From: Jagan Teki <jagan@xxxxxxxxxxxxxxxxxxxx>
[ Upstream commit 3dbc84a595d17f64f14fcea00120d31e33e98880 ]
Existing HPD enablement logic is not compatible with ADV7535
bridge, thus any runtime plug-in of HDMI cable is not working
on these bridge designs.
Unlike other ADV7511 family of bridges, the ADV7535 require
HPD_OVERRIDE bit to set and reset for proper handling of HPD
functionality.
Fix it.
Fixes: 8501fe4b14a3 ("drm: bridge: adv7511: Add support for ADV7535")
Signed-off-by: Jagan Teki <jagan@xxxxxxxxxxxxxxxxxxxx>
Signed-off-by: Robert Foss <robert.foss@xxxxxxxxxx>
Link: https://patchwork.freedesktop.org/patch/msgid/20220109172949.168167-1-jagan@xxxxxxxxxxxxxxxxxxxx
Reviewed-by: Robert Foss <robert.foss@xxxxxxxxxx>
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
---
drivers/gpu/drm/bridge/adv7511/adv7511.h | 1 +
drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 29 +++++++++++++++-----
2 files changed, 23 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511.h b/drivers/gpu/drm/bridge/adv7511/adv7511.h
index 592ecfcf00ca..6a882891d91c 100644
--- a/drivers/gpu/drm/bridge/adv7511/adv7511.h
+++ b/drivers/gpu/drm/bridge/adv7511/adv7511.h
@@ -169,6 +169,7 @@
#define ADV7511_PACKET_ENABLE_SPARE2 BIT(1)
#define ADV7511_PACKET_ENABLE_SPARE1 BIT(0)
+#define ADV7535_REG_POWER2_HPD_OVERRIDE BIT(6)
#define ADV7511_REG_POWER2_HPD_SRC_MASK 0xc0
#define ADV7511_REG_POWER2_HPD_SRC_BOTH 0x00
#define ADV7511_REG_POWER2_HPD_SRC_HPD 0x40
diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
index f8e5da148599..77118c3395bf 100644
--- a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
+++ b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
@@ -351,11 +351,17 @@ static void __adv7511_power_on(struct adv7511 *adv7511)
* from standby or are enabled. When the HPD goes low the adv7511 is
* reset and the outputs are disabled which might cause the monitor to
* go to standby again. To avoid this we ignore the HPD pin for the
- * first few seconds after enabling the output.
+ * first few seconds after enabling the output. On the other hand
+ * adv7535 require to enable HPD Override bit for proper HPD.
*/
- regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
- ADV7511_REG_POWER2_HPD_SRC_MASK,
- ADV7511_REG_POWER2_HPD_SRC_NONE);
+ if (adv7511->type == ADV7535)
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
+ ADV7535_REG_POWER2_HPD_OVERRIDE,
+ ADV7535_REG_POWER2_HPD_OVERRIDE);
+ else
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
+ ADV7511_REG_POWER2_HPD_SRC_MASK,
+ ADV7511_REG_POWER2_HPD_SRC_NONE);
}
static void adv7511_power_on(struct adv7511 *adv7511)
@@ -375,6 +381,10 @@ static void adv7511_power_on(struct adv7511 *adv7511)
static void __adv7511_power_off(struct adv7511 *adv7511)
{
/* TODO: setup additional power down modes */
+ if (adv7511->type == ADV7535)
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
+ ADV7535_REG_POWER2_HPD_OVERRIDE, 0);
+
regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
ADV7511_POWER_POWER_DOWN,
ADV7511_POWER_POWER_DOWN);
@@ -672,9 +682,14 @@ adv7511_detect(struct adv7511 *adv7511, struct drm_connector *connector)
status = connector_status_disconnected;
} else {
/* Renable HPD sensing */
- regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
- ADV7511_REG_POWER2_HPD_SRC_MASK,
- ADV7511_REG_POWER2_HPD_SRC_BOTH);
+ if (adv7511->type == ADV7535)
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
+ ADV7535_REG_POWER2_HPD_OVERRIDE,
+ ADV7535_REG_POWER2_HPD_OVERRIDE);
+ else
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
+ ADV7511_REG_POWER2_HPD_SRC_MASK,
+ ADV7511_REG_POWER2_HPD_SRC_BOTH);
}
adv7511->status = status;
--
2.34.1
