From: Arnd Bergmann <arnd@xxxxxxxx> Naresh and Antonio ran into a build failure with latest Debian armhf compilers, with lots of output like tmp/ccY3nOAs.s:2215: Error: selected processor does not support `cpsid i' in ARM mode As it turns out, $(cc-option) fails early here when the FPU is not selected before CPU architecture is selected, as the compiler option check runs before enabling -msoft-float, which causes a problem when testing a target architecture level without an FPU: cc1: error: '-mfloat-abi=hard': selected architecture lacks an FPU Passing e.g. -march=armv6k+fp in place of -march=armv6k would avoid this issue, but the fallback logic is already broken because all supported compilers (gcc-5 and higher) are much more recent than these options, and building with -march=armv5t as a fallback no longer works. The best way forward that I see is to just remove all the checks, which also has the nice side-effect of slightly improving the startup time for 'make'. The -mtune=marvell-f option was apparently never supported by any mainline compiler, and the custom Codesourcery gcc build that did support is now too old to build kernels, so just use -mtune=xscale unconditionally for those. This should be safe to apply on all stable kernels, and will be required in order to keep building them with gcc-11 and higher. Reported-by: Antonio Terceiro <antonio.terceiro@xxxxxxxxxx> Reported-by: Naresh Kamboju <naresh.kamboju@xxxxxxxxxx> Reported-by: Sebastian Andrzej Siewior <sebastian@xxxxxxxxxxxxx> Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=996419 Cc: Matthias Klose <doko@xxxxxxxxxx> Cc: stable@xxxxxxxxxxxxxxx Signed-off-by: Arnd Bergmann <arnd@xxxxxxxx> --- arch/arm/Makefile | 22 +++++++++++----------- 1 file changed, 11 insertions(+), 11 deletions(-) diff --git a/arch/arm/Makefile b/arch/arm/Makefile index 847c31e7c368..fa45837b8065 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -60,15 +60,15 @@ KBUILD_CFLAGS += $(call cc-option,-fno-ipa-sra) # Note that GCC does not numerically define an architecture version # macro, but instead defines a whole series of macros which makes # testing for a specific architecture or later rather impossible. -arch-$(CONFIG_CPU_32v7M) =-D__LINUX_ARM_ARCH__=7 -march=armv7-m -Wa,-march=armv7-m -arch-$(CONFIG_CPU_32v7) =-D__LINUX_ARM_ARCH__=7 $(call cc-option,-march=armv7-a,-march=armv5t -Wa$(comma)-march=armv7-a) -arch-$(CONFIG_CPU_32v6) =-D__LINUX_ARM_ARCH__=6 $(call cc-option,-march=armv6,-march=armv5t -Wa$(comma)-march=armv6) +arch-$(CONFIG_CPU_32v7M) =-D__LINUX_ARM_ARCH__=7 -march=armv7-m +arch-$(CONFIG_CPU_32v7) =-D__LINUX_ARM_ARCH__=7 -march=armv7-a +arch-$(CONFIG_CPU_32v6) =-D__LINUX_ARM_ARCH__=6 -march=armv6 # Only override the compiler option if ARMv6. The ARMv6K extensions are # always available in ARMv7 ifeq ($(CONFIG_CPU_32v6),y) -arch-$(CONFIG_CPU_32v6K) =-D__LINUX_ARM_ARCH__=6 $(call cc-option,-march=armv6k,-march=armv5t -Wa$(comma)-march=armv6k) +arch-$(CONFIG_CPU_32v6K) =-D__LINUX_ARM_ARCH__=6 -march=armv6k endif -arch-$(CONFIG_CPU_32v5) =-D__LINUX_ARM_ARCH__=5 $(call cc-option,-march=armv5te,-march=armv4t) +arch-$(CONFIG_CPU_32v5) =-D__LINUX_ARM_ARCH__=5 -march=armv5te arch-$(CONFIG_CPU_32v4T) =-D__LINUX_ARM_ARCH__=4 -march=armv4t arch-$(CONFIG_CPU_32v4) =-D__LINUX_ARM_ARCH__=4 -march=armv4 arch-$(CONFIG_CPU_32v3) =-D__LINUX_ARM_ARCH__=3 -march=armv3m @@ -82,7 +82,7 @@ tune-$(CONFIG_CPU_ARM720T) =-mtune=arm7tdmi tune-$(CONFIG_CPU_ARM740T) =-mtune=arm7tdmi tune-$(CONFIG_CPU_ARM9TDMI) =-mtune=arm9tdmi tune-$(CONFIG_CPU_ARM940T) =-mtune=arm9tdmi -tune-$(CONFIG_CPU_ARM946E) =$(call cc-option,-mtune=arm9e,-mtune=arm9tdmi) +tune-$(CONFIG_CPU_ARM946E) =-mtune=arm9e tune-$(CONFIG_CPU_ARM920T) =-mtune=arm9tdmi tune-$(CONFIG_CPU_ARM922T) =-mtune=arm9tdmi tune-$(CONFIG_CPU_ARM925T) =-mtune=arm9tdmi @@ -90,11 +90,11 @@ tune-$(CONFIG_CPU_ARM926T) =-mtune=arm9tdmi tune-$(CONFIG_CPU_FA526) =-mtune=arm9tdmi tune-$(CONFIG_CPU_SA110) =-mtune=strongarm110 tune-$(CONFIG_CPU_SA1100) =-mtune=strongarm1100 -tune-$(CONFIG_CPU_XSCALE) =$(call cc-option,-mtune=xscale,-mtune=strongarm110) -Wa,-mcpu=xscale -tune-$(CONFIG_CPU_XSC3) =$(call cc-option,-mtune=xscale,-mtune=strongarm110) -Wa,-mcpu=xscale -tune-$(CONFIG_CPU_FEROCEON) =$(call cc-option,-mtune=marvell-f,-mtune=xscale) -tune-$(CONFIG_CPU_V6) =$(call cc-option,-mtune=arm1136j-s,-mtune=strongarm) -tune-$(CONFIG_CPU_V6K) =$(call cc-option,-mtune=arm1136j-s,-mtune=strongarm) +tune-$(CONFIG_CPU_XSCALE) =-mtune=xscale +tune-$(CONFIG_CPU_XSC3) =-mtune=xscale +tune-$(CONFIG_CPU_FEROCEON) =-mtune=xscale +tune-$(CONFIG_CPU_V6) =-mtune=arm1136j-s +tune-$(CONFIG_CPU_V6K) =-mtune=arm1136j-s # Evaluate tune cc-option calls now tune-y := $(tune-y) -- 2.29.2
