Re: [PATCH 1/2] iio: adc: at91: fix acking DRDY irq on simple conversions

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 24.09.2018 23:27, Jonathan Cameron wrote:
On Mon, 24 Sep 2018 21:00:56 +0100
Jonathan Cameron <jic23@xxxxxxxxxx> wrote:

On Mon, 24 Sep 2018 09:19:43 +0300
Eugen Hristev <eugen.hristev@xxxxxxxxxxxxx> wrote:

On 22.09.2018 13:31, Jonathan Cameron wrote:
On Thu, 20 Sep 2018 15:40:37 +0300
Eugen Hristev <eugen.hristev@xxxxxxxxxxxxx> wrote:
When doing simple conversions, the driver did not acknowledge the DRDY irq.
If this irq is not acked, it will be left pending, and as soon as a trigger
is enabled, the irq handler will be called, it doesn't know why this irq
has occurred because no channel is pending, and then we will have irq loop
and board will hang.

Fixes 0e589d5fb ("ARM: AT91: IIO: Add AT91 ADC driver.")
Cc: Maxime Ripard <maxime.ripard@xxxxxxxxxxx>
Cc: <stable@xxxxxxxxxxxxxxx>
Signed-off-by: Eugen Hristev <eugen.hristev@xxxxxxxxxxxxx>
---
   drivers/iio/adc/at91_adc.c | 5 +++++
   1 file changed, 5 insertions(+)

diff --git a/drivers/iio/adc/at91_adc.c b/drivers/iio/adc/at91_adc.c
index 44b5168..e85f859 100644
--- a/drivers/iio/adc/at91_adc.c
+++ b/drivers/iio/adc/at91_adc.c
@@ -712,6 +712,11 @@ static int at91_adc_read_raw(struct iio_dev *idev,
   		at91_adc_writel(st, AT91_ADC_CHDR,
   				AT91_ADC_CH(chan->channel));
   		at91_adc_writel(st, AT91_ADC_IDR, BIT(chan->channel));
+		/*
+		 * we need to ack the DRDY irq, otherwise it will be
+		 * left pending and irq handler will be confused
+		 */
+		at91_adc_readl(st, AT91_ADC_LCDR);

I'm curious as to how things were working before.  Does this only occur
if we do a raw_read whilst the buffer is enabled?

No. The situation is that the read raw does not properly cleans itself
up after it's done.
The DRDY bit is cleared only when LCDR (last converted data ) is being read.
Even if we read the per channel conversion data, the LCDR still needs to
be read to clear this irq status.
The driver does not use the DRDY irq but this irq status is still being
set in the status register.

Hmm. That is somewhat nasty if it results in false interrupts when you
then enable them.

I'm talking rubbish here.  Please ignore!



I would have assumed when it's not enabled, the irq would be masked and
never generated in the first place...

It may be that what we actually need to do is to prevent read_raw accesses
when the buffer is enabled (like lots of other drivers do precisely to
avoid this sort of condition). The problem there comes if we have
existing applications doing this combination as we are then breaking
userspace. If that's the case we'll need to be a bit more clever.

Hammering down an irq state in a non irq handling path isn't a good
solution.

Ok, I will move the clearing of the DRDY (LCDR read) in the irq path
then, and send a v2.

If that can be done cleanly, let us go with that approach. If not
what you have here with the addition of a comments saying that the
interrupt status is not masked, merely the interrupt and as a result needs
clearing for when you later enabled the interrupt, is fine.

This definitely sounds like one of those bits of hardware that
you can write software to use safely but they certainly didn't make
it easy to do so!

For what it's worth a small explanation:

The status in the ISR (interrupt status) is updated regardless of whether the IRQ is enabled in the IER (interrupt enable) or not. Actually "enabling DRDY" makes the hardware start raising the interrupt line on DRDY event if it's the case. but DRDY bit is still being asserted in the ISR. It works like this because someone might want to write some simple driver without IRQ, just poll the ISR for the status.

One other thing, in my driver, at91-sama5d2_adc, I had the same issue, and I am reading the DRDY in the EOC part after waking up from the wait. This makes the IRQ handler shorter by a few hundred cycles : read LCDR in the userspace-called read_raw. Do you want me to have a patch at some point to move the LCDR read in the IRQ handler for at91-sama5d2_adc as well ?

Eugen


Jonathan


Jonathan
st->last_value = 0;
   		st->done = false;






[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux