[PATCH 5.12 204/296] scsi: pm80xx: Fix drives missing during rmmod/insmod loop

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Ajish Koshy <ajish.koshy@xxxxxxxxxxxxx>

[ Upstream commit d1acd81bd6eb685aa9fef25624fb36d297f6404e ]

When driver is loaded after rmmod some drives are not showing up during
discovery.

SATA drives are directly attached to the controller connected phys.  During
device discovery, the IDENTIFY command (qc timeout (cmd 0xec)) is timing out
during revalidation. This will trigger abort from host side and controller
successfully aborts the command and returns success. Post this successful
abort response ATA library decides to mark the disk as NODEV.

To overcome this, inside pm8001_scan_start() after phy_start() call, add get
start response and wait for few milliseconds to trigger next phy start.
This millisecond delay will give sufficient time for the controller state
machine to accept next phy start.

Link: https://lore.kernel.org/r/20210505120103.24497-1-ajish.koshy@xxxxxxxxxxxxx
Signed-off-by: Ajish Koshy <ajish.koshy@xxxxxxxxxxxxx>
Signed-off-by: Viswas G <viswas.g@xxxxxxxxxxxxx>
Signed-off-by: Martin K. Petersen <martin.petersen@xxxxxxxxxx>
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
---
 drivers/scsi/pm8001/pm8001_hwi.c  | 10 ++++++----
 drivers/scsi/pm8001/pm8001_init.c |  2 +-
 drivers/scsi/pm8001/pm8001_sas.c  |  7 ++++++-
 drivers/scsi/pm8001/pm80xx_hwi.c  | 12 ++++++------
 4 files changed, 19 insertions(+), 12 deletions(-)

diff --git a/drivers/scsi/pm8001/pm8001_hwi.c b/drivers/scsi/pm8001/pm8001_hwi.c
index 1b1a57f46989..c2a38a172904 100644
--- a/drivers/scsi/pm8001/pm8001_hwi.c
+++ b/drivers/scsi/pm8001/pm8001_hwi.c
@@ -3709,11 +3709,13 @@ static int mpi_hw_event(struct pm8001_hba_info *pm8001_ha, void* piomb)
 	case HW_EVENT_PHY_START_STATUS:
 		pm8001_dbg(pm8001_ha, MSG, "HW_EVENT_PHY_START_STATUS status = %x\n",
 			   status);
-		if (status == 0) {
+		if (status == 0)
 			phy->phy_state = 1;
-			if (pm8001_ha->flags == PM8001F_RUN_TIME &&
-					phy->enable_completion != NULL)
-				complete(phy->enable_completion);
+
+		if (pm8001_ha->flags == PM8001F_RUN_TIME &&
+				phy->enable_completion != NULL) {
+			complete(phy->enable_completion);
+			phy->enable_completion = NULL;
 		}
 		break;
 	case HW_EVENT_SAS_PHY_UP:
diff --git a/drivers/scsi/pm8001/pm8001_init.c b/drivers/scsi/pm8001/pm8001_init.c
index bd626ef876da..4f3ec2bba8c9 100644
--- a/drivers/scsi/pm8001/pm8001_init.c
+++ b/drivers/scsi/pm8001/pm8001_init.c
@@ -1144,8 +1144,8 @@ static int pm8001_pci_probe(struct pci_dev *pdev,
 		goto err_out_shost;
 	}
 	list_add_tail(&pm8001_ha->list, &hba_list);
-	scsi_scan_host(pm8001_ha->shost);
 	pm8001_ha->flags = PM8001F_RUN_TIME;
+	scsi_scan_host(pm8001_ha->shost);
 	return 0;
 
 err_out_shost:
diff --git a/drivers/scsi/pm8001/pm8001_sas.c b/drivers/scsi/pm8001/pm8001_sas.c
index a98d4496ff8b..0a637609504e 100644
--- a/drivers/scsi/pm8001/pm8001_sas.c
+++ b/drivers/scsi/pm8001/pm8001_sas.c
@@ -264,12 +264,17 @@ void pm8001_scan_start(struct Scsi_Host *shost)
 	int i;
 	struct pm8001_hba_info *pm8001_ha;
 	struct sas_ha_struct *sha = SHOST_TO_SAS_HA(shost);
+	DECLARE_COMPLETION_ONSTACK(completion);
 	pm8001_ha = sha->lldd_ha;
 	/* SAS_RE_INITIALIZATION not available in SPCv/ve */
 	if (pm8001_ha->chip_id == chip_8001)
 		PM8001_CHIP_DISP->sas_re_init_req(pm8001_ha);
-	for (i = 0; i < pm8001_ha->chip->n_phy; ++i)
+	for (i = 0; i < pm8001_ha->chip->n_phy; ++i) {
+		pm8001_ha->phy[i].enable_completion = &completion;
 		PM8001_CHIP_DISP->phy_start_req(pm8001_ha, i);
+		wait_for_completion(&completion);
+		msleep(300);
+	}
 }
 
 int pm8001_scan_finished(struct Scsi_Host *shost, unsigned long time)
diff --git a/drivers/scsi/pm8001/pm80xx_hwi.c b/drivers/scsi/pm8001/pm80xx_hwi.c
index c6b0834e3806..5de7adfabd57 100644
--- a/drivers/scsi/pm8001/pm80xx_hwi.c
+++ b/drivers/scsi/pm8001/pm80xx_hwi.c
@@ -3485,13 +3485,13 @@ static int mpi_phy_start_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
 	pm8001_dbg(pm8001_ha, INIT,
 		   "phy start resp status:0x%x, phyid:0x%x\n",
 		   status, phy_id);
-	if (status == 0) {
+	if (status == 0)
 		phy->phy_state = PHY_LINK_DOWN;
-		if (pm8001_ha->flags == PM8001F_RUN_TIME &&
-				phy->enable_completion != NULL) {
-			complete(phy->enable_completion);
-			phy->enable_completion = NULL;
-		}
+
+	if (pm8001_ha->flags == PM8001F_RUN_TIME &&
+			phy->enable_completion != NULL) {
+		complete(phy->enable_completion);
+		phy->enable_completion = NULL;
 	}
 	return 0;
 
-- 
2.30.2






[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux