Hi,
On Thursday 20 July 2017 08:19 PM, Sharma, Shashank wrote:
Acked-by: Shashank Sharma <shashank.sharma@xxxxxxxxx>
Regards
Shashank
On 7/20/2017 4:20 AM, Imre Deak wrote:
The scaler allocation code depends on a non-zero default value for the
crtc scaler_id, so make sure we initialize the scaler state accordingly
even if the crtc is off. This fixes at least an initial YUV420 modeset
(added in a follow-up patchset by Shashank) when booting with the screen
off: after the initial HW readout and modeset which enables the scaler a
subsequent modeset will disable the scaler which isn't properly
allocated. This results in a funky HW state where the pipe scaler HW
registers can't be modified and the normally black screen is grey and
shifted to the right or jitters.
The problem was revealed by Shashank's YUV420 patchset and first
reported by Ville.
Cc: Shashank Sharma <shashank.sharma@xxxxxxxxx>
Cc: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
Cc: Chandra Konduru <chandra.konduru@xxxxxxxxx>
Cc: Matt Roper <matthew.d.roper@xxxxxxxxx>
Cc: <stable@xxxxxxxxxxxxxxx> # 4.11.x
Reported-by: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
Fixes: a1b2278e4dfc ("drm/i915: skylake panel fitting using shared
scalers")
Signed-off-by: Imre Deak <imre.deak@xxxxxxxxx>
---
[ Older stable versions need backporting, so that's for a follow-up ]
---
drivers/gpu/drm/i915/intel_display.c | 14 +++++++-------
1 file changed, 7 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_display.c
b/drivers/gpu/drm/i915/intel_display.c
index 7774f3465fbc..8a38e64b1931 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -9132,6 +9132,13 @@ static bool haswell_get_pipe_config(struct
intel_crtc *crtc,
u64 power_domain_mask;
bool active;
+ if (INTEL_GEN(dev_priv) >= 9) {
+ intel_crtc_init_scalers(crtc, pipe_config);
+
+ pipe_config->scaler_state.scaler_id = -1;
+ pipe_config->scaler_state.scaler_users &= ~(1 <<
SKL_CRTC_INDEX);
We are already setting scaler_id to -1 during init_scalers & doing
memset over intel_crtc_state in intel_modeset_readout_hw_state, So IMO
above 2 lines are unnecessary..
Should not we reading actual HW state of scaler here instead of just
clearing it.
-Mahesh
+ }
+
power_domain = POWER_DOMAIN_PIPE(crtc->pipe);
if (!intel_display_power_get_if_enabled(dev_priv, power_domain))
return false;
@@ -9160,13 +9167,6 @@ static bool haswell_get_pipe_config(struct
intel_crtc *crtc,
pipe_config->gamma_mode =
I915_READ(GAMMA_MODE(crtc->pipe)) & GAMMA_MODE_MODE_MASK;
- if (INTEL_GEN(dev_priv) >= 9) {
- intel_crtc_init_scalers(crtc, pipe_config);
-
- pipe_config->scaler_state.scaler_id = -1;
- pipe_config->scaler_state.scaler_users &= ~(1 <<
SKL_CRTC_INDEX);
- }
-
power_domain = POWER_DOMAIN_PIPE_PANEL_FITTER(crtc->pipe);
if (intel_display_power_get_if_enabled(dev_priv, power_domain)) {
power_domain_mask |= BIT_ULL(power_domain);
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx