On Sat, May 23, 2020 at 05:09:50PM +0800, Chen Yu wrote: > Hi Michal, > Thanks for reviewing, > and sorry for late reply. > On Thu, May 21, 2020 at 09:23:42PM +0200, Michal Kubecek wrote: > > On Fri, May 22, 2020 at 01:59:13AM +0800, Chen Yu wrote: > > > Currently the ethtool shows that WOL(Wake On Lan) is enabled > > > even if the device wakeup ability has been disabled via sysfs: > > > cat /sys/devices/pci0000:00/0000:00:1f.6/power/wakeup > > > disabled > > > > > > ethtool eno1 > > > ... > > > Wake-on: g > > > > > > Fix this in ethtool to check if the user has explicitly disabled the > > > wake up ability for this device. > > > > Wouldn't this lead to rather unexpected and inconsistent behaviour when > > the wakeup is disabled? As you don't touch the set_wol handler, I assume > > it will still allow setting enabled modes as usual so that you get e.g. > > > > ethtool -s eth0 wol g # no error or warning, returns 0 > > ethtool eth0 # reports no modes enabled > > > > The first command would set the enabled wol modes but that would be > > hidden from user and even the netlink notification would claim something > > different. Another exampe (with kernel and ethtool >= 5.6): > > > > ethtool -s eth0 wol g > > ethtool -s eth0 wol +m > > > > resulting in "mg" if device wakeup is enabled but "m" when it's disabled > > (but the latter would be hidden from user and only revealed when you > > enable the device wakeup). > > > I've tested ethtool v5.6 on top of kernel v5.7-rc6, it looks like > the scenario you described will not happen as it will not allow > the user to enable the wol options with device wakeup disabled, > not sure if I missed something: > > /sys/devices/pci0000:00/0000:00:1f.6/power# echo disabled > wakeup > > ethtool -s eno1 wol g > netlink error: cannot enable unsupported WoL mode (offset 36) > netlink error: Invalid argument > > I've not digged into the code too much, but according to > ethhl_set_wol(), it will first get the current wol options > via dev->ethtool_ops->get_wol(), and both the wolopts and > wol.supported are 0 when device wake up are disabled. Then > ethnl_update_bitset32 might manipulate on wolopts and > make it non-zero each is controdict with the precondition that > no opts should be enabled due to 0 wol.supported. You are right, I didn't realize that you report 0 even for supported WoL modes. However, this feels even more wrong from my point of view as then even the list of supported WoL modes would be hidden from user when the sysfs switch is off. Also, AFAICS "ethtool -s <dev> wol d" would be still allowed but the behaviour would differ between ioctl and netlink code path: netlink would identify the operation as no-op and do nothing. But ioctl does not check new value against old one so that it would call your set_wol() handler which would set the (hidden) set of enabled WoL modes to empty which would mean WoL would stay disabled even after enabling the wakeup via sysctl. In other words, you would allow disabling all WoL modes (via ioctl) but not setting them to anything else. > > This is a general problem discussed recently for EEE and pause > > autonegotiation: if setting A can be effectively used only when B is > > enabled, should we hide actual setting of A from userspace when B is > > disabled or even reset the value of A whenever B gets toggled or rather > > allow setting A and B independently? AFAICS the consensus seemed to be > > that A should be allowed to be set and queried independently of the > > value of B. > > But then there would be an inconsistence between A and B. I was > thinking if there's a way to align them in kernel space and maintain > the difference in user space? I'm not sure what exactly you mean by maintaining the difference in userspace but there are many situations like this and we usually do not block the ability to query or set A when the "main switch" is off. For example, you can add IPv4/6 addresses to an interface when it is down, even if you cannot receive or transmit packets with these addresses. Or you can set up netlilter rules in FORWARDING chain independently of the global ip_forward sysctl which can block all IPv4 forwarding. Moreover, if we really wanted to report no supported and enabled WoL modes when device wakeup is disabled, it should be done for all network devices, not only in one driver. Michal
