[PATCH for-4.14.y 4/5] e1000e: Avoid receiver overrun interrupt bursts

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Benjamin Poirier <bpoirier@xxxxxxxx>

commit 4aea7a5c5e940c1723add439f4088844cd26196d upstream.

When e1000e_poll() is not fast enough to keep up with incoming traffic, the
adapter (when operating in msix mode) raises the Other interrupt to signal
Receiver Overrun.

This is a double problem because 1) at the moment e1000_msix_other()
assumes that it is only called in case of Link Status Change and 2) if the
condition persists, the interrupt is repeatedly raised again in quick
succession.

Ideally we would configure the Other interrupt to not be raised in case of
receiver overrun but this doesn't seem possible on this adapter. Instead,
we handle the first part of the problem by reverting to the practice of
reading ICR in the other interrupt handler, like before commit 16ecba59bc33
("e1000e: Do not read ICR in Other interrupt"). Thanks to commit
0a8047ac68e5 ("e1000e: Fix msi-x interrupt automask") which cleared IAME
from CTRL_EXT, reading ICR doesn't interfere with RxQ0, TxQ0 interrupts
anymore. We handle the second part of the problem by not re-enabling the
Other interrupt right away when there is overrun. Instead, we wait until
traffic subsides, napi polling mode is exited and interrupts are
re-enabled.

Reported-by: Lennart Sorensen <lsorense@xxxxxxxxxxxxxxxxxxx>
Fixes: 16ecba59bc33 ("e1000e: Do not read ICR in Other interrupt")
Signed-off-by: Benjamin Poirier <bpoirier@xxxxxxxx>
Tested-by: Aaron Brown <aaron.f.brown@xxxxxxxxx>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@xxxxxxxxx>
Signed-off-by: Amit Pundir <amit.pundir@xxxxxxxxxx>
---
 drivers/net/ethernet/intel/e1000e/defines.h |  1 +
 drivers/net/ethernet/intel/e1000e/netdev.c  | 33 ++++++++++++++++++++++-------
 2 files changed, 26 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 0641c0098738..afb7ebe20b24 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -398,6 +398,7 @@
 #define E1000_ICR_LSC           0x00000004 /* Link Status Change */
 #define E1000_ICR_RXSEQ         0x00000008 /* Rx sequence error */
 #define E1000_ICR_RXDMT0        0x00000010 /* Rx desc min. threshold (0) */
+#define E1000_ICR_RXO           0x00000040 /* Receiver Overrun */
 #define E1000_ICR_RXT0          0x00000080 /* Rx timer intr (ring 0) */
 #define E1000_ICR_ECCER         0x00400000 /* Uncorrectable ECC Error */
 /* If this bit asserted, the driver should claim the interrupt */
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 83071fe99323..99e5ef561f06 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -1910,14 +1910,30 @@ static irqreturn_t e1000_msix_other(int __always_unused irq, void *data)
 	struct net_device *netdev = data;
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	struct e1000_hw *hw = &adapter->hw;
+	u32 icr;
+	bool enable = true;
+
+	icr = er32(ICR);
+	if (icr & E1000_ICR_RXO) {
+		ew32(ICR, E1000_ICR_RXO);
+		enable = false;
+		/* napi poll will re-enable Other, make sure it runs */
+		if (napi_schedule_prep(&adapter->napi)) {
+			adapter->total_rx_bytes = 0;
+			adapter->total_rx_packets = 0;
+			__napi_schedule(&adapter->napi);
+		}
+	}
+	if (icr & E1000_ICR_LSC) {
+		ew32(ICR, E1000_ICR_LSC);
+		hw->mac.get_link_status = true;
+		/* guard against interrupt when we're going down */
+		if (!test_bit(__E1000_DOWN, &adapter->state))
+			mod_timer(&adapter->watchdog_timer, jiffies + 1);
+	}
 
-	hw->mac.get_link_status = true;
-
-	/* guard against interrupt when we're going down */
-	if (!test_bit(__E1000_DOWN, &adapter->state)) {
-		mod_timer(&adapter->watchdog_timer, jiffies + 1);
+	if (enable && !test_bit(__E1000_DOWN, &adapter->state))
 		ew32(IMS, E1000_IMS_OTHER);
-	}
 
 	return IRQ_HANDLED;
 }
@@ -2687,7 +2703,8 @@ static int e1000e_poll(struct napi_struct *napi, int weight)
 		napi_complete_done(napi, work_done);
 		if (!test_bit(__E1000_DOWN, &adapter->state)) {
 			if (adapter->msix_entries)
-				ew32(IMS, adapter->rx_ring->ims_val);
+				ew32(IMS, adapter->rx_ring->ims_val |
+				     E1000_IMS_OTHER);
 			else
 				e1000_irq_enable(adapter);
 		}
@@ -4204,7 +4221,7 @@ static void e1000e_trigger_lsc(struct e1000_adapter *adapter)
 	struct e1000_hw *hw = &adapter->hw;
 
 	if (adapter->msix_entries)
-		ew32(ICS, E1000_ICS_OTHER);
+		ew32(ICS, E1000_ICS_LSC | E1000_ICS_OTHER);
 	else
 		ew32(ICS, E1000_ICS_LSC);
 }
-- 
2.7.4




[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]