link: https://lore.kernel.org/r/20220527084935.235274-1-viorel.suman@xxxxxxxxxxx
Signed-off-by: Jakub Kicinski <kuba@xxxxxxxxxx>
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
---
drivers/net/phy/at803x.c | 33 ++++++++++++++++++++++-----------
1 file changed, 22 insertions(+), 11 deletions(-)
diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index 73926006d319..6a467e7817a6 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -433,20 +433,21 @@ static void at803x_context_restore(struct phy_device *phydev,
static int at803x_set_wol(struct phy_device *phydev,
struct ethtool_wolinfo *wol)
{
- struct net_device *ndev = phydev->attached_dev;
- const u8 *mac;
int ret, irq_enabled;
- unsigned int i;
- static const unsigned int offsets[] = {
- AT803X_LOC_MAC_ADDR_32_47_OFFSET,
- AT803X_LOC_MAC_ADDR_16_31_OFFSET,
- AT803X_LOC_MAC_ADDR_0_15_OFFSET,
- };
-
- if (!ndev)
- return -ENODEV;
if (wol->wolopts & WAKE_MAGIC) {
+ struct net_device *ndev = phydev->attached_dev;
+ const u8 *mac;
+ unsigned int i;
+ static const unsigned int offsets[] = {
+ AT803X_LOC_MAC_ADDR_32_47_OFFSET,
+ AT803X_LOC_MAC_ADDR_16_31_OFFSET,
+ AT803X_LOC_MAC_ADDR_0_15_OFFSET,
+ };
+
+ if (!ndev)
+ return -ENODEV;
+
mac = (const u8 *) ndev->dev_addr;
if (!is_valid_ether_addr(mac))
@@ -857,6 +858,9 @@ static int at803x_probe(struct phy_device *phydev)
if (phydev->drv->phy_id == ATH8031_PHY_ID) {
int ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG);
int mode_cfg;
+ struct ethtool_wolinfo wol = {
+ .wolopts = 0,
+ };
if (ccr < 0)
goto err;
@@ -872,6 +876,13 @@ static int at803x_probe(struct phy_device *phydev)
priv->is_fiber = true;
break;
}
+
+ /* Disable WOL by default */
+ ret = at803x_set_wol(phydev, &wol);
+ if (ret < 0) {
+ phydev_err(phydev, "failed to disable WOL on probe: %d\n", ret);
+ goto err;
+ }
}
return 0;
--
2.35.1
