On Thu, 2014-01-16 at 14:00 -0800, Andy Lutomirski wrote: > On 01/14/2014 09:37 PM, Len Brown wrote: > > From: Len Brown <len.brown@xxxxxxxxx> > > > > In Linux-3.9 we removed the mwait_idle() loop: > > 'x86 idle: remove mwait_idle() and "idle=mwait" cmdline param' > > (69fb3676df3329a7142803bb3502fa59dc0db2e3) > > > > The reasoning was that modern machines should be sufficiently > > happy during the boot process using the default_idle() HALT loop, > > until cpuidle loads and either acpi_idle or intel_idle > > invoke the newer MWAIT-with-hints idle loop. > > > > But two machines reported problems: > > 1. Certain Core2-era machines support MWAIT-C1 and HALT only. > > MWAIT-C1 is preferred for optimal power and performance. > > But if they support just C1, cpuidle never loads and > > so they use the boot-time default idle loop forever. > > > > 2. Some laptops will boot-hang if HALT is used, > > but will boot successfully if MWAIT is used. > > This appears to be a hidden assumption in BIOS SMI, > > that is presumably valid on the proprietary OS > > where the BIOS was validated. > > > > https://bugzilla.kernel.org/show_bug.cgi?id=60770 > > > > So here we effectively revert the patch above, restoring > > the mwait_idle() loop. However, we don't bother restoring > > the idle=mwait cmdline parameter, since it appears to add > > no value. > > > > Maintainer notes: > > For 3.9, simply revert 69fb3676df > > for 3.10, patch -F3 applies, fuzz needed due to __cpuinit use in context > > For 3.11, 3.12, 3.13, this patch applies cleanly > > > > Cc: Mike Galbraith <bitbucket@xxxxxxxxx> > > Cc: Ian Malone <ibmalone@xxxxxxxxx> > > Cc: Josh Boyer <jwboyer@xxxxxxxxxx> > > Cc: <stable@xxxxxxxxxxxxxxx> # 3.9, 3.10, 3.11, 3.12, 3.13 > > Signed-off-by: Len Brown <len.brown@xxxxxxxxx> > > --- > > arch/x86/kernel/process.c | 46 ++++++++++++++++++++++++++++++++++++++++++++++ > > 1 file changed, 46 insertions(+) > > > > diff --git a/arch/x86/kernel/process.c b/arch/x86/kernel/process.c > > index 3fb8d95..db471a8 100644 > > --- a/arch/x86/kernel/process.c > > +++ b/arch/x86/kernel/process.c > > @@ -398,6 +398,49 @@ static void amd_e400_idle(void) > > default_idle(); > > } > > > > +/* > > + * Intel Core2 and older machines prefer MWAIT over HALT for C1. > > + * We can't rely on cpuidle installing MWAIT, because it will not load > > + * on systems that support only C1 -- so the boot default must be MWAIT. > > + * > > + * Some AMD machines are the opposite, they depend on using HALT. > > + * > > + * So for default C1, which is used during boot until cpuidle loads, > > + * use MWAIT-C1 on Intel HW that has it, else use HALT. > > + */ > > +static int prefer_mwait_c1_over_halt(const struct cpuinfo_x86 *c) > > +{ > > + if (c->x86_vendor != X86_VENDOR_INTEL) > > + return 0; > > + > > + if (!cpu_has(c, X86_FEATURE_MWAIT)) > > + return 0; > > + > > + return 1; > > +} > > + > > +/* > > + * MONITOR/MWAIT with no hints, used for default default C1 state. > > + * This invokes MWAIT with interrutps enabled and no flags, > > + * which is backwards compatible with the original MWAIT implementation. > > + */ > > + > > +static void mwait_idle(void) > > +{ > > + if (!need_resched()) { > > + if (this_cpu_has(X86_FEATURE_CLFLUSH_MONITOR)) > > + clflush((void *)¤t_thread_info()->flags); > > + > > + __monitor((void *)¤t_thread_info()->flags, 0, 0); > > + smp_mb(); > > + if (!need_resched()) > > + __sti_mwait(0, 0); > > + else > > + local_irq_enable(); > > + } else > > + local_irq_enable(); > > +} > > Admittedly, there may be relatively few users left, but SMP users on > C1-only Core 2 machines can, in principle, benefit from the monitor ^hugely > functionality of mwait to avoid rescheduling IPIs. This stuff changed > recently so it now works with the cpuidle drivers (it used to be > terminally broken). Should something be twiddling TS_POLLING > differently so that HLT gets the IPIs but mwait doesn't? Urk, definitely. The IPI is the primary cause of the size large cross core scheduling performance regression for my aging, but lovely Q6600. taskset 0xc pipe-test 1 3.8.13 3.397977 usecs/loop -- avg 3.400336 588.2 KHz master+ 4.798547 usecs/loop -- avg 4.791692 417.4 KHz -Mike -- To unsubscribe from this list: send the line "unsubscribe stable" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html