Patch "arm64: dts: renesas: ulcb: Remove renesas, no-ether-link property" has been added to the 4.14-stable tree

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



This is a note to let you know that I've just added the patch titled

    arm64: dts: renesas: ulcb: Remove renesas, no-ether-link property

to the 4.14-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     arm64-dts-renesas-ulcb-remove-renesas-no-ether-link-property.patch
and it can be found in the queue-4.14 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@xxxxxxxxxxxxxxx> know about it.


>From foo@baz Wed Feb 28 16:23:28 CET 2018
From: Bogdan Mirea <Bogdan-Stefan_Mirea@xxxxxxxxxx>
Date: Thu, 21 Dec 2017 17:18:59 +0200
Subject: arm64: dts: renesas: ulcb: Remove renesas, no-ether-link property

From: Bogdan Mirea <Bogdan-Stefan_Mirea@xxxxxxxxxx>


[ Upstream commit 7d2901f809c110bd9a261e879d59efe62e3bc758 ]

The present change is a bug fix for AVB link iteratively up/down.

Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
  without user interaction,
- this may heal after some seconds or even stay for minutes.

As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.

Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
  the RX & TX are enabled/disabled directly from adjust_link function
  without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
  HW interrogation. The HW check is made through the LMON pin in PSR
  register which specifies AVB_LINK signal value (0 - at low level;
  1 - at high level).

In conclusion, the present change is also a safety improvement because
it removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.

Fixes: dc36965a8905 ("arm64: dts: r8a7796: salvator-x: Enable EthernetAVB")
Fixes: 6fa501c549aa ("arm64: dts: r8a7795: enable EthernetAVB on Salvator-X")
Signed-off-by: Bogdan Mirea <Bogdan-Stefan_Mirea@xxxxxxxxxx>
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@xxxxxxxxxx>
Signed-off-by: Simon Horman <horms+renesas@xxxxxxxxxxxx>
Signed-off-by: Sasha Levin <alexander.levin@xxxxxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
 arch/arm64/boot/dts/renesas/ulcb.dtsi |    1 -
 1 file changed, 1 deletion(-)

--- a/arch/arm64/boot/dts/renesas/ulcb.dtsi
+++ b/arch/arm64/boot/dts/renesas/ulcb.dtsi
@@ -145,7 +145,6 @@
 &avb {
 	pinctrl-0 = <&avb_pins>;
 	pinctrl-names = "default";
-	renesas,no-ether-link;
 	phy-handle = <&phy0>;
 	status = "okay";
 


Patches currently in stable-queue which might be from Bogdan-Stefan_Mirea@xxxxxxxxxx are

queue-4.14/arm64-dts-renesas-ulcb-remove-renesas-no-ether-link-property.patch



[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]