From: Linus Walleij <linus.walleij@xxxxxxxxxx>
[ Upstream commit aeceecd40d94ed3c00bfe1cfe59dd1bfac2fc6fe ]
The TVK1281618 R3 sensors are different from the R2 board,
some incorrectness is fixed and some new sensors added, we
also rename the nodes appropriately with accelerometer@
etc.
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
---
arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi | 73 +++++++++++++------
1 file changed, 50 insertions(+), 23 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi
index cb3677f0a1cb..b580397ede83 100644
--- a/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi
+++ b/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi
@@ -8,37 +8,43 @@
/ {
soc {
i2c@80128000 {
- /* Marked:
- * 129
- * M35
- * L3GD20
- */
- l3gd20@6a {
- /* Gyroscope */
- compatible = "st,l3gd20";
- status = "disabled";
+ accelerometer@19 {
+ compatible = "st,lsm303dlhc-accel";
st,drdy-int-pin = <1>;
- drive-open-drain;
- reg = <0x6a>; // 0x6a or 0x6b
+ reg = <0x19>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <18 IRQ_TYPE_EDGE_RISING>,
+ <19 IRQ_TYPE_EDGE_RISING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&accel_tvk_mode>;
};
- /*
- * Marked:
- * 2122
- * C3H
- * DQEEE
- * LIS3DH?
- */
- lis3dh@18 {
- /* Accelerometer */
- compatible = "st,lis3dh-accel";
+ magnetometer@1e {
+ compatible = "st,lsm303dlm-magn";
st,drdy-int-pin = <1>;
- reg = <0x18>;
+ reg = <0x1e>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
+ // This interrupt is not properly working with the driver
+ // interrupt-parent = <&gpio1>;
+ // interrupts = <0 IRQ_TYPE_EDGE_RISING>;
pinctrl-names = "default";
- pinctrl-0 = <&accel_tvk_mode>;
+ pinctrl-0 = <&magn_tvk_mode>;
+ };
+ gyroscope@68 {
+ /* Gyroscope */
+ compatible = "st,l3g4200d-gyro";
+ reg = <0x68>;
+ vdd-supply = <&ab8500_ldo_aux1_reg>;
+ vddio-supply = <&db8500_vsmps2_reg>;
+ };
+ pressure@5c {
+ /* Barometer/pressure sensor */
+ compatible = "st,lps001wp-press";
+ reg = <0x5c>;
+ vdd-supply = <&ab8500_ldo_aux1_reg>;
+ vddio-supply = <&db8500_vsmps2_reg>;
};
};
@@ -54,5 +60,26 @@
};
};
};
+
+ pinctrl {
+ accelerometer {
+ accel_tvk_mode: accel_tvk {
+ /* Accelerometer interrupt lines 1 & 2 */
+ tvk_cfg {
+ pins = "GPIO82_C1", "GPIO83_D3";
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+ magnetometer {
+ magn_tvk_mode: magn_tvk {
+ /* GPIO 32 used for DRDY, pull this down */
+ tvk_cfg {
+ pins = "GPIO32_V2";
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+ };
};
};
--
2.30.2
