On Mon, Apr 17, 2017 at 01:56:54PM +0200, Marek Vasut wrote:
> This development kit has an FT4232 on it with a custom USB VID/PID.
> The FT4232 provides four UARTs, but only two are used. The UART 0
> is used by the FlashPro5 programmer and UART 2 is connected to the
> SmartFusion2 CortexM3 SoC UART port.
Thanks for verifying that you do not want to bind to interface 0.
Judging from the above description, it seems we can do even even better
and only bind to interface 2 using
USB_DEVICE_INTERFACE_NUMBER()
since you only have one uart connected that you want to expose, right?
> Note that the USB VID is registered to Actel according to Linux USB
> VID database, but that was acquired by Microsemi.
>
> Signed-off-by: Marek Vasut <marex@xxxxxxx>
> Cc: stable <stable@xxxxxxxxxxxxxxx>
> Cc: usb <linux-usb@xxxxxxxxxxxxxxx>
> Cc: Johan Hovold <johan@xxxxxxxxxx>
> ---
> V2: - Move the ID in ftdi_sio_ids.h to keep it sorted by VIDs
> - Use the JTAG quirk to avoid binding channel 0, this is needed by
> the Libero software, otherwise it cannot use the programmer.
> ---
> drivers/usb/serial/ftdi_sio.c | 2 ++
> drivers/usb/serial/ftdi_sio_ids.h | 10 ++++++++++
> 2 files changed, 12 insertions(+)
>
> diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
> index 80c6d3deb80d..a42e7f2af420 100644
> --- a/drivers/usb/serial/ftdi_sio.c
> +++ b/drivers/usb/serial/ftdi_sio.c
> @@ -873,6 +873,8 @@ static const struct usb_device_id id_table_combined[] = {
> { USB_DEVICE_AND_INTERFACE_INFO(MICROCHIP_VID, MICROCHIP_USB_BOARD_PID,
> USB_CLASS_VENDOR_SPEC,
> USB_SUBCLASS_VENDOR_SPEC, 0x00) },
> + { USB_DEVICE(ACTEL_VID, MICROSEMI_ARROW_SF2PLUS_BOARD_PID),
> + .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
> { USB_DEVICE(JETI_VID, JETI_SPC1201_PID) },
> { USB_DEVICE(MARVELL_VID, MARVELL_SHEEVAPLUG_PID),
> .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
> diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h
> index 168ccb03ce08..7b6edb8e9ee2 100644
> --- a/drivers/usb/serial/ftdi_sio_ids.h
> +++ b/drivers/usb/serial/ftdi_sio_ids.h
> @@ -877,6 +877,16 @@
> #define FIC_VID 0x1457
> #define FIC_NEO1973_DEBUG_PID 0x5118
>
> +/*
> + * Microsemi/Arrow SF2PLUS Dev Kit
> + *
> + * This board has an FT4232 on it which provides four UART ports.
> + * UART 0 is used by the FlashPro5 programmer, UART 2 is connected
> + * to the UART of an CortexM3 SoC-FPGA on the board.
You can remove this comment (having it in the git history should be
sufficient), and just make this a "Microsemi (formerly Actel)" header.
> + */
> +#define ACTEL_VID 0x1514
> +#define MICROSEMI_ARROW_SF2PLUS_BOARD_PID 0x2008
> +
> /* Olimex */
> #define OLIMEX_VID 0x15BA
> #define OLIMEX_ARM_USB_OCD_PID 0x0003
Thanks,
Johan