This is a note to let you know that I've just added the patch titled drm: adv7511: really enable interrupts for EDID detection to the 4.4-stable tree which can be found at: http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary The filename of the patch is: drm-adv7511-really-enable-interrupts-for-edid-detection.patch and it can be found in the queue-4.4 subdirectory. If you, or anyone else, feels it should not be added to the stable tree, please let <stable@xxxxxxxxxxxxxxx> know about it. >From d0be8584b01160eb6f49e77f8e9c1da286bb4ffb Mon Sep 17 00:00:00 2001 From: Wolfram Sang <wsa+renesas@xxxxxxxxxxxxxxxxxxxx> Date: Mon, 4 Jan 2016 03:33:45 +0100 Subject: drm: adv7511: really enable interrupts for EDID detection From: Wolfram Sang <wsa+renesas@xxxxxxxxxxxxxxxxxxxx> commit d0be8584b01160eb6f49e77f8e9c1da286bb4ffb upstream. The interrupts for EDID_READY or DDC_ERROR were never enabled in this driver, so reading EDID always timed out when chip was powered down and interrupts were used. Fix this and also remove clearing the interrupt flags, they are cleared in POWER_DOWN mode anyhow (unlike the interrupt enable flags) according to docs and my tests. Signed-off-by: Wolfram Sang <wsa+renesas@xxxxxxxxxxxxxxxxxxxx> Tested-by: Archit Taneja <architt@xxxxxxxxxxxxxx> Signed-off-by: Thong Ho <thong.ho.px@xxxxxxxxxxxxxxx> Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@xxxxxxxxxxx> Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx> --- drivers/gpu/drm/i2c/adv7511.c | 25 +++++++++++++++++-------- 1 file changed, 17 insertions(+), 8 deletions(-) --- a/drivers/gpu/drm/i2c/adv7511.c +++ b/drivers/gpu/drm/i2c/adv7511.c @@ -362,12 +362,19 @@ static void adv7511_power_on(struct adv7 { adv7511->current_edid_segment = -1; - regmap_write(adv7511->regmap, ADV7511_REG_INT(0), - ADV7511_INT0_EDID_READY); - regmap_write(adv7511->regmap, ADV7511_REG_INT(1), - ADV7511_INT1_DDC_ERROR); regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER, ADV7511_POWER_POWER_DOWN, 0); + if (adv7511->i2c_main->irq) { + /* + * Documentation says the INT_ENABLE registers are reset in + * POWER_DOWN mode. My 7511w preserved the bits, however. + * Still, let's be safe and stick to the documentation. + */ + regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(0), + ADV7511_INT0_EDID_READY); + regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(1), + ADV7511_INT1_DDC_ERROR); + } /* * Per spec it is allowed to pulse the HDP signal to indicate that the @@ -567,12 +574,14 @@ static int adv7511_get_modes(struct drm_ /* Reading the EDID only works if the device is powered */ if (!adv7511->powered) { - regmap_write(adv7511->regmap, ADV7511_REG_INT(0), - ADV7511_INT0_EDID_READY); - regmap_write(adv7511->regmap, ADV7511_REG_INT(1), - ADV7511_INT1_DDC_ERROR); regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER, ADV7511_POWER_POWER_DOWN, 0); + if (adv7511->i2c_main->irq) { + regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(0), + ADV7511_INT0_EDID_READY); + regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(1), + ADV7511_INT1_DDC_ERROR); + } adv7511->current_edid_segment = -1; } Patches currently in stable-queue which might be from wsa+renesas@xxxxxxxxxxxxxxxxxxxx are queue-4.4/drm-bridge-adv7511-use-work_struct-to-defer-hotplug-handing-to-out-of-irq-context.patch queue-4.4/drm-bridge-adv7511-re-write-the-i2c-address-before-edid-probing.patch queue-4.4/drm-adv7511-really-enable-interrupts-for-edid-detection.patch queue-4.4/drm-bridge-adv7511-switch-to-using-drm_kms_helper_hotplug_event.patch