Re: [PATCH] staging: comedi: cb_pcidas: reinstate delay removed from trimpot setting

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 02/11/2020 11:16, Ian Abbott wrote:
On 02/11/2020 10:25, Ian Abbott wrote:
On 29/10/2020 14:18, Ian Abbott wrote:
Commit eddd2a4c675c ("staging: comedi: cb_pcidas: refactor
write_calibration_bitstream()") inadvertently removed one of the
`udelay(1)` calls when writing to the calibration register in
`cb_pcidas_calib_write()`.  Reinstate the delay.  It may seem strange
that the delay is placed before the register write, but this function is
called in a loop so the extra delay can make a difference.

This _might_ solve reported issues reading analog inputs on a
PCIe-DAS1602/16 card where the analog input values "were scaled in a
strange way that didn't make sense".  On the same hardware running a
system with a 3.13 kernel, and then a system with a 4.4 kernel, but with
the same application software, the system with the 3.13 kernel was fine,
but the one with the 4.4 kernel exhibited the problem.  Of the 90
changes to the driver between those kernel versions, this change looked
like the most likely culprit.

Actually, I've realized that this patch will have no effect on the PCIe-DAS1602/16 card because it uses a different driver - cb_pcimdas, not cb_pcidas.

But that's also confusing because PCIe-DAS1602/16 was not supported until the 3.19 kernel!  I know the reported has both PCI-DAS1602/16 and PCIe-DAS1602/16 cards (supported by cb_pcidas and cb_pcimdas respectively), so there could have been some mix-up in the reporting.

Mystery solved. The reporter had a mixture of PCIe-DAS1602/16 and PCIM-DAS1602/16 cards (not PCI-DAS1602/16). Both of those are supported by the "cb_pcimdas" driver (not "cb_pcidas"), although the PCIe card was not supported until the 3.19 kernel (by commit 4e3d14af1286). Testing with the 3.13 kernel was done with the PCIM card.

The "strange scaling" was due to a change in the ranges reported for the analog input subdevice in the 4.1 kernel (by commit c7549d770a27). Before then, it just reported a single dummy range [0, 1000000] with no units (converted to [0.0, 1.0] with no units by comedilib). Afterwards, it reported four different voltage ranges (either unipolar or bipolar, depending in a status bit tied to a physical switch). The reporter's application code was using the reported range to scale the raw values to a voltage (using comedilib functions), but because the reported range was bogus, the application code was performing additional scaling (outside of comedilib). The application code can be changed to check whether the device is reporting a proper voltage range or the old, bogus range, and behave accordingly.

Greg, you might as well drop this patch if you haven't already applied it, since it was only a hunch that it fixed a problem.

That's still the case, although it won't do any harm if applied (apart from the incorrect patch description).

--
-=( Ian Abbott <abbotti@xxxxxxxxx> || MEV Ltd. is a company  )=-
-=( registered in England & Wales.  Regd. number: 02862268.  )=-
-=( Regd. addr.: S11 & 12 Building 67, Europa Business Park, )=-
-=( Bird Hall Lane, STOCKPORT, SK3 0XA, UK. || www.mev.co.uk )=-



[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux