From: Vinod Koul <vkoul@xxxxxxxxxx>
[ Upstream commit a968b5e9d5879f9535d6099505f9e14abcafb623 ]
RGMII_ID specifies that we should have internal delay, so resurrect the
delay addition routine but under the RGMII_ID mode.
Fixes: 40269aa9f40a ("net: dsa: qca8k: disable delay for RGMII mode")
Tested-by: Michal Vokáč <michal.vokac@xxxxxxxxx>
Signed-off-by: Vinod Koul <vkoul@xxxxxxxxxx>
Reviewed-by: Andrew Lunn <andrew@xxxxxxx>
Signed-off-by: David S. Miller <davem@xxxxxxxxxxxxx>
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
---
drivers/net/dsa/qca8k.c | 12 ++++++++++++
drivers/net/dsa/qca8k.h | 1 +
2 files changed, 13 insertions(+)
diff --git a/drivers/net/dsa/qca8k.c b/drivers/net/dsa/qca8k.c
index ebfbaf8597f40..3bbe85aae49bb 100644
--- a/drivers/net/dsa/qca8k.c
+++ b/drivers/net/dsa/qca8k.c
@@ -460,6 +460,18 @@ qca8k_set_pad_ctrl(struct qca8k_priv *priv, int port, int mode)
qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL,
QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
break;
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ /* RGMII_ID needs internal delay. This is enabled through
+ * PORT5_PAD_CTRL for all ports, rather than individual port
+ * registers
+ */
+ qca8k_write(priv, reg,
+ QCA8K_PORT_PAD_RGMII_EN |
+ QCA8K_PORT_PAD_RGMII_TX_DELAY(QCA8K_MAX_DELAY) |
+ QCA8K_PORT_PAD_RGMII_RX_DELAY(QCA8K_MAX_DELAY));
+ qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL,
+ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
+ break;
case PHY_INTERFACE_MODE_SGMII:
qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN);
break;
diff --git a/drivers/net/dsa/qca8k.h b/drivers/net/dsa/qca8k.h
index 9c22bc3210cdf..db95168ca111d 100644
--- a/drivers/net/dsa/qca8k.h
+++ b/drivers/net/dsa/qca8k.h
@@ -40,6 +40,7 @@
((0x8 + (x & 0x3)) << 22)
#define QCA8K_PORT_PAD_RGMII_RX_DELAY(x) \
((0x10 + (x & 0x3)) << 20)
+#define QCA8K_MAX_DELAY 3
#define QCA8K_PORT_PAD_RGMII_RX_DELAY_EN BIT(24)
#define QCA8K_PORT_PAD_SGMII_EN BIT(7)
#define QCA8K_REG_MODULE_EN 0x030
--
2.20.1
