Re: [PATCH] MIPS: Ingenic: Disable HPTLB for D0 XBurst CPUs too

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Paul,

On 2020/12/14 上午3:57, Paul Cercueil wrote:
Hi Zhou,

Le lun. 14 déc. 2020 à 3:12, Zhou Yanjie <zhouyanjie@xxxxxxxxxxxxxx> a écrit :
Hi Paul,

On 2020/12/12 上午8:03, Paul Cercueil wrote:
The JZ4760 has the HPTLB as well, but has a XBurst CPU with a D0 CPUID.

Disable the HPTLB for all XBurst CPUs with a D0 CPUID. In the case where
there is no HPTLB (e.g. for older SoCs), this won't have any side
effect.

Fixes: b02efeb05699 ("MIPS: Ingenic: Disable abandoned HPTLB function.")
Cc: <stable@xxxxxxxxxxxxxxx> # 5.4
Signed-off-by: Paul Cercueil <paul@xxxxxxxxxxxxxxx>
---
  arch/mips/kernel/cpu-probe.c | 15 ++++++++-------
  1 file changed, 8 insertions(+), 7 deletions(-)

diff --git a/arch/mips/kernel/cpu-probe.c b/arch/mips/kernel/cpu-probe.c
index e6853697a056..31cb9199197c 100644
--- a/arch/mips/kernel/cpu-probe.c
+++ b/arch/mips/kernel/cpu-probe.c
@@ -1830,16 +1830,17 @@ static inline void cpu_probe_ingenic(struct cpuinfo_mips *c, unsigned int cpu)
           */
          case PRID_COMP_INGENIC_D0:
              c->isa_level &= ~MIPS_CPU_ISA_M32R2;
-            break;
+            fallthrough;
            /*
           * The config0 register in the XBurst CPUs with a processor ID of -         * PRID_COMP_INGENIC_D1 has an abandoned huge page tlb mode, this -         * mode is not compatible with the MIPS standard, it will cause -         * tlbmiss and into an infinite loop (line 21 in the tlb-funcs.S) -         * when starting the init process. After chip reset, the default
-         * is HPTLB mode, Write 0xa9000000 to cp0 register 5 sel 4 to


I just noticed that I mistakenly wrote a capital 'W' in the original version.

with that fixed:

Reviewed-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@xxxxxxxxxxxxxx>

Sure, thanks.

If both D0 and D1 CPUs need the fix then I probably should move it outside the switch, that would make the code a bit cleaner. I'll V2.


This is a good idea, but it should be noted that it still needs to be placed in XBURST_REV1, because XBURST_REV2 processors (such as X1830) also use the ID of D0, but they do not have the problem of HPTLB.


BTW: Are you planning to add support for JZ4760 recently? I am currently writing the CGU driver for JZ4775 and X2000. If you plan to add support for JZ4760, I can also write the CGU driver for JZ4760 by the way.

Yes, we're working on it, all the core drivers are working (CGU, pinctrl, timers, display, USB), it boots to userspace and allows to telnet. The actual diff is very small, most of the changes were the addition of the ingenic,jz4760-* compatible strings.


Good to hear that.

Thanks and best regards!


Cheers,
-Paul

-         * switch back to VTLB mode to prevent getting stuck.
+         * PRID_COMP_INGENIC_D0 or PRID_COMP_INGENIC_D1 has an abandoned +         * huge page tlb mode, this mode is not compatible with the MIPS
+         * standard, it will cause tlbmiss and into an infinite loop
+         * (line 21 in the tlb-funcs.S) when starting the init process. +         * After chip reset, the default is HPTLB mode, Write 0xa9000000 +         * to cp0 register 5 sel 4 to switch back to VTLB mode to prevent
+         * getting stuck.
           */
          case PRID_COMP_INGENIC_D1:
              write_c0_page_ctrl(XBURST_PAGECTRL_HPTLB_DIS);




[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux