Re: [SCSI REGRESSION] 3.10.2 or 3.10.3: arcmsr failure at bootup / early userspace transition

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 07/31/2013 07:51 PM, Bernd Schubert wrote:
> On 07/31/2013 05:15 AM, Martin K. Petersen wrote:
>>>>>>> "Bernd" == Bernd Schubert <bernd.schubert@xxxxxxxxxxx> writes:
>>
>> Bernd,
>>
>>>> Product revision level: R001 
>>
>> It's clearly not verbatim passthrough...
>>
>> Bernd> Besides the firmware, the difference might be that I'm exporting
>> Bernd> single disks without any areca-raidset in between.  I can try to
>> Bernd> confirm that tomorrow, I just need the system as it is till
>> Bernd> tomorrow noon.
>>
>> That would be a great data point. I don't have any Areca boards.
>>
> 
> Just tested it, areca-raidset does not make a difference, but the
> firmware version does. After downgrading to 1.46 I have the same issue.
> 
> It is getting a bit late for me, but as this a pure development system,
> which is also booted over nfs, I can investigate it tomorrow.
> 


I couldn't resist and captured a few logs, see attachment. Is
0xffff88007feff180 the VPD inquiry? Can't we just cancel that command if
submitting it fails and then turn off VPD inquiry for this controller?
Jul 31 20:08:33 fslab1 kernel: [    0.000000] Linux version 3.11.0-rc1+ (schubert@fsdevel2) (gcc version 4.7.2 (Debian 4.7.2-5) ) #18 SMP Fri Jul 19 17:10:20 CEST 2013
Jul 31 20:08:33 fslab1 kernel: [    0.000000] Command line: crashkernel=256M console=tty0 console=ttyS0,115200 rw hpet=force
Jul 31 20:08:33 fslab1 kernel: [    0.000000] e820: BIOS-provided physical RAM map:
Jul 31 20:08:33 fslab1 kernel: [    0.000000] BIOS-e820: [mem 0x0000000000000100-0x000000000009fbff] usable
Jul 31 20:08:33 fslab1 kernel: [    0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
Jul 31 20:08:33 fslab1 kernel: [    0.000000] BIOS-e820: [mem 0x00000000000e6000-0x00000000000fffff] reserved
Jul 31 20:08:33 fslab1 kernel: [    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000cbfcffff] usable
Jul 31 20:08:33 fslab1 kernel: [    0.000000] BIOS-e820: [mem 0x00000000cbfd0000-0x00000000cbfddfff] ACPI data
Jul 31 20:08:33 fslab1 kernel: [    0.000000] BIOS-e820: [mem 0x00000000cbfde000-0x00000000cbffffff] ACPI NVS
Jul 31 20:08:33 fslab1 kernel: [    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
Jul 31 20:08:33 fslab1 kernel: [    0.000000] BIOS-e820: [mem 0x00000000ff780000-0x00000000ffffffff] reserved
Jul 31 20:08:33 fslab1 kernel: [    0.000000] BIOS-e820: [mem 0x0000000100000000-0x00000001ffffffff] usable
Jul 31 20:08:33 fslab1 kernel: [    0.000000] NX (Execute Disable) protection: active
Jul 31 20:08:33 fslab1 kernel: [    0.000000] SMBIOS 2.3 present.
Jul 31 20:08:33 fslab1 kernel: [    0.000000] No AGP bridge found
Jul 31 20:08:33 fslab1 kernel: [    0.000000] e820: last_pfn = 0x200000 max_arch_pfn = 0x400000000
Jul 31 20:08:33 fslab1 kernel: [    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Jul 31 20:08:33 fslab1 kernel: [    0.000000] e820: last_pfn = 0xcbfd0 max_arch_pfn = 0x400000000
Jul 31 20:08:33 fslab1 kernel: [    0.000000] found SMP MP-table at [mem 0x000ff780-0x000ff78f] mapped at [ffff8800000ff780]
Jul 31 20:08:33 fslab1 kernel: [    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
Jul 31 20:08:33 fslab1 kernel: [    0.000000] init_memory_mapping: [mem 0x1ffe00000-0x1ffffffff]
Jul 31 20:08:33 fslab1 kernel: [    0.000000] init_memory_mapping: [mem 0x1fc000000-0x1ffdfffff]
Jul 31 20:08:33 fslab1 kernel: [    0.000000] init_memory_mapping: [mem 0x180000000-0x1fbffffff]
Jul 31 20:08:33 fslab1 kernel: [    0.000000] init_memory_mapping: [mem 0x00100000-0xcbfcffff]
Jul 31 20:08:33 fslab1 kernel: [    0.000000] init_memory_mapping: [mem 0x100000000-0x17fffffff]
Jul 31 20:08:33 fslab1 kernel: [    0.000000] RAMDISK: [mem 0x7f3a0000-0x7fff4fff]
Jul 31 20:08:33 fslab1 kernel: [    0.000000] Reserving 256MB of memory at 640MB for crashkernel (System RAM: 7359MB)
Jul 31 20:08:33 fslab1 kernel: [    0.000000] ACPI: RSDP 00000000000f88a0 00014 (v00 ACPIAM)
Jul 31 20:08:33 fslab1 kernel: [    0.000000] ACPI: RSDT 00000000cbfd0000 00038 (v01 A M I  OEMRSDT  04000607 MSFT 00000097)
Jul 31 20:08:33 fslab1 kernel: [    0.000000] ACPI: FACP 00000000cbfd0200 00084 (v02 A M I  OEMFACP  04000607 MSFT 00000097)
Jul 31 20:08:33 fslab1 kernel: [    0.000000] ACPI: DSDT 00000000cbfd0410 057C8 (v01  1ACAI 1ACAI003 00000003 INTL 02002026)
Jul 31 20:08:33 fslab1 kernel: [    0.000000] ACPI: FACS 00000000cbfde000 00040
Jul 31 20:08:33 fslab1 kernel: [    0.000000] ACPI: APIC 00000000cbfd0390 00078 (v01 A M I  OEMAPIC  04000607 MSFT 00000097)
Jul 31 20:08:33 fslab1 kernel: [    0.000000] ACPI: OEMB 00000000cbfde040 00073 (v01 A M I  AMI_OEM  04000607 MSFT 00000097)
Jul 31 20:08:33 fslab1 kernel: [    0.000000] ACPI: SRAT 00000000cbfd5be0 00110 (v01 A M I  OEMSRAT  04000607 MSFT 00000097)
Jul 31 20:08:33 fslab1 kernel: [    0.000000] ACPI: MCFG 00000000cbfd5cf0 0003C (v01 A M I  OEMMCFG  04000607 MSFT 00000097)
Jul 31 20:08:33 fslab1 kernel: [    0.000000] SRAT: PXM 0 -> APIC 0x00 -> Node 0
Jul 31 20:08:33 fslab1 kernel: [    0.000000] SRAT: PXM 1 -> APIC 0x01 -> Node 1
Jul 31 20:08:33 fslab1 kernel: [    0.000000] SRAT: Node 0 PXM 0 [mem 0x00100000-0xcbffffff]
Jul 31 20:08:33 fslab1 kernel: [    0.000000] SRAT: Node 1 PXM 1 [mem 0x100000000-0x1ffffffff]
Jul 31 20:08:33 fslab1 kernel: [    0.000000] SRAT: Node 0 PXM 0 [mem 0x100000000-0xffffffff]
Jul 31 20:08:33 fslab1 kernel: [    0.000000] SRAT: Node 0 PXM 0 [mem 0x00000000-0x0009fbff]
Jul 31 20:08:33 fslab1 kernel: [    0.000000] NUMA: Node 0 [mem 0x00100000-0xcbffffff] + [mem 0x00000000-0x0009fbff] -> [mem 0x00000000-0xcbffffff]
Jul 31 20:08:33 fslab1 kernel: [    0.000000] Initmem setup node 0 [mem 0x00000000-0xcbffffff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000]   NODE_DATA [mem 0xcbfcb000-0xcbfcffff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Initmem setup node 1 [mem 0x100000000-0x1ffffffff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000]   NODE_DATA [mem 0x1ffff5000-0x1ffff9fff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Zone ranges:
Jul 31 20:08:34 fslab1 kernel: [    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000]   Normal   [mem 0x100000000-0x1ffffffff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Movable zone start for each node
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Early memory node ranges
Jul 31 20:08:34 fslab1 kernel: [    0.000000]   node   0: [mem 0x00001000-0x0009efff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000]   node   0: [mem 0x00100000-0xcbfcffff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000]   node   1: [mem 0x100000000-0x1ffffffff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Nvidia board detected. Ignoring ACPI timer override.
Jul 31 20:08:34 fslab1 kernel: [    0.000000] If you got timer trouble try acpi_use_timer_override
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Detected use of extended apic ids on hypertransport bus
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Detected use of extended apic ids on hypertransport bus
Jul 31 20:08:34 fslab1 kernel: [    0.000000] ACPI: PM-Timer IO Port: 0x4008
Jul 31 20:08:34 fslab1 kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Jul 31 20:08:34 fslab1 kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Jul 31 20:08:34 fslab1 kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
Jul 31 20:08:34 fslab1 kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
Jul 31 20:08:34 fslab1 kernel: [    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
Jul 31 20:08:34 fslab1 kernel: [    0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
Jul 31 20:08:34 fslab1 kernel: [    0.000000] ACPI: IOAPIC (id[0x03] address[0xdf6fc000] gsi_base[24])
Jul 31 20:08:34 fslab1 kernel: [    0.000000] IOAPIC[1]: apic_id 3, version 17, address 0xdf6fc000, GSI 24-47
Jul 31 20:08:34 fslab1 kernel: [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Jul 31 20:08:34 fslab1 kernel: [    0.000000] ACPI: BIOS IRQ0 override ignored.
Jul 31 20:08:34 fslab1 kernel: [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Using ACPI (MADT) for SMP configuration information
Jul 31 20:08:34 fslab1 kernel: [    0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
Jul 31 20:08:34 fslab1 kernel: [    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000e5fff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000] PM: Registered nosave memory: [mem 0x000e6000-0x000fffff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000] PM: Registered nosave memory: [mem 0xcbfd0000-0xcbfddfff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000] PM: Registered nosave memory: [mem 0xcbfde000-0xcbffffff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000] PM: Registered nosave memory: [mem 0xcc000000-0xfebfffff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xff77ffff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000] PM: Registered nosave memory: [mem 0xff780000-0xffffffff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000] e820: [mem 0xcc000000-0xfebfffff] available for PCI devices
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Booting paravirtualized kernel on bare hardware
Jul 31 20:08:34 fslab1 kernel: [    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:2
Jul 31 20:08:34 fslab1 kernel: [    0.000000] PERCPU: Embedded 28 pages/cpu @ffff8800cbc00000 s85824 r8192 d20672 u1048576
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Built 2 zonelists in Node order, mobility grouping on.  Total pages: 1858229
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Policy zone: Normal
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Kernel command line: crashkernel=256M console=tty0 console=ttyS0,115200 rw hpet=force
Jul 31 20:08:34 fslab1 kernel: [    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Checking aperture...
Jul 31 20:08:34 fslab1 kernel: [    0.000000] No AGP bridge found
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Node 0: aperture @ 8000000 size 64 MB
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Aperture pointing to e820 RAM. Ignoring.
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Your BIOS doesn't leave a aperture memory hole
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Please enable the IOMMU option in the BIOS setup
Jul 31 20:08:34 fslab1 kernel: [    0.000000] This costs you 64 MB of RAM
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Mapping aperture over 65536 KB of RAM @ c0000000
Jul 31 20:08:34 fslab1 kernel: [    0.000000] PM: Registered nosave memory: [mem 0xc0000000-0xc3ffffff]
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Memory: 7014524K/7536056K available (5420K kernel code, 877K rwdata, 1724K rodata, 988K init, 784K bss, 521532K reserved)
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Hierarchical RCU implementation.
Jul 31 20:08:34 fslab1 kernel: [    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
Jul 31 20:08:34 fslab1 kernel: [    0.000000] 	RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
Jul 31 20:08:34 fslab1 kernel: [    0.000000] NR_IRQS:33024 nr_irqs:1024 16
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Console: colour VGA+ 80x25
Jul 31 20:08:34 fslab1 kernel: [    0.000000] console [tty0] enabled
Jul 31 20:08:34 fslab1 kernel: [    0.000000] console [ttyS0] enabled
Jul 31 20:08:34 fslab1 kernel: [    0.000000] Enabling automatic NUMA balancing. Configure with numa_balancing= or sysctl
Jul 31 20:08:34 fslab1 kernel: [    0.000000] tsc: Fast TSC calibration using PIT
Jul 31 20:08:34 fslab1 kernel: [    0.000000] tsc: Detected 2399.870 MHz processor
Jul 31 20:08:34 fslab1 kernel: [    0.000000] tsc: Marking TSC unstable due to TSCs unsynchronized
Jul 31 20:08:34 fslab1 kernel: [    0.016000] Calibrating delay loop (skipped), value calculated using timer frequency.. 4799.74 BogoMIPS (lpj=9599480)
Jul 31 20:08:34 fslab1 kernel: [    0.020002] pid_max: default: 32768 minimum: 301
Jul 31 20:08:34 fslab1 kernel: [    0.024069] Security Framework initialized
Jul 31 20:08:34 fslab1 kernel: [    0.028011] TOMOYO Linux initialized
Jul 31 20:08:34 fslab1 kernel: [    0.032749] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Jul 31 20:08:34 fslab1 kernel: [    0.042558] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Jul 31 20:08:34 fslab1 kernel: [    0.048413] Mount-cache hash table entries: 256
Jul 31 20:08:34 fslab1 kernel: [    0.052285] Initializing cgroup subsys devices
Jul 31 20:08:34 fslab1 kernel: [    0.056005] Initializing cgroup subsys freezer
Jul 31 20:08:34 fslab1 kernel: [    0.060003] Initializing cgroup subsys net_cls
Jul 31 20:08:34 fslab1 kernel: [    0.064003] Initializing cgroup subsys blkio
Jul 31 20:08:34 fslab1 kernel: [    0.068040] mce: CPU supports 5 MCE banks
Jul 31 20:08:34 fslab1 kernel: [    0.072011] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 4
Jul 31 20:08:34 fslab1 kernel: [    0.072011] Last level dTLB entries: 4KB 512, 2MB 8, 4MB 4
Jul 31 20:08:34 fslab1 kernel: [    0.072011] tlb_flushall_shift: 4
Jul 31 20:08:34 fslab1 kernel: [    0.076080] Freeing SMP alternatives memory: 20K (ffffffff818d1000 - ffffffff818d6000)
Jul 31 20:08:34 fslab1 kernel: [    0.080869] ACPI: Core revision 20130517
Jul 31 20:08:34 fslab1 kernel: [    0.090913] ACPI: All ACPI Tables successfully acquired
Jul 31 20:08:34 fslab1 kernel: [    0.096847] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
Jul 31 20:08:34 fslab1 kernel: [    0.142648] smpboot: CPU0: AMD Opteron(tm) Processor 250 (fam: 0f, model: 25, stepping: 01)
Jul 31 20:08:34 fslab1 kernel: [    0.152000] Performance Events: AMD PMU driver.
Jul 31 20:08:34 fslab1 kernel: [    0.152003] ... version:                0
Jul 31 20:08:34 fslab1 kernel: [    0.156001] ... bit width:              48
Jul 31 20:08:34 fslab1 kernel: [    0.160001] ... generic registers:      4
Jul 31 20:08:34 fslab1 kernel: [    0.164001] ... value mask:             0000ffffffffffff
Jul 31 20:08:34 fslab1 kernel: [    0.168001] ... max period:             00007fffffffffff
Jul 31 20:08:34 fslab1 kernel: [    0.172001] ... fixed-purpose events:   0
Jul 31 20:08:34 fslab1 kernel: [    0.176001] ... event mask:             000000000000000f
Jul 31 20:08:34 fslab1 kernel: [    0.181636] smpboot: Booting Node   1, Processors  #1
Jul 31 20:08:34 fslab1 kernel: [    0.276085] Brought up 2 CPUs
Jul 31 20:08:34 fslab1 kernel: [    0.279349] smpboot: Total of 2 processors activated (9600.02 BogoMIPS)
Jul 31 20:08:34 fslab1 kernel: [    0.280640] devtmpfs: initialized
Jul 31 20:08:34 fslab1 kernel: [    0.289066] PM: Registering ACPI NVS region [mem 0xcbfde000-0xcbffffff] (139264 bytes)
Jul 31 20:08:34 fslab1 kernel: [    0.293555] regulator-dummy: no parameters
Jul 31 20:08:34 fslab1 kernel: [    0.296095] NET: Registered protocol family 16
Jul 31 20:08:34 fslab1 kernel: [    0.300154] TOM: 00000000cc000000 aka 3264M
Jul 31 20:08:34 fslab1 kernel: [    0.304023] TOM2: 0000000200000000 aka 8192M
Jul 31 20:08:34 fslab1 kernel: [    0.308057] ACPI: bus type PCI registered
Jul 31 20:08:34 fslab1 kernel: [    0.312081] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
Jul 31 20:08:34 fslab1 kernel: [    0.316003] PCI: not using MMCONFIG
Jul 31 20:08:34 fslab1 kernel: [    0.320001] PCI: Using configuration type 1 for base access
Jul 31 20:08:34 fslab1 kernel: [    0.328152] bio: create slab <bio-0> at 0
Jul 31 20:08:34 fslab1 kernel: [    0.332071] ACPI: Added _OSI(Module Device)
Jul 31 20:08:34 fslab1 kernel: [    0.336003] ACPI: Added _OSI(Processor Device)
Jul 31 20:08:34 fslab1 kernel: [    0.340002] ACPI: Added _OSI(3.0 _SCP Extensions)
Jul 31 20:08:34 fslab1 kernel: [    0.344002] ACPI: Added _OSI(Processor Aggregator Device)
Jul 31 20:08:34 fslab1 kernel: [    0.355183] ACPI: Executed 1 blocks of module-level executable AML code
Jul 31 20:08:34 fslab1 kernel: [    0.366682] ACPI: Interpreter enabled
Jul 31 20:08:34 fslab1 kernel: [    0.368013] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130517/hwxface-571)
Jul 31 20:08:34 fslab1 kernel: [    0.378260] ACPI: (supports S0 S1 S3 S4 S5)
Jul 31 20:08:34 fslab1 kernel: [    0.380002] ACPI: Using IOAPIC for interrupt routing
Jul 31 20:08:34 fslab1 kernel: [    0.384036] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
Jul 31 20:08:34 fslab1 kernel: [    0.393168] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
Jul 31 20:08:34 fslab1 kernel: [    0.409180] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
Jul 31 20:08:34 fslab1 kernel: [    0.412192] ACPI: No dock devices found.
Jul 31 20:08:34 fslab1 kernel: [    0.433752] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-03])
Jul 31 20:08:34 fslab1 kernel: [    0.440537] PCI host bridge to bus 0000:00
Jul 31 20:08:34 fslab1 kernel: [    0.444004] pci_bus 0000:00: root bus resource [bus 00-03]
Jul 31 20:08:34 fslab1 kernel: [    0.448002] pci_bus 0000:00: root bus resource [io  0x6000-0xcfff]
Jul 31 20:08:34 fslab1 kernel: [    0.452002] pci_bus 0000:00: root bus resource [io  0x0000-0x4fff]
Jul 31 20:08:34 fslab1 kernel: [    0.456002] pci_bus 0000:00: root bus resource [mem 0xcc000000-0xdf4fffff]
Jul 31 20:08:34 fslab1 kernel: [    0.460002] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
Jul 31 20:08:34 fslab1 kernel: [    0.464002] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
Jul 31 20:08:34 fslab1 kernel: [    0.468002] pci_bus 0000:00: root bus resource [mem 0xec000000-0xffffffff]
Jul 31 20:08:34 fslab1 kernel: [    0.472002] pci_bus 0000:00: root bus resource [mem 0x200000000-0xfcffffffff]
Jul 31 20:08:34 fslab1 kernel: [    0.476421] pci 0000:00:02.0: System wakeup disabled by ACPI
Jul 31 20:08:34 fslab1 kernel: [    0.480126] pci 0000:00:02.1: System wakeup disabled by ACPI
Jul 31 20:08:34 fslab1 kernel: [    0.484587] pci 0000:00:09.0: System wakeup disabled by ACPI
Jul 31 20:08:34 fslab1 kernel: [    0.488125] pci 0000:00:0a.0: System wakeup disabled by ACPI
Jul 31 20:08:34 fslab1 kernel: [    0.492140] pci 0000:00:0d.0: System wakeup disabled by ACPI
Jul 31 20:08:34 fslab1 kernel: [    0.496138] pci 0000:00:0e.0: System wakeup disabled by ACPI
Jul 31 20:08:34 fslab1 kernel: [    0.501134] pci 0000:00:09.0: PCI bridge to [bus 03] (subtractive decode)
Jul 31 20:08:34 fslab1 kernel: [    0.504073] pci 0000:00:0d.0: PCI bridge to [bus 02]
Jul 31 20:08:34 fslab1 kernel: [    0.508456] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
Jul 31 20:08:34 fslab1 kernel: [    0.512007] pci 0000:00:0e.0: PCI bridge to [bus 01]
Jul 31 20:08:34 fslab1 kernel: [    0.516018] acpi PNP0A03:00: ACPI _OSC support notification failed, disabling PCIe ASPM
Jul 31 20:08:34 fslab1 kernel: [    0.520002] acpi PNP0A03:00: Unable to request _OSC control (_OSC support mask: 0x08)
Jul 31 20:08:34 fslab1 kernel: [    0.528158] ACPI: PCI Root Bridge [PCIB] (domain 0000 [bus 80-84])
Jul 31 20:08:34 fslab1 kernel: [    0.532537] PCI host bridge to bus 0000:80
Jul 31 20:08:34 fslab1 kernel: [    0.536008] pci_bus 0000:80: root bus resource [bus 80-84]
Jul 31 20:08:34 fslab1 kernel: [    0.540002] pci_bus 0000:80: root bus resource [io  0xd000-0xffff]
Jul 31 20:08:34 fslab1 kernel: [    0.544002] pci_bus 0000:80: root bus resource [io  0x5000-0x5fff]
Jul 31 20:08:34 fslab1 kernel: [    0.548002] pci_bus 0000:80: root bus resource [mem 0xdf500000-0xdfffffff]
Jul 31 20:08:34 fslab1 kernel: [    0.552002] pci_bus 0000:80: root bus resource [mem 0xe8000000-0xebffffff]
Jul 31 20:08:34 fslab1 kernel: [    0.556498] pci 0000:80:0a.0: System wakeup disabled by ACPI
Jul 31 20:08:34 fslab1 kernel: [    0.560117] pci 0000:80:0d.0: System wakeup disabled by ACPI
Jul 31 20:08:34 fslab1 kernel: [    0.564118] pci 0000:80:0e.0: System wakeup disabled by ACPI
Jul 31 20:08:34 fslab1 kernel: [    0.568100] pci 0000:80:0d.0: PCI bridge to [bus 84]
Jul 31 20:08:34 fslab1 kernel: [    0.580011] pci 0000:80:0e.0: PCI bridge to [bus 81-83]
Jul 31 20:08:34 fslab1 kernel: [    0.584230] pci 0000:81:00.0: PCI bridge to [bus 83]
Jul 31 20:08:34 fslab1 kernel: [    0.588083] pci 0000:81:00.2: PCI bridge to [bus 82]
Jul 31 20:08:34 fslab1 kernel: [    0.592017] acpi PNP0A03:01: ACPI _OSC support notification failed, disabling PCIe ASPM
Jul 31 20:08:34 fslab1 kernel: [    0.596002] acpi PNP0A03:01: Unable to request _OSC control (_OSC support mask: 0x08)
Jul 31 20:08:34 fslab1 kernel: [    0.600264] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
Jul 31 20:08:34 fslab1 kernel: [    0.607035] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
Jul 31 20:08:34 fslab1 kernel: [    0.611042] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 *18 19)
Jul 31 20:08:34 fslab1 kernel: [    0.617516] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 *19)
Jul 31 20:08:34 fslab1 kernel: [    0.621820] ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *0, disabled.
Jul 31 20:08:34 fslab1 kernel: [    0.627031] ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *0, disabled.
Jul 31 20:08:34 fslab1 kernel: [    0.630729] ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *0, disabled.
Jul 31 20:08:34 fslab1 kernel: [    0.637814] ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *0, disabled.
Jul 31 20:08:34 fslab1 kernel: [    0.645379] ACPI: PCI Interrupt Link [LKLN] (IRQs 20 21 22) *0, disabled.
Jul 31 20:08:34 fslab1 kernel: [    0.652381] ACPI: PCI Interrupt Link [LAUI] (IRQs 20 21 22) *0, disabled.
Jul 31 20:08:34 fslab1 kernel: [    0.658729] ACPI: PCI Interrupt Link [LKMO] (IRQs 20 21 22) *0, disabled.
Jul 31 20:08:34 fslab1 kernel: [    0.662728] ACPI: PCI Interrupt Link [LKSM] (IRQs 20 21 22) *0, disabled.
Jul 31 20:08:34 fslab1 kernel: [    0.670428] ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 *22)
Jul 31 20:08:34 fslab1 kernel: [    0.676526] ACPI: PCI Interrupt Link [LTIE] (IRQs 20 *21 22)
Jul 31 20:08:34 fslab1 kernel: [    0.681546] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22) *0, disabled.
Jul 31 20:08:34 fslab1 kernel: [    0.689833] ACPI: PCI Interrupt Link [LN2A] (IRQs 40 41 42 *43)
Jul 31 20:08:34 fslab1 kernel: [    0.696386] ACPI: PCI Interrupt Link [LN2B] (IRQs 40 41 42 43) *0, disabled.
Jul 31 20:08:34 fslab1 kernel: [    0.704046] ACPI: PCI Interrupt Link [LN2C] (IRQs 40 41 42 43) *0, disabled.
Jul 31 20:08:34 fslab1 kernel: [    0.711035] ACPI: PCI Interrupt Link [LN2D] (IRQs 40 41 42 43) *0, disabled.
Jul 31 20:08:34 fslab1 kernel: [    0.715036] ACPI: PCI Interrupt Link [LK2N] (IRQs 44 45 46 47) *0, disabled.
Jul 31 20:08:34 fslab1 kernel: [    0.722734] ACPI: PCI Interrupt Link [LT3D] (IRQs 44 45 46 *47)
Jul 31 20:08:34 fslab1 kernel: [    0.729222] ACPI: PCI Interrupt Link [LT2E] (IRQs 44 45 *46 47)
Jul 31 20:08:34 fslab1 kernel: [    0.734021] vgaarb: device added: PCI:0000:03:01.0,decodes=io+mem,owns=none,locks=none
Jul 31 20:08:34 fslab1 kernel: [    0.740009] vgaarb: loaded
Jul 31 20:08:34 fslab1 kernel: [    0.744001] vgaarb: bridge control possible 0000:03:01.0
Jul 31 20:08:34 fslab1 kernel: [    0.752056] ACPI: bus type USB registered
Jul 31 20:08:34 fslab1 kernel: [    0.756035] usbcore: registered new interface driver usbfs
Jul 31 20:08:34 fslab1 kernel: [    0.760017] usbcore: registered new interface driver hub
Jul 31 20:08:34 fslab1 kernel: [    0.764015] usbcore: registered new device driver usb
Jul 31 20:08:34 fslab1 kernel: [    0.772091] PCI: Using ACPI for IRQ routing
Jul 31 20:08:34 fslab1 kernel: [    0.782618] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Jul 31 20:08:34 fslab1 kernel: [    0.788006] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
Jul 31 20:08:34 fslab1 kernel: [    0.793156] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
Jul 31 20:08:34 fslab1 kernel: [    0.802018] Switched to clocksource hpet
Jul 31 20:08:34 fslab1 kernel: [    0.814071] pnp: PnP ACPI init
Jul 31 20:08:34 fslab1 kernel: [    0.817232] ACPI: bus type PNP registered
Jul 31 20:08:34 fslab1 kernel: [    0.824057] pnp 00:08: disabling [mem 0xdfefc000-0xdfefcfff] because it overlaps 0000:80:0e.0 BAR 15 [mem 0xdf700000-0xdfefffff 64bit pref]
Jul 31 20:08:34 fslab1 kernel: [    0.836670] pnp 00:08: disabling [mem 0xdfefd000-0xdfefd3ff] because it overlaps 0000:80:0e.0 BAR 15 [mem 0xdf700000-0xdfefffff 64bit pref]
Jul 31 20:08:34 fslab1 kernel: [    0.849289] pnp 00:08: disabling [mem 0xdfefe000-0xdfefe3ff] because it overlaps 0000:80:0e.0 BAR 15 [mem 0xdf700000-0xdfefffff 64bit pref]
Jul 31 20:08:34 fslab1 kernel: [    0.861907] pnp 00:08: disabling [mem 0xdfeff000-0xdfefffff] because it overlaps 0000:80:0e.0 BAR 15 [mem 0xdf700000-0xdfefffff 64bit pref]
Jul 31 20:08:34 fslab1 kernel: [    0.874527] pnp 00:08: disabling [mem 0xdfefc000-0xdfefcfff disabled] because it overlaps 0000:81:00.0 BAR 15 [mem 0xdf700000-0xdfefffff 64bit pref]
Jul 31 20:08:34 fslab1 kernel: [    0.887928] pnp 00:08: disabling [mem 0xdfefd000-0xdfefd3ff disabled] because it overlaps 0000:81:00.0 BAR 15 [mem 0xdf700000-0xdfefffff 64bit pref]
Jul 31 20:08:34 fslab1 kernel: [    0.901325] pnp 00:08: disabling [mem 0xdfefe000-0xdfefe3ff disabled] because it overlaps 0000:81:00.0 BAR 15 [mem 0xdf700000-0xdfefffff 64bit pref]
Jul 31 20:08:34 fslab1 kernel: [    0.914723] pnp 00:08: disabling [mem 0xdfeff000-0xdfefffff disabled] because it overlaps 0000:81:00.0 BAR 15 [mem 0xdf700000-0xdfefffff 64bit pref]
Jul 31 20:08:34 fslab1 kernel: [    0.928158] system 00:08: [io  0x0190-0x0193] has been reserved
Jul 31 20:08:34 fslab1 kernel: [    0.934144] system 00:08: [io  0x04d0-0x04d1] has been reserved
Jul 31 20:08:34 fslab1 kernel: [    0.940134] system 00:08: [io  0x4000-0x40ff window] could not be reserved
Jul 31 20:08:34 fslab1 kernel: [    0.947076] system 00:08: [io  0x4400-0x44ff window] has been reserved
Jul 31 20:08:34 fslab1 kernel: [    0.953672] system 00:08: [io  0x4800-0x48ff window] has been reserved
Jul 31 20:08:34 fslab1 kernel: [    0.960269] system 00:08: [mem 0xffb80000-0xfffffffe] has been reserved
Jul 31 20:08:34 fslab1 kernel: [    0.966948] system 00:08: [mem 0xfefff000-0xfeffffff] has been reserved
Jul 31 20:08:34 fslab1 kernel: [    0.973769] system 00:09: [mem 0xfec00000-0xfec00fff] could not be reserved
Jul 31 20:08:34 fslab1 kernel: [    0.980802] system 00:09: [mem 0xfee00000-0xfeefffff] has been reserved
Jul 31 20:08:34 fslab1 kernel: [    0.988019] system 00:0a: [io  0x0680-0x06ff] has been reserved
Jul 31 20:08:34 fslab1 kernel: [    0.994005] system 00:0a: [io  0x0295-0x0296] has been reserved
Jul 31 20:08:34 fslab1 kernel: [    0.999992] system 00:0a: [io  0x0778-0x077f] has been reserved
Jul 31 20:08:34 fslab1 kernel: [    1.005981] system 00:0a: [io  0x0b78-0x0b7f] has been reserved
Jul 31 20:08:34 fslab1 kernel: [    1.011970] system 00:0a: [io  0x0f78-0x0f7f] has been reserved
Jul 31 20:08:34 fslab1 kernel: [    1.018080] system 00:0b: [mem 0xe0000000-0xefffffff] could not be reserved
Jul 31 20:08:34 fslab1 kernel: [    1.025421] system 00:0c: [mem 0x00000000-0x0009ffff] could not be reserved
Jul 31 20:08:34 fslab1 kernel: [    1.032454] system 00:0c: [mem 0x000c0000-0x000dffff] could not be reserved
Jul 31 20:08:34 fslab1 kernel: [    1.039482] system 00:0c: [mem 0x000e0000-0x000fffff] could not be reserved
Jul 31 20:08:34 fslab1 kernel: [    1.046511] system 00:0c: [mem 0x00100000-0xcbffffff] could not be reserved
Jul 31 20:08:34 fslab1 kernel: [    1.054233] pnp: PnP ACPI: found 13 devices
Jul 31 20:08:34 fslab1 kernel: [    1.058478] ACPI: bus type PNP unregistered
