On 12/07/2013 06:46 PM, Karl Dahlke wrote:
> This may have appeared in 3.9.11 with the changes to tty.
> Don't know; I just started running 3.12 from kernel.org.
> Perhaps nobody saw it before because nobody runs command line programs,
> we're all on desktops or x or whatever,
> and even those in the command line are still raw.
> bash is raw by default, but I run it cooked.
> You can supress its readline functions like this.
>
> set +o emacs
> set +o vi
> set +o histexpand
> set +o history
>
> That puts its tty back into cooked mode.
>
> Come up in run level 3, command line mode,
> and bring up two consoles with bash in cooked mode as above.
> Set a simple prompt like this.
>
> PS1='$ '
>
> Switch to console 2 via alt-f2.
> Hit return.
> The cursor should drop to a new line then give you the $ prompt.
> But it puts the $ prompt next too the old one, then drops down
> to a blank line.
> The $ prompt and the crlf are out of sequence.
> Hit return a few more times and it will straighten itself out.
> Then switch back to console 1 alt-f1
> Hit return and the same bug,
> $ $
>
> hit return a few more times to straighten it out.
> Switch back to console 2 and the same problem.
> For me it's repeatable.
>
> It's also very confusing when I'm running other command line programs with cooked tty.
> For unknown reasons the crlf can come out at the wrong time,
> breaking lines or leaving lines together.
> My editor can run either way, so I've switched it over to readline mode
> and I haven't noticed any problems this way, yet.
> But I would prefer the cooked mode.
>
> I looked through MAINTAINERS but couldn't find
> a clear maintainer for drivers/tty/tty*.c
> Please forward this to the appropriate people.
Thanks for the report, Karl.
Please test the patch below (requires
commit 39434abd942c8e4b9c14c06a03b3245beaf8467f,
'n_tty: Fix missing newline echo').
This should fix the 'newline output after the new prompt' problem.
Note however that the other output order you observe is correct:
you press enter, a newline is echoed to terminal which mixes
with program output, the program ends, and the cooked mode
shell outputs an extra prompt because it reads a newline (which
the program did not read).
Regards,
Peter Hurley
--- >% ---
From: Peter Hurley <peter@xxxxxxxxxxxxxxxxxx>
Subject: [PATCH] n_tty: Fix apparent order of echoed output
With block processing of echoed output, observed output order is still
required. Push completed echoes and echo commands prior to output.
Introduce echo_mark echo buffer index, which tracks completed echo
commands; ie., those submitted via commit_echoes but which may not
have been committed. Ensure that completed echoes are output prior
to subsequent terminal writes in process_echoes().
Fixes newline/prompt output order in cooked mode shell.
Cc: <stable@xxxxxxxxxxxxxxx> # 3.12.x : 39434ab n_tty: Fix missing newline echo
Reported-by: Karl Dahlke <eklhad@xxxxxxxxxxx>
Reported-by: Mikulas Patocka <mpatocka@xxxxxxxxxx>
Signed-off-by: Peter Hurley <peter@xxxxxxxxxxxxxxxxxx>
---
drivers/tty/n_tty.c | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/drivers/tty/n_tty.c b/drivers/tty/n_tty.c
index ab24fe1..e9304b6 100644
--- a/drivers/tty/n_tty.c
+++ b/drivers/tty/n_tty.c
@@ -94,6 +94,7 @@ struct n_tty_data {
size_t canon_head;
size_t echo_head;
size_t echo_commit;
+ size_t echo_mark;
DECLARE_BITMAP(char_map, 256);
/* private to n_tty_receive_overrun (single-threaded) */
@@ -339,6 +340,7 @@ static void reset_buffer_flags(struct n_tty_data *ldata)
{
ldata->read_head = ldata->canon_head = ldata->read_tail = 0;
ldata->echo_head = ldata->echo_tail = ldata->echo_commit = 0;
+ ldata->echo_mark = 0;
ldata->line_start = 0;
ldata->erasing = 0;
@@ -791,6 +793,7 @@ static void commit_echoes(struct tty_struct *tty)
size_t head;
head = ldata->echo_head;
+ ldata->echo_mark = head;
old = ldata->echo_commit - ldata->echo_tail;
/* Process committed echoes if the accumulated # of bytes
@@ -815,10 +818,11 @@ static void process_echoes(struct tty_struct *tty)
size_t echoed;
if ((!L_ECHO(tty) && !L_ECHONL(tty)) ||
- ldata->echo_commit == ldata->echo_tail)
+ ldata->echo_mark == ldata->echo_tail)
return;
mutex_lock(&ldata->output_lock);
+ ldata->echo_commit = ldata->echo_mark;
echoed = __process_echoes(tty);
mutex_unlock(&ldata->output_lock);
@@ -826,6 +830,7 @@ static void process_echoes(struct tty_struct *tty)
tty->ops->flush_chars(tty);
}
+/* NB: echo_mark and echo_head should be equivalent here */
static void flush_echoes(struct tty_struct *tty)
{
struct n_tty_data *ldata = tty->disc_data;
--
1.8.1.2
--
To unsubscribe from this list: send the line "unsubscribe stable" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html