This is a note to let you know that I've just added the patch titled
regulator: ti-abb: Fix bias voltage glitch in transition to bypass mode
to the 3.11-stable tree which can be found at:
http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary
The filename of the patch is:
regulator-ti-abb-fix-bias-voltage-glitch-in-transition-to-bypass-mode.patch
and it can be found in the queue-3.11 subdirectory.
If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@xxxxxxxxxxxxxxx> know about it.
>From bf00ca35cec8f0894dcfd90f88b03af1d5c7b86f Mon Sep 17 00:00:00 2001
From: Nishanth Menon <nm@xxxxxx>
Date: Fri, 27 Sep 2013 08:25:14 -0500
Subject: regulator: ti-abb: Fix bias voltage glitch in transition to bypass mode
From: Nishanth Menon <nm@xxxxxx>
commit bf00ca35cec8f0894dcfd90f88b03af1d5c7b86f upstream.
As documented in Application Note SWPA117 v2.1(NDA), LDO override has a
requirement that when switching from Bias active + override active
mode(FBB/RBB) to Bypass(nominal) mode, LDO reset must be performed
*after* LDO transitions to Bypass(nominal) mode.
The same rule in reverse applies when switching from a ABB bypass mode
to ABB enabled - LDO override *must* be performed prior to transition to
required ABB mode, if we do not do that, the same glitch takes place.
Currently while transitioning to ABB bypass, we reset the LDO overide
prior to the transition which causes a few milliseconds where ABB LDO
voltage could go all the way to 800mV(based on SoC process node),
during this period, the delta voltage between VDD rail and VBB rail
could cause the system to improperly function.
Signed-off-by: Nishanth Menon <nm@xxxxxx>
Signed-off-by: Mark Brown <broonie@xxxxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
drivers/regulator/ti-abb-regulator.c | 16 ++++++++++++++--
1 file changed, 14 insertions(+), 2 deletions(-)
--- a/drivers/regulator/ti-abb-regulator.c
+++ b/drivers/regulator/ti-abb-regulator.c
@@ -279,8 +279,12 @@ static int ti_abb_set_opp(struct regulat
ti_abb_rmw(regs->opp_sel_mask, info->opp_sel, regs->control_reg,
abb->base);
- /* program LDO VBB vset override if needed */
- if (abb->ldo_base)
+ /*
+ * program LDO VBB vset override if needed for !bypass mode
+ * XXX: Do not switch sequence - for !bypass, LDO override reset *must*
+ * be performed *before* switch to bias mode else VBB glitches.
+ */
+ if (abb->ldo_base && info->opp_sel != TI_ABB_NOMINAL_OPP)
ti_abb_program_ldovbb(dev, abb, info);
/* Initiate ABB ldo change */
@@ -295,6 +299,14 @@ static int ti_abb_set_opp(struct regulat
if (ret)
goto out;
+ /*
+ * Reset LDO VBB vset override bypass mode
+ * XXX: Do not switch sequence - for bypass, LDO override reset *must*
+ * be performed *after* switch to bypass else VBB glitches.
+ */
+ if (abb->ldo_base && info->opp_sel == TI_ABB_NOMINAL_OPP)
+ ti_abb_program_ldovbb(dev, abb, info);
+
out:
return ret;
}
Patches currently in stable-queue which might be from nm@xxxxxx are
queue-3.11/regulator-ti-abb-fix-bias-voltage-glitch-in-transition-to-bypass-mode.patch
--
To unsubscribe from this list: send the line "unsubscribe stable" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html