On Mon, 2018-04-02 at 17:21 -0400, Lyude Paul wrote:
> While enabling/disabling DPMS before link training with MST hubs is
> perfectly valid; unfortunately disabling DPMS results in some devices
> disabling their AUX CH block as well. For SST this isn't as much of a
> problem, but for MST we need to be able to continue handling aux
> transactions even when none of the sinks are turned on since it's
> possible for us to have a single atomic commit which results in
> disabling each downstream sink, followed by subsequently re-enabling
> each sink.
>
> If we don't do this, we'll end up stalling any pending ESI interrupts
> from the sink for up to 1ms. Unfortunately, dropping ESIs during this
> timespan makes it so that link fallback retraining for MST (which I will
> be submitting to the ML shortly) fails due to the channel EQ failure
> interrupts potentially getting dropped. Additionally, when performing a
> modeset that brings the hub status's link status from bad -> good having
> ESIs disabled for that long causes us to miss the hub's response to us
> trying to start link training as well.
>
> Since any sink with MST is going to support DisplayPort 1.2 anyway, save
> us the hassle of trying to wait until the sink comes back up and just
> never shut the aux block down.
>
> Signed-off-by: Lyude Paul <lyude@xxxxxxxxxx>
> Cc: Laura Abbott <labbott@xxxxxxxxxx>
> Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@xxxxxxxxx>
> Cc: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
> Cc: stable@xxxxxxxxxxxxxxx
> Fixes: ad260ab32a4d9 ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.")
We've come a full circle on this one :)
1) Originally, we had disable_ddi() setting the branch power state to
D3.
2) Then "Use MST sideband message transactions for dpms control" removed
that as a bug fix for some devices. The sideband solution was chosen
over the D3_AUX_ON approach this patch takes.
3) Next, "Write to SET_POWER dpcd to enable MST hub" effectively took us
back to the original state due to a regression.
4) Now, we are calling (3) a regression and implementing D3_AUX_ON.
I guess, this combination should work for most devices. But, we should
test this on a few different MST hubs before going ahead.
-DK
> ---
> drivers/gpu/drm/i915/intel_dp.c | 6 ++++--
> 1 file changed, 4 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
> index 62f82c4298ac..0479c377981b 100644
> --- a/drivers/gpu/drm/i915/intel_dp.c
> +++ b/drivers/gpu/drm/i915/intel_dp.c
> @@ -2589,11 +2589,13 @@ void intel_dp_sink_dpms(struct intel_dp *intel_dp, int mode)
> return;
>
> if (mode != DRM_MODE_DPMS_ON) {
> + unsigned char data = intel_dp->is_mst ?
> + DP_SET_POWER_D3_AUX_ON : DP_SET_POWER_D3;
> +
> if (downstream_hpd_needs_d0(intel_dp))
> return;
>
> - ret = drm_dp_dpcd_writeb(&intel_dp->aux, DP_SET_POWER,
> - DP_SET_POWER_D3);
> + ret = drm_dp_dpcd_writeb(&intel_dp->aux, DP_SET_POWER, data);
> } else {
> struct intel_lspcon *lspcon = dp_to_lspcon(intel_dp);
>