On Thu, May 09, 2019 at 05:36:29PM +0000, Nadav Amit wrote:
> > On May 9, 2019, at 3:38 AM, Peter Zijlstra <peterz@xxxxxxxxxxxxx> wrote:
> > diff --git a/mm/mmu_gather.c b/mm/mmu_gather.c
> > index 99740e1dd273..fe768f8d612e 100644
> > --- a/mm/mmu_gather.c
> > +++ b/mm/mmu_gather.c
> > @@ -244,15 +244,20 @@ void tlb_finish_mmu(struct mmu_gather *tlb,
> > unsigned long start, unsigned long end)
> > {
> > /*
> > - * If there are parallel threads are doing PTE changes on same range
> > - * under non-exclusive lock(e.g., mmap_sem read-side) but defer TLB
> > - * flush by batching, a thread has stable TLB entry can fail to flush
> > - * the TLB by observing pte_none|!pte_dirty, for example so flush TLB
> > - * forcefully if we detect parallel PTE batching threads.
> > + * Sensible comment goes here..
> > */
> > - if (mm_tlb_flush_nested(tlb->mm)) {
> > - __tlb_reset_range(tlb);
> > - __tlb_adjust_range(tlb, start, end - start);
> > + if (mm_tlb_flush_nested(tlb->mm) && !tlb->full_mm) {
> > + /*
> > + * Since we're can't tell what we actually should have
> > + * flushed flush everything in the given range.
> > + */
> > + tlb->start = start;
> > + tlb->end = end;
> > + tlb->freed_tables = 1;
> > + tlb->cleared_ptes = 1;
> > + tlb->cleared_pmds = 1;
> > + tlb->cleared_puds = 1;
> > + tlb->cleared_p4ds = 1;
> > }
> >
> > tlb_flush_mmu(tlb);
>
> As a simple optimization, I think it is possible to hold multiple nesting
> counters in the mm, similar to tlb_flush_pending, for freed_tables,
> cleared_ptes, etc.
>
> The first time you set tlb->freed_tables, you also atomically increase
> mm->tlb_flush_freed_tables. Then, in tlb_flush_mmu(), you just use
> mm->tlb_flush_freed_tables instead of tlb->freed_tables.
That sounds fraught with races and expensive; I would much prefer to not
go there for this arguably rare case.
Consider such fun cases as where CPU-0 sees and clears a PTE, CPU-1
races and doesn't see that PTE. Therefore CPU-0 sets and counts
cleared_ptes. Then if CPU-1 flushes while CPU-0 is still in mmu_gather,
it will see cleared_ptes count increased and flush that granularity,
OTOH if CPU-1 flushes after CPU-0 completes, it will not and potentiall
miss an invalidate it should have had.
This whole concurrent mmu_gather stuff is horrible.
/me ponders more....
So I think the fundamental race here is this:
CPU-0 CPU-1
tlb_gather_mmu(.start=1, tlb_gather_mmu(.start=2,
.end=3); .end=4);
ptep_get_and_clear_full(2)
tlb_remove_tlb_entry(2);
__tlb_remove_page();
if (pte_present(2)) // nope
tlb_finish_mmu();
// continue without TLBI(2)
// whoopsie
tlb_finish_mmu();
tlb_flush() -> TLBI(2)
And we can fix that by having tlb_finish_mmu() sync up. Never let a
concurrent tlb_finish_mmu() complete until all concurrenct mmu_gathers
have completed.
This should not be too hard to make happen.
