[PATCH 5.10 069/103] gpio: pca953x: Improve bias setting

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>

commit 55a9968c7e139209a9e93d4ca4321731bea5fc95 upstream.

The commit 15add06841a3 ("gpio: pca953x: add ->set_config implementation")
introduced support for bias setting. However this, due to being half-baked,
brought potential issues:
 - the turning bias via disabling makes the pin floating for a while;
 - once enabled, bias can't be disabled.

Fix all these by adding support for bias disabling and move the disabling
part under the corresponding conditional.

While at it, add support for default setting, since it's cheap to add.

Fixes: 15add06841a3 ("gpio: pca953x: add ->set_config implementation")
Cc: Thomas Petazzoni <thomas.petazzoni@xxxxxxxxxxx>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
Signed-off-by: Bartosz Golaszewski <brgl@xxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
 drivers/gpio/gpio-pca953x.c |   16 +++++++++-------
 1 file changed, 9 insertions(+), 7 deletions(-)

--- a/drivers/gpio/gpio-pca953x.c
+++ b/drivers/gpio/gpio-pca953x.c
@@ -558,21 +558,21 @@ static int pca953x_gpio_set_pull_up_down
 
 	mutex_lock(&chip->i2c_lock);
 
-	/* Disable pull-up/pull-down */
-	ret = regmap_write_bits(chip->regmap, pull_en_reg, bit, 0);
-	if (ret)
-		goto exit;
-
 	/* Configure pull-up/pull-down */
 	if (config == PIN_CONFIG_BIAS_PULL_UP)
 		ret = regmap_write_bits(chip->regmap, pull_sel_reg, bit, bit);
 	else if (config == PIN_CONFIG_BIAS_PULL_DOWN)
 		ret = regmap_write_bits(chip->regmap, pull_sel_reg, bit, 0);
+	else
+		ret = 0;
 	if (ret)
 		goto exit;
 
-	/* Enable pull-up/pull-down */
-	ret = regmap_write_bits(chip->regmap, pull_en_reg, bit, bit);
+	/* Disable/Enable pull-up/pull-down */
+	if (config == PIN_CONFIG_BIAS_DISABLE)
+		ret = regmap_write_bits(chip->regmap, pull_en_reg, bit, 0);
+	else
+		ret = regmap_write_bits(chip->regmap, pull_en_reg, bit, bit);
 
 exit:
 	mutex_unlock(&chip->i2c_lock);
@@ -586,7 +586,9 @@ static int pca953x_gpio_set_config(struc
 
 	switch (pinconf_to_config_param(config)) {
 	case PIN_CONFIG_BIAS_PULL_UP:
+	case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT:
 	case PIN_CONFIG_BIAS_PULL_DOWN:
+	case PIN_CONFIG_BIAS_DISABLE:
 		return pca953x_gpio_set_pull_up_down(chip, offset, config);
 	default:
 		return -ENOTSUPP;





[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux