Hi
Op 17-04-2021 om 16:22 schreef Ferry Toth:
Hi
Op 17-04-2021 om 04:27 schreef Thinh Nguyen:
Ferry Toth wrote:
Hi
Op 16-04-2021 om 00:23 schreef Thinh Nguyen:
Thinh Nguyen wrote:
From: Yu Chen <chenyu56@xxxxxxxxxx>
From: John Stultz <john.stultz@xxxxxxxxxx>
According to the programming guide, to switch mode for DRD
controller,
the driver needs to do the following.
To switch from device to host:
1. Reset controller with GCTL.CoreSoftReset
2. Set GCTL.PrtCapDir(host mode)
3. Reset the host with USBCMD.HCRESET
4. Then follow up with the initializing host registers sequence
To switch from host to device:
1. Reset controller with GCTL.CoreSoftReset
2. Set GCTL.PrtCapDir(device mode)
3. Reset the device with DCTL.CSftRst
4. Then follow up with the initializing registers sequence
Currently we're missing step 1) to do GCTL.CoreSoftReset and step
3) of
switching from host to device. John Stult reported a lockup issue
seen
with HiKey960 platform without these steps[1]. Similar issue is
observed
with Ferry's testing platform[2].
So, apply the required steps along with some fixes to Yu Chen's
and John
Stultz's version. The main fixes to their versions are the missing
wait
for clocks synchronization before clearing GCTL.CoreSoftReset and
only
apply DCTL.CSftRst when switching from host to device.
[1]
https://urldefense.com/v3/__https://lore.kernel.org/linux-usb/20210108015115.27920-1-john.stultz@xxxxxxxxxx/__;!!A4F2R9G_pg!PW9Jbs4wv4a_zKGgZHN0FYrIpfecPX0Ouq9V3d16Yz-9-GSHqZWsfBAF-WkeqLhzN4i3$
[2]
https://urldefense.com/v3/__https://lore.kernel.org/linux-usb/0ba7a6ba-e6a7-9cd4-0695-64fc927e01f1@xxxxxxxxx/__;!!A4F2R9G_pg!PW9Jbs4wv4a_zKGgZHN0FYrIpfecPX0Ouq9V3d16Yz-9-GSHqZWsfBAF-WkeqGeZStt4$
Cc: Andy Shevchenko <andy.shevchenko@xxxxxxxxx>
Cc: Ferry Toth <fntoth@xxxxxxxxx>
Cc: Wesley Cheng <wcheng@xxxxxxxxxxxxxx>
Cc: <stable@xxxxxxxxxxxxxxx>
Fixes: 41ce1456e1db ("usb: dwc3: core: make dwc3_set_mode() work
properly")
Signed-off-by: Yu Chen <chenyu56@xxxxxxxxxx>
Signed-off-by: John Stultz <john.stultz@xxxxxxxxxx>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@xxxxxxxxxxxx>
---
Changes in v3:
- Check if the desired mode is OTG, then keep the old flow
- Remove condition for OTG support only since the device can still be
configured DRD host/device mode only
- Remove redundant hw_mode check since __dwc3_set_mode() only applies
when
hw_mode is DRD
Changes in v2:
- Initialize mutex per device and not as global mutex.
- Add additional checks for DRD only mode
drivers/usb/dwc3/core.c | 27 +++++++++++++++++++++++++++
drivers/usb/dwc3/core.h | 5 +++++
2 files changed, 32 insertions(+)
Hi John,
If possible, can you run a test with this version on your platform?
Thanks,
Thinh
I tested this on edison-arduino with this patch on top of usb-next
(5.12-rc7 + "increase BESL baseline to 6" to prevent throttling").
On this platform there is a physical switch to switch roles. With this
patch I find:
- switch to host mode always works fine
- switch to gadget mode I need to flip the switch 3x
(gadget-host-gadget).
An error message appears on the gadget side "dwc3 dwc3.0.auto: timed
out
waiting for SETUP phase" appears, but then the device connects to my
PC,
no throttling.
- alternatively I can switch to gadget 1x and then unplug/replug the
cable.
No error message and connects fine.
- if I flip the switch only once, on the PC side I get:
kernel: usb 1-5: new high-speed USB device number 18 using xhci_hcd
kernel: usb 1-5: New USB device found, idVendor=1d6b,
idProduct=0104, bcdDevice= 1.00 kernel: usb 1-5: New USB device
strings: Mfr=1, Product=2, SerialNumber=3 kernel: usb 1-5: Product:
USBArmory Gadget kernel: usb 1-5: Manufacturer: USBArmory kernel:
usb 1-5: SerialNumber: 0123456789abcdef kernel: usb 1-5: can't set
config #1, error -110
The device failed at set_configuration() request and timed out. It
probably timed out from the status stage looking at the device err
print.
Then if I wait long enough on the gadget side I get:
root@yuna:~# ifconfig
usb0: flags=-28605<UP,BROADCAST,RUNNING,MULTICAST,DYNAMIC> mtu 1500
inet 169.254.119.239 netmask 255.255.0.0 broadcast 169.254.255.255
inet6 fe80::a8bb:ccff:fedd:eef1 prefixlen 64 scopeid 0x20<link>
ether aa:bb:cc:dd:ee:f1 txqueuelen 1000 (Ethernet) RX packets 490424
bytes 735146578 (701.0 MiB) RX errors 0 dropped 191 overruns 0 frame
0 TX packets 35279 bytes 2532746 (2.4 MiB) TX errors 0 dropped 0
overruns 0 carrier 0 collisions 0
(correct would be: inet 10.42.0.221 netmask 255.255.255.0 broadcast
10.42.0.255)
So much improved now, but it seems I am still missing something on
plug.
That's great! We can look at it further. Can you capture the tracepoints
of the issue. Also, can you try with mass_storage gadget to see if the
result is the same?
I have already gser, eem, mass_storage and uac2 combo. When eem fails,
the mass_storage and uac2 don't appear (on KDE you get all kind of
popups when they appear).
So either all works, or all fails.
I'll trace this later today.
Trace capturing switch from host-> gadget here
https://github.com/andy-shev/linux/files/6329600/5.12-rc7%2Busb-next.zip
(Issue history: https://github.com/andy-shev/linux/issues/31)
On the PC side this resulted to:
apr 17 18:17:44 delfion kernel: usb 1-5: new high-speed USB device
number 12 using xhci_hcd
apr 17 18:17:44 delfion kernel: usb 1-5: New USB device found,
idVendor=1d6b, idProduct=0104, bcdDevice= 1.00
apr 17 18:17:44 delfion kernel: usb 1-5: New USB device strings: Mfr=1,
Product=2, SerialNumber=3
apr 17 18:17:44 delfion kernel: usb 1-5: Product: USBArmory Gadget
apr 17 18:17:44 delfion kernel: usb 1-5: Manufacturer: USBArmory
apr 17 18:17:44 delfion kernel: usb 1-5: SerialNumber: 0123456789abcdef
apr 17 18:17:49 delfion kernel: usb 1-5: can't set config #1, error -110
Thanks for all your help!
Thanks,
Thinh
