From: Zhen Lei <thunder.leizhen@xxxxxxxxxx> [ Upstream commit 2013a4b684b6eb614ee5c9a3c07b0ae6f5ca96d9 ] The scripts/dtc/checks.c requires that the node have empty "dma-ranges" property must have the same "#address-cells" and "#size-cells" values as the parent node. Otherwise, the following warnings is reported: arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ its #address-cells (1) differs from / (2) arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \ (dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \ its #size-cells (1) differs from / (2) Arnd Bergmann figured out why it's necessary: Also note that the #address-cells=<1> means that any device under this bus is assumed to only support 32-bit addressing, and DMA will have to go through a slow swiotlb in the absence of an IOMMU. Suggested-by: Arnd Bergmann <arnd@xxxxxxxx> Signed-off-by: Zhen Lei <thunder.leizhen@xxxxxxxxxx> Link: https://lore.kernel.org/r/20201016090833.1892-2-thunder.leizhen@xxxxxxxxxx' Acked-by: Florian Fainelli <f.fainelli@xxxxxxxxx> Signed-off-by: Arnd Bergmann <arnd@xxxxxxxx> Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx> --- .../dts/broadcom/stingray/stingray-usb.dtsi | 20 +++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi index 55259f973b5a9..aef8f2b00778d 100644 --- a/arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi +++ b/arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi @@ -5,20 +5,20 @@ usb { compatible = "simple-bus"; dma-ranges; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x0 0x0 0x68500000 0x00400000>; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0x0 0x0 0x0 0x68500000 0x0 0x00400000>; usbphy0: usb-phy@0 { compatible = "brcm,sr-usb-combo-phy"; - reg = <0x00000000 0x100>; + reg = <0x0 0x00000000 0x0 0x100>; #phy-cells = <1>; status = "disabled"; }; xhci0: usb@1000 { compatible = "generic-xhci"; - reg = <0x00001000 0x1000>; + reg = <0x0 0x00001000 0x0 0x1000>; interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>; phys = <&usbphy0 1>, <&usbphy0 0>; phy-names = "phy0", "phy1"; @@ -28,7 +28,7 @@ bdc0: usb@2000 { compatible = "brcm,bdc-v0.16"; - reg = <0x00002000 0x1000>; + reg = <0x0 0x00002000 0x0 0x1000>; interrupts = <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH>; phys = <&usbphy0 0>, <&usbphy0 1>; phy-names = "phy0", "phy1"; @@ -38,21 +38,21 @@ usbphy1: usb-phy@10000 { compatible = "brcm,sr-usb-combo-phy"; - reg = <0x00010000 0x100>; + reg = <0x0 0x00010000 0x0 0x100>; #phy-cells = <1>; status = "disabled"; }; usbphy2: usb-phy@20000 { compatible = "brcm,sr-usb-hs-phy"; - reg = <0x00020000 0x100>; + reg = <0x0 0x00020000 0x0 0x100>; #phy-cells = <0>; status = "disabled"; }; xhci1: usb@11000 { compatible = "generic-xhci"; - reg = <0x00011000 0x1000>; + reg = <0x0 0x00011000 0x0 0x1000>; interrupts = <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>; phys = <&usbphy1 1>, <&usbphy2>, <&usbphy1 0>; phy-names = "phy0", "phy1", "phy2"; @@ -62,7 +62,7 @@ bdc1: usb@21000 { compatible = "brcm,bdc-v0.16"; - reg = <0x00021000 0x1000>; + reg = <0x0 0x00021000 0x0 0x1000>; interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>; phys = <&usbphy2>; phy-names = "phy0"; -- 2.27.0
