Re: [PATCH v3 1/3] mtd: rawnand: denali_dt: add more clocks based on IP datasheet

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Jun 15, 2018 at 10:18:50AM +0900, Masahiro Yamada wrote:
> According to the Denali User's Guide, this IP needs three clocks:
> 
>  - clk: controller core clock
> 
>  - clk_x: bus interface clock
> 
>  - ecc_clk: clock at which ECC circuitry is run
> 
> Currently, denali_dt.c requires a single anonymous clock and its
> frequency.  However, the driver needs to get the frequency of "clk_x"
> not "clk".  This is confusing because people tend to assume the
> anonymous clock means the core clock.  In fact, I got a report of
> SOCFPGA breakage because the timing parameters are calculated based
> on a wrong frequency.
> 
> Instead of the cheesy implementation, the clocks in the real hardware
> should be represented in the driver and the DT-binding.
> 
> However, adding new clocks would break the existing platforms.  For the
> backward compatibility, the driver still accepts a single clock just as
> before.  If clk_x is missing, clk_x_rate is set to a hardcoded value.
> This is fine for existing DT of Socionext UniPhier, and also fixes the
> issue of Altera (Intel) SOCFPGA because both platforms use 200 MHz for
> the bus interface clock.
> 
> Fixes: 1bb88666775e ("mtd: nand: denali: handle timing parameters by setup_data_interface()")
> Cc: linux-stable <stable@xxxxxxxxxxxxxxx> #4.14+
> Reported-by: Richard Weinberger <richard@xxxxxx>
> Signed-off-by: Masahiro Yamada <yamada.masahiro@xxxxxxxxxxxxx>
> ---
> 
> Changes in v3:
>   - Change the patch order so that the bug-fix one comes the first
> 
> Changes in v2:
>   - Split patches into sensible chunks
> 
>  .../devicetree/bindings/mtd/denali-nand.txt        |  5 +++
>  drivers/mtd/nand/raw/denali_dt.c                   | 49 ++++++++++++++++++++--
>  2 files changed, 50 insertions(+), 4 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt b/Documentation/devicetree/bindings/mtd/denali-nand.txt
> index 0ee8edb..f33da87 100644
> --- a/Documentation/devicetree/bindings/mtd/denali-nand.txt
> +++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt
> @@ -8,6 +8,9 @@ Required properties:
>    - reg : should contain registers location and length for data and reg.
>    - reg-names: Should contain the reg names "nand_data" and "denali_reg"
>    - interrupts : The interrupt number.
> +  - clocks: should contain phandle of the controller core clock, the bus
> +    interface clock, and the ECC circuit clock.
> +  - clock-names: should contain "nand", "nand_x", "ecc"

The subject says "add more clocks", but it doesn't look like any clocks 
were supported before. Or documentation was missing?

Please split bindings to a separate patch.

Rob



[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux