commit 1fe976d308acb6374c899a4ee8025a0a016e453e upstream.
Since commit fee2d546414d ("net: phy: marvell: mv88e6390 temperature
sensor reading"), Linux reports the temperature of Topaz hwmon as
constant -75°C.
This is because switches from the Topaz family (88E6141 / 88E6341) have
the address of the temperature sensor register different from Peridot.
This address is instead compatible with 88E1510 PHYs, as was used for
Topaz before the above mentioned commit.
Create a new mapping table between switch family and PHY ID for families
which don't have a model number. And define PHY IDs for Topaz and Peridot
families.
Create a new PHY ID and a new PHY driver for Topaz's internal PHY.
The only difference from Peridot's PHY driver is the HWMON probing
method.
Prior this change Topaz's internal PHY is detected by kernel as:
PHY [...] driver [Marvell 88E6390] (irq=63)
And afterwards as:
PHY [...] driver [Marvell 88E6341 Family] (irq=63)
Signed-off-by: Pali Rohár <pali@xxxxxxxxxx>
BugLink: https://github.com/globalscaletechnologies/linux/issues/1
Fixes: fee2d546414d ("net: phy: marvell: mv88e6390 temperature sensor reading")
Reviewed-by: Marek Behún <kabel@xxxxxxxxxx>
Reviewed-by: Andrew Lunn <andrew@xxxxxxx>
Signed-off-by: David S. Miller <davem@xxxxxxxxxxxxx>
[pali: Backported to 5.10 version]
---
This patch is backported to 5.10 version. Tested on Turris Mox with Topaz switch.
---
drivers/net/dsa/mv88e6xxx/chip.c | 30 +++++++++++++----------------
drivers/net/phy/marvell.c | 33 +++++++++++++++++++++++++++++---
include/linux/marvell_phy.h | 5 +++--
3 files changed, 46 insertions(+), 22 deletions(-)
diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index 87160e723dfc..70ec17f3c300 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -2994,10 +2994,17 @@ static int mv88e6xxx_setup(struct dsa_switch *ds)
return err;
}
+/* prod_id for switch families which do not have a PHY model number */
+static const u16 family_prod_id_table[] = {
+ [MV88E6XXX_FAMILY_6341] = MV88E6XXX_PORT_SWITCH_ID_PROD_6341,
+ [MV88E6XXX_FAMILY_6390] = MV88E6XXX_PORT_SWITCH_ID_PROD_6390,
+};
+
static int mv88e6xxx_mdio_read(struct mii_bus *bus, int phy, int reg)
{
struct mv88e6xxx_mdio_bus *mdio_bus = bus->priv;
struct mv88e6xxx_chip *chip = mdio_bus->chip;
+ u16 prod_id;
u16 val;
int err;
@@ -3008,23 +3015,12 @@ static int mv88e6xxx_mdio_read(struct mii_bus *bus, int phy, int reg)
err = chip->info->ops->phy_read(chip, bus, phy, reg, &val);
mv88e6xxx_reg_unlock(chip);
- if (reg == MII_PHYSID2) {
- /* Some internal PHYs don't have a model number. */
- if (chip->info->family != MV88E6XXX_FAMILY_6165)
- /* Then there is the 6165 family. It gets is
- * PHYs correct. But it can also have two
- * SERDES interfaces in the PHY address
- * space. And these don't have a model
- * number. But they are not PHYs, so we don't
- * want to give them something a PHY driver
- * will recognise.
- *
- * Use the mv88e6390 family model number
- * instead, for anything which really could be
- * a PHY,
- */
- if (!(val & 0x3f0))
- val |= MV88E6XXX_PORT_SWITCH_ID_PROD_6390 >> 4;
+ /* Some internal PHYs don't have a model number. */
+ if (reg == MII_PHYSID2 && !(val & 0x3f0) &&
+ chip->info->family < ARRAY_SIZE(family_prod_id_table)) {
+ prod_id = family_prod_id_table[chip->info->family];
+ if (prod_id)
+ val |= prod_id >> 4;
}
return err ? err : val;
diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index 5dbdaf0f5f09..823a89354466 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -2913,9 +2913,35 @@ static struct phy_driver marvell_drivers[] = {
.get_stats = marvell_get_stats,
},
{
- .phy_id = MARVELL_PHY_ID_88E6390,
+ .phy_id = MARVELL_PHY_ID_88E6341_FAMILY,
.phy_id_mask = MARVELL_PHY_ID_MASK,
- .name = "Marvell 88E6390",
+ .name = "Marvell 88E6341 Family",
+ /* PHY_GBIT_FEATURES */
+ .flags = PHY_POLL_CABLE_TEST,
+ .probe = m88e1510_probe,
+ .config_init = marvell_config_init,
+ .config_aneg = m88e6390_config_aneg,
+ .read_status = marvell_read_status,
+ .ack_interrupt = marvell_ack_interrupt,
+ .config_intr = marvell_config_intr,
+ .did_interrupt = m88e1121_did_interrupt,
+ .resume = genphy_resume,
+ .suspend = genphy_suspend,
+ .read_page = marvell_read_page,
+ .write_page = marvell_write_page,
+ .get_sset_count = marvell_get_sset_count,
+ .get_strings = marvell_get_strings,
+ .get_stats = marvell_get_stats,
+ .get_tunable = m88e1540_get_tunable,
+ .set_tunable = m88e1540_set_tunable,
+ .cable_test_start = marvell_vct7_cable_test_start,
+ .cable_test_tdr_start = marvell_vct5_cable_test_tdr_start,
+ .cable_test_get_status = marvell_vct7_cable_test_get_status,
+ },
+ {
+ .phy_id = MARVELL_PHY_ID_88E6390_FAMILY,
+ .phy_id_mask = MARVELL_PHY_ID_MASK,
+ .name = "Marvell 88E6390 Family",
/* PHY_GBIT_FEATURES */
.flags = PHY_POLL_CABLE_TEST,
.probe = m88e6390_probe,
@@ -3001,7 +3027,8 @@ static struct mdio_device_id __maybe_unused marvell_tbl[] = {
{ MARVELL_PHY_ID_88E1540, MARVELL_PHY_ID_MASK },
{ MARVELL_PHY_ID_88E1545, MARVELL_PHY_ID_MASK },
{ MARVELL_PHY_ID_88E3016, MARVELL_PHY_ID_MASK },
- { MARVELL_PHY_ID_88E6390, MARVELL_PHY_ID_MASK },
+ { MARVELL_PHY_ID_88E6341_FAMILY, MARVELL_PHY_ID_MASK },
+ { MARVELL_PHY_ID_88E6390_FAMILY, MARVELL_PHY_ID_MASK },
{ MARVELL_PHY_ID_88E1340S, MARVELL_PHY_ID_MASK },
{ MARVELL_PHY_ID_88E1548P, MARVELL_PHY_ID_MASK },
{ }
diff --git a/include/linux/marvell_phy.h b/include/linux/marvell_phy.h
index ff7b7607c8cf..f5cf19d19776 100644
--- a/include/linux/marvell_phy.h
+++ b/include/linux/marvell_phy.h
@@ -25,11 +25,12 @@
#define MARVELL_PHY_ID_88X3310 0x002b09a0
#define MARVELL_PHY_ID_88E2110 0x002b09b0
-/* The MV88e6390 Ethernet switch contains embedded PHYs. These PHYs do
+/* These Ethernet switch families contain embedded PHYs, but they do
* not have a model ID. So the switch driver traps reads to the ID2
* register and returns the switch family ID
*/
-#define MARVELL_PHY_ID_88E6390 0x01410f90
+#define MARVELL_PHY_ID_88E6341_FAMILY 0x01410f41
+#define MARVELL_PHY_ID_88E6390_FAMILY 0x01410f90
#define MARVELL_PHY_FAMILY_ID(id) ((id) >> 4)
--
2.20.1
