The patch below does not apply to the 4.14-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable@xxxxxxxxxxxxxxx>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From e825070f697abddf3b9b0a675ed0ff1884114818 Mon Sep 17 00:00:00 2001
From: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
Date: Tue, 17 Dec 2019 19:10:38 +0200
Subject: [PATCH] iio: st_gyro: Correct data for LSM9DS0 gyro
The commit 41c128cb25ce ("iio: st_gyro: Add lsm9ds0-gyro support")
assumes that gyro in LSM9DS0 is the same as others with 0xd4 WAI ID,
but datasheet tells slight different story, i.e. the first scale factor
for the chip is 245 dps, and not 250 dps.
Correct this by introducing a separate settings for LSM9DS0.
Fixes: 41c128cb25ce ("iio: st_gyro: Add lsm9ds0-gyro support")
Depends-on: 45a4e4220bf4 ("iio: gyro: st_gyro: fix L3GD20H support")
Cc: Leonard Crestez <leonard.crestez@xxxxxxx>
Cc: Lorenzo Bianconi <lorenzo.bianconi83@xxxxxxxxx>
Cc: <Stable@xxxxxxxxxxxxxxx>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>
diff --git a/drivers/iio/gyro/st_gyro_core.c b/drivers/iio/gyro/st_gyro_core.c
index 57be68b291fa..26c50b24bc08 100644
--- a/drivers/iio/gyro/st_gyro_core.c
+++ b/drivers/iio/gyro/st_gyro_core.c
@@ -138,7 +138,6 @@ static const struct st_sensor_settings st_gyro_sensors_settings[] = {
[2] = LSM330DLC_GYRO_DEV_NAME,
[3] = L3G4IS_GYRO_DEV_NAME,
[4] = LSM330_GYRO_DEV_NAME,
- [5] = LSM9DS0_GYRO_DEV_NAME,
},
.ch = (struct iio_chan_spec *)st_gyro_16bit_channels,
.odr = {
@@ -208,6 +207,80 @@ static const struct st_sensor_settings st_gyro_sensors_settings[] = {
.multi_read_bit = true,
.bootime = 2,
},
+ {
+ .wai = 0xd4,
+ .wai_addr = ST_SENSORS_DEFAULT_WAI_ADDRESS,
+ .sensors_supported = {
+ [0] = LSM9DS0_GYRO_DEV_NAME,
+ },
+ .ch = (struct iio_chan_spec *)st_gyro_16bit_channels,
+ .odr = {
+ .addr = 0x20,
+ .mask = GENMASK(7, 6),
+ .odr_avl = {
+ { .hz = 95, .value = 0x00, },
+ { .hz = 190, .value = 0x01, },
+ { .hz = 380, .value = 0x02, },
+ { .hz = 760, .value = 0x03, },
+ },
+ },
+ .pw = {
+ .addr = 0x20,
+ .mask = BIT(3),
+ .value_on = ST_SENSORS_DEFAULT_POWER_ON_VALUE,
+ .value_off = ST_SENSORS_DEFAULT_POWER_OFF_VALUE,
+ },
+ .enable_axis = {
+ .addr = ST_SENSORS_DEFAULT_AXIS_ADDR,
+ .mask = ST_SENSORS_DEFAULT_AXIS_MASK,
+ },
+ .fs = {
+ .addr = 0x23,
+ .mask = GENMASK(5, 4),
+ .fs_avl = {
+ [0] = {
+ .num = ST_GYRO_FS_AVL_245DPS,
+ .value = 0x00,
+ .gain = IIO_DEGREE_TO_RAD(8750),
+ },
+ [1] = {
+ .num = ST_GYRO_FS_AVL_500DPS,
+ .value = 0x01,
+ .gain = IIO_DEGREE_TO_RAD(17500),
+ },
+ [2] = {
+ .num = ST_GYRO_FS_AVL_2000DPS,
+ .value = 0x02,
+ .gain = IIO_DEGREE_TO_RAD(70000),
+ },
+ },
+ },
+ .bdu = {
+ .addr = 0x23,
+ .mask = BIT(7),
+ },
+ .drdy_irq = {
+ .int2 = {
+ .addr = 0x22,
+ .mask = BIT(3),
+ },
+ /*
+ * The sensor has IHL (active low) and open
+ * drain settings, but only for INT1 and not
+ * for the DRDY line on INT2.
+ */
+ .stat_drdy = {
+ .addr = ST_SENSORS_DEFAULT_STAT_ADDR,
+ .mask = GENMASK(2, 0),
+ },
+ },
+ .sim = {
+ .addr = 0x23,
+ .value = BIT(0),
+ },
+ .multi_read_bit = true,
+ .bootime = 2,
+ },
{
.wai = 0xd7,
.wai_addr = ST_SENSORS_DEFAULT_WAI_ADDRESS,