Jul 31 20:08:34 fslab1 kernel: [    1.069953] pci 0000:00:09.0: PCI bridge to [bus 03]
Jul 31 20:08:34 fslab1 kernel: [    1.074982] pci 0000:00:09.0:   bridge window [io  0x8000-0x8fff]
Jul 31 20:08:34 fslab1 kernel: [    1.081139] pci 0000:00:09.0:   bridge window [mem 0xcc200000-0xce2fffff]
Jul 31 20:08:34 fslab1 kernel: [    1.087995] pci 0000:00:09.0:   bridge window [mem 0xcf400000-0xdf3fffff pref]
Jul 31 20:08:34 fslab1 kernel: [    1.095310] pci 0000:00:0d.0: PCI bridge to [bus 02]
Jul 31 20:08:34 fslab1 kernel: [    1.100342] pci 0000:00:0e.0: PCI bridge to [bus 01]
Jul 31 20:08:34 fslab1 kernel: [    1.105366] pci 0000:00:0e.0:   bridge window [mem 0xcc000000-0xcc1fffff]
Jul 31 20:08:34 fslab1 kernel: [    1.112218] pci 0000:00:0e.0:   bridge window [mem 0xce400000-0xcf3fffff 64bit pref]
Jul 31 20:08:34 fslab1 kernel: [    1.120057] pci 0000:80:0d.0: PCI bridge to [bus 84]
Jul 31 20:08:34 fslab1 kernel: [    1.125087] pci 0000:81:00.0: PCI bridge to [bus 83]
Jul 31 20:08:34 fslab1 kernel: [    1.130119] pci 0000:81:00.0:   bridge window [mem 0xdf500000-0xdf5fffff]
Jul 31 20:08:34 fslab1 kernel: [    1.136971] pci 0000:81:00.0:   bridge window [mem 0xdf700000-0xdfefffff 64bit pref]
Jul 31 20:08:34 fslab1 kernel: [    1.144806] pci 0000:81:00.2: PCI bridge to [bus 82]
Jul 31 20:08:34 fslab1 kernel: [    1.149840] pci 0000:80:0e.0: PCI bridge to [bus 81-83]
Jul 31 20:08:34 fslab1 kernel: [    1.155131] pci 0000:80:0e.0:   bridge window [mem 0xdf500000-0xdf5fffff]
Jul 31 20:08:34 fslab1 kernel: [    1.161983] pci 0000:80:0e.0:   bridge window [mem 0xdf700000-0xdfefffff 64bit pref]
Jul 31 20:08:34 fslab1 kernel: [    1.169981] NET: Registered protocol family 2
Jul 31 20:08:34 fslab1 kernel: [    1.174716] TCP established hash table entries: 65536 (order: 8, 1048576 bytes)
Jul 31 20:08:34 fslab1 kernel: [    1.182724] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
Jul 31 20:08:34 fslab1 kernel: [    1.190089] TCP: Hash tables configured (established 65536 bind 65536)
Jul 31 20:08:34 fslab1 kernel: [    1.196759] TCP: reno registered
Jul 31 20:08:34 fslab1 kernel: [    1.200067] UDP hash table entries: 4096 (order: 5, 131072 bytes)
Jul 31 20:08:34 fslab1 kernel: [    1.206307] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
Jul 31 20:08:34 fslab1 kernel: [    1.213101] NET: Registered protocol family 1
Jul 31 20:08:34 fslab1 kernel: [    1.217681] RPC: Registered named UNIX socket transport module.
Jul 31 20:08:34 fslab1 kernel: [    1.223669] RPC: Registered udp transport module.
Jul 31 20:08:34 fslab1 kernel: [    1.228432] RPC: Registered tcp transport module.
Jul 31 20:08:34 fslab1 kernel: [    1.233197] RPC: Registered tcp NFSv4.1 backchannel transport module.
Jul 31 20:08:34 fslab1 kernel: [    1.240128] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 22
Jul 31 20:08:34 fslab1 kernel: [    1.246433] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21
Jul 31 20:08:34 fslab1 kernel: [    1.252465] pci 0000:00:00.0: Found enabled HT MSI Mapping
Jul 31 20:08:34 fslab1 kernel: [    1.258025] pci 0000:00:0d.0: Found disabled HT MSI Mapping
Jul 31 20:08:34 fslab1 kernel: [    1.263669] pci 0000:00:00.0: Found enabled HT MSI Mapping
Jul 31 20:08:34 fslab1 kernel: [    1.269220] pci 0000:00:0d.0: Linking AER extended capability
Jul 31 20:08:34 fslab1 kernel: [    1.275065] pci 0000:00:00.0: Found enabled HT MSI Mapping
Jul 31 20:08:34 fslab1 kernel: [    1.280623] pci 0000:00:0e.0: Found disabled HT MSI Mapping
Jul 31 20:08:34 fslab1 kernel: [    1.286264] pci 0000:00:00.0: Found enabled HT MSI Mapping
Jul 31 20:08:34 fslab1 kernel: [    1.291813] pci 0000:00:0e.0: Linking AER extended capability
Jul 31 20:08:34 fslab1 kernel: [    1.297734] pci 0000:80:00.0: Found disabled HT MSI Mapping
Jul 31 20:08:34 fslab1 kernel: [    1.303368] pci 0000:80:0d.0: Enabling HT MSI Mapping
Jul 31 20:08:34 fslab1 kernel: [    1.308492] pci 0000:80:0d.0: Found enabled HT MSI Mapping
Jul 31 20:08:34 fslab1 kernel: [    1.314043] pci 0000:80:0d.0: Linking AER extended capability
Jul 31 20:08:34 fslab1 kernel: [    1.319881] pci 0000:80:00.0: Found disabled HT MSI Mapping
Jul 31 20:08:34 fslab1 kernel: [    1.325525] pci 0000:80:0e.0: Enabling HT MSI Mapping
Jul 31 20:08:34 fslab1 kernel: [    1.330642] pci 0000:80:0e.0: Found enabled HT MSI Mapping
Jul 31 20:08:34 fslab1 kernel: [    1.336195] pci 0000:80:0e.0: Linking AER extended capability
Jul 31 20:08:34 fslab1 kernel: [    1.342004] pci 0000:81:00.0: rerouting interrupts for [8086:0370]
Jul 31 20:08:34 fslab1 kernel: [    1.348247] pci 0000:81:00.2: rerouting interrupts for [8086:0372]
Jul 31 20:08:34 fslab1 kernel: [    1.354572] Unpacking initramfs...
Jul 31 20:08:34 fslab1 kernel: [    1.655909] Freeing initrd memory: 12628K (ffff88007f3a0000 - ffff88007fff5000)
Jul 31 20:08:34 fslab1 kernel: [    1.663966] PCI-DMA: Disabling AGP.
Jul 31 20:08:34 fslab1 kernel: [    1.667644] PCI-DMA: aperture base @ c0000000 size 65536 KB
Jul 31 20:08:34 fslab1 kernel: [    1.673282] PCI-DMA: using GART IOMMU.
Jul 31 20:08:34 fslab1 kernel: [    1.677100] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
Jul 31 20:08:34 fslab1 kernel: [    1.688613] audit: initializing netlink socket (disabled)
Jul 31 20:08:34 fslab1 kernel: [    1.694108] type=2000 audit(1375294092.692:1): initialized
Jul 31 20:08:34 fslab1 kernel: [    1.713587] bounce pool size: 64 pages
Jul 31 20:08:34 fslab1 kernel: [    1.717423] HugeTLB registered 2 MB page size, pre-allocated 0 pages
Jul 31 20:08:34 fslab1 kernel: [    1.724372] zbud: loaded
Jul 31 20:08:34 fslab1 kernel: [    1.728071] VFS: Disk quotas dquot_6.5.2
Jul 31 20:08:34 fslab1 kernel: [    1.732090] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Jul 31 20:08:34 fslab1 kernel: [    1.738841] NFS: Registering the id_resolver key type
Jul 31 20:08:34 fslab1 kernel: [    1.743971] Key type id_resolver registered
Jul 31 20:08:34 fslab1 kernel: [    1.748213] Key type id_legacy registered
Jul 31 20:08:34 fslab1 kernel: [    1.752304] msgmni has been set to 13853
Jul 31 20:08:34 fslab1 kernel: [    1.756673] alg: No test for stdrng (krng)
Jul 31 20:08:34 fslab1 kernel: [    1.760878] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
Jul 31 20:08:34 fslab1 kernel: [    1.768371] io scheduler noop registered
Jul 31 20:08:34 fslab1 kernel: [    1.772358] io scheduler deadline registered
Jul 31 20:08:34 fslab1 kernel: [    1.776713] io scheduler cfq registered (default)
Jul 31 20:08:34 fslab1 kernel: [    1.782154] GHES: HEST is not enabled!
Jul 31 20:08:34 fslab1 kernel: [    1.786043] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
Jul 31 20:08:34 fslab1 kernel: [    1.812687] 00:04: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Jul 31 20:08:34 fslab1 kernel: [    1.838689] 00:05: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Jul 31 20:08:34 fslab1 kernel: [    1.844697] Linux agpgart interface v0.103
Jul 31 20:08:34 fslab1 kernel: [    1.848981] i8042: PNP: No PS/2 controller found. Probing ports directly.
Jul 31 20:08:34 fslab1 kernel: [    1.857936] serio: i8042 KBD port at 0x60,0x64 irq 1
Jul 31 20:08:34 fslab1 kernel: [    1.862968] serio: i8042 AUX port at 0x60,0x64 irq 12
Jul 31 20:08:34 fslab1 kernel: [    1.868249] mousedev: PS/2 mouse device common for all mice
Jul 31 20:08:34 fslab1 kernel: [    1.873934] usbcore: registered new interface driver keyspan_remote
Jul 31 20:08:34 fslab1 kernel: [    1.880291] rtc_cmos 00:01: RTC can wake from S4
Jul 31 20:08:34 fslab1 kernel: [    1.885127] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
Jul 31 20:08:34 fslab1 kernel: [    1.891316] rtc_cmos 00:01: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
Jul 31 20:08:34 fslab1 kernel: [    1.898994] cpuidle: using governor ladder
Jul 31 20:08:34 fslab1 kernel: [    1.903155] cpuidle: using governor menu
Jul 31 20:08:34 fslab1 kernel: [    1.907219] drop_monitor: Initializing network drop monitor service
Jul 31 20:08:34 fslab1 kernel: [    1.913631] TCP: cubic registered
Jul 31 20:08:34 fslab1 kernel: [    1.917058] NET: Registered protocol family 10
Jul 31 20:08:34 fslab1 kernel: [    1.921814] mip6: Mobile IPv6
Jul 31 20:08:34 fslab1 kernel: [    1.924846] NET: Registered protocol family 17
Jul 31 20:08:34 fslab1 kernel: [    1.929387] Key type dns_resolver registered
Jul 31 20:08:34 fslab1 kernel: [    1.934040] registered taskstats version 1
Jul 31 20:08:34 fslab1 kernel: [    1.939145] rtc_cmos 00:01: setting system clock to 2013-07-31 18:08:14 UTC (1375294094)
Jul 31 20:08:34 fslab1 kernel: [    1.948695] Freeing unused kernel memory: 988K (ffffffff817da000 - ffffffff818d1000)
Jul 31 20:08:34 fslab1 kernel: [    2.106009] SCSI subsystem initialized
Jul 31 20:08:34 fslab1 kernel: [    2.115488] ACPI: bus type ATA registered
Jul 31 20:08:34 fslab1 kernel: [    2.188996] Floppy drive(s): fd0 is 1.44M
Jul 31 20:08:34 fslab1 kernel: [    2.194201] ACPI: PCI Interrupt Link [LTID] enabled at IRQ 20
Jul 31 20:08:34 fslab1 kernel: [    2.201286] sata_nv 0000:00:07.0: Using ADMA mode
Jul 31 20:08:34 fslab1 kernel: [    2.206240] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
Jul 31 20:08:34 fslab1 kernel: [    2.213403] e1000: Copyright (c) 1999-2006 Intel Corporation.
Jul 31 20:08:34 fslab1 kernel: [    2.219331] scsi0 : sata_nv
Jul 31 20:08:34 fslab1 kernel: [    2.223958] scsi1 : sata_nv
Jul 31 20:08:34 fslab1 kernel: [    2.224596] FDC 0 is a post-1991 82077
Jul 31 20:08:34 fslab1 kernel: [    2.231190] ata1: SATA max UDMA/133 cmd 0xc800 ctl 0xc400 bmdma 0xb800 irq 20
Jul 31 20:08:34 fslab1 kernel: [    2.238400] ata2: SATA max UDMA/133 cmd 0xc000 ctl 0xbc00 bmdma 0xb808 irq 20
Jul 31 20:08:34 fslab1 kernel: [    2.245626] e1000 0000:03:02.0: enabling device (0000 -> 0003)
Jul 31 20:08:34 fslab1 kernel: [    2.251764] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 19
Jul 31 20:08:34 fslab1 kernel: [    2.257996] ACPI: PCI Interrupt Link [LTIE] enabled at IRQ 21
Jul 31 20:08:34 fslab1 kernel: [    2.263813] sata_nv 0000:00:08.0: Using ADMA mode
Jul 31 20:08:34 fslab1 kernel: [    2.268950] scsi2 : sata_nv
Jul 31 20:08:34 fslab1 kernel: [    2.271903] scsi3 : sata_nv
Jul 31 20:08:34 fslab1 kernel: [    2.274851] ata3: SATA max UDMA/133 cmd 0xb400 ctl 0xb000 bmdma 0xa400 irq 21
Jul 31 20:08:34 fslab1 kernel: [    2.282057] ata4: SATA max UDMA/133 cmd 0xac00 ctl 0xa800 bmdma 0xa408 irq 21
Jul 31 20:08:34 fslab1 kernel: [    2.289611] ACPI: PCI Interrupt Link [LT3D] enabled at IRQ 47
Jul 31 20:08:34 fslab1 kernel: [    2.295435] sata_nv 0000:80:07.0: Using ADMA mode
Jul 31 20:08:34 fslab1 kernel: [    2.525162] scsi4 : sata_nv
Jul 31 20:08:34 fslab1 kernel: [    2.528129] scsi5 : sata_nv
Jul 31 20:08:34 fslab1 kernel: [    2.531064] ata5: SATA max UDMA/133 cmd 0xf800 ctl 0xf400 bmdma 0xe800 irq 47
Jul 31 20:08:34 fslab1 kernel: [    2.538268] ata6: SATA max UDMA/133 cmd 0xf000 ctl 0xec00 bmdma 0xe808 irq 47
Jul 31 20:08:34 fslab1 kernel: [    2.545874] scsi6 : pata_amd
Jul 31 20:08:34 fslab1 kernel: [    2.549228] scsi7 : pata_amd
Jul 31 20:08:34 fslab1 kernel: [    2.552533] ata7: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x3000 irq 14
Jul 31 20:08:34 fslab1 kernel: [    2.559562] ata8: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x3008 irq 15
Jul 31 20:08:34 fslab1 kernel: [    2.566907] ACPI: PCI Interrupt Link [LT2E] enabled at IRQ 46
Jul 31 20:08:34 fslab1 kernel: [    2.576024] ata1: SATA link down (SStatus 0 SControl 300)
Jul 31 20:08:34 fslab1 kernel: [    2.579853] sata_nv 0000:80:08.0: Using ADMA mode
Jul 31 20:08:34 fslab1 kernel: [    2.580211] scsi8 : sata_nv
Jul 31 20:08:34 fslab1 kernel: [    2.580301] scsi9 : sata_nv
Jul 31 20:08:34 fslab1 kernel: [    2.580375] ata9: SATA max UDMA/133 cmd 0xe400 ctl 0xe000 bmdma 0xd400 irq 46
Jul 31 20:08:34 fslab1 kernel: [    2.580377] ata10: SATA max UDMA/133 cmd 0xdc00 ctl 0xd800 bmdma 0xd408 irq 46
Jul 31 20:08:34 fslab1 kernel: [    2.714106] e1000 0000:03:02.0 eth0: (PCI:33MHz:32-bit) 00:0e:0c:b8:c7:59
Jul 31 20:08:34 fslab1 kernel: [    2.720969] e1000 0000:03:02.0 eth0: Intel(R) PRO/1000 Network Connection
Jul 31 20:08:34 fslab1 kernel: [    2.741599] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Jul 31 20:08:34 fslab1 kernel: [    2.760039] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Jul 31 20:08:34 fslab1 kernel: [    2.806774] ata3.00: ATA-7: ST3808110AS, 3.AAE, max UDMA/133
Jul 31 20:08:34 fslab1 kernel: [    2.812496] ata3.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 31/32)
Jul 31 20:08:34 fslab1 kernel: [    2.856018] ata5: SATA link down (SStatus 0 SControl 300)
Jul 31 20:08:34 fslab1 kernel: [    2.881741] ata3.00: configured for UDMA/133
Jul 31 20:08:34 fslab1 kernel: [    2.888017] ata9: SATA link down (SStatus 0 SControl 300)
Jul 31 20:08:34 fslab1 kernel: [    2.916015] ata2: SATA link down (SStatus 0 SControl 300)
Jul 31 20:08:34 fslab1 kernel: [    2.921630] scsi 2:0:0:0: Direct-Access     ATA      ST3808110AS      3.AA PQ: 0 ANSI: 5
Jul 31 20:08:34 fslab1 kernel: [    2.929821] ata3: DMA mask 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
Jul 31 20:08:34 fslab1 kernel: [    2.978730] scsi 2:0:0:0: Attached scsi generic sg0 type 0
Jul 31 20:08:34 fslab1 kernel: [    3.252021] ata4: SATA link down (SStatus 0 SControl 300)
Jul 31 20:08:34 fslab1 kernel: [    3.568016] ata6: SATA link down (SStatus 0 SControl 300)
Jul 31 20:08:34 fslab1 kernel: [    4.048016] ata10: SATA link down (SStatus 0 SControl 300)
Jul 31 20:08:34 fslab1 kernel: [    6.773704] e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
Jul 31 20:08:34 fslab1 kernel: [    6.781132] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Jul 31 20:08:34 fslab1 kernel: [    9.265986] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist.
Jul 31 20:08:34 fslab1 kernel: [    9.453482] fuse init (API version 7.22)
Jul 31 20:08:34 fslab1 kernel: [   10.290548] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jul 31 20:08:34 fslab1 kernel: [   10.310898] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jul 31 20:08:34 fslab1 kernel: [   10.327763] ohci-pci: OHCI PCI platform driver
Jul 31 20:08:34 fslab1 kernel: [   10.332633] ohci-pci 0000:00:02.0: OHCI PCI host controller
Jul 31 20:08:34 fslab1 kernel: [   10.338316] ohci-pci 0000:00:02.0: new USB bus registered, assigned bus number 1
Jul 31 20:08:34 fslab1 kernel: [   10.349119] ohci-pci 0000:00:02.0: irq 22, io mem 0xce3fb000
Jul 31 20:08:34 fslab1 kernel: [   10.386389] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
Jul 31 20:08:34 fslab1 kernel: [   10.396640] ACPI: Power Button [PWRB]
Jul 31 20:08:34 fslab1 kernel: [   10.410050] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
Jul 31 20:08:34 fslab1 kernel: [   10.416922] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul 31 20:08:34 fslab1 kernel: [   10.424358] usb usb1: Product: OHCI PCI host controller
Jul 31 20:08:34 fslab1 kernel: [   10.429652] usb usb1: Manufacturer: Linux 3.11.0-rc1+ ohci_hcd
Jul 31 20:08:34 fslab1 kernel: [   10.435671] usb usb1: SerialNumber: 0000:00:02.0
Jul 31 20:08:34 fslab1 kernel: [   10.444386] hub 1-0:1.0: USB hub found
Jul 31 20:08:34 fslab1 kernel: [   10.444467] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
Jul 31 20:08:34 fslab1 kernel: [   10.444473] ACPI: Power Button [PWRF]
Jul 31 20:08:34 fslab1 kernel: [   10.461485] hub 1-0:1.0: 10 ports detected
Jul 31 20:08:34 fslab1 kernel: [   10.467594] ACPI Warning: 0x0000000000004c00-0x0000000000004c3f SystemIO conflicts with Region \_SB_.PCI0.SMBU.SMRG 1 (20130517/utaddress-251)
Jul 31 20:08:34 fslab1 kernel: [   10.480723] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
Jul 31 20:08:34 fslab1 kernel: [   10.491140] i2c i2c-0: nForce2 SMBus adapter at 0x4c40
Jul 31 20:08:34 fslab1 kernel: [   10.502302] ehci-pci: EHCI PCI platform driver
Jul 31 20:08:34 fslab1 kernel: [   10.511877] ehci-pci 0000:00:02.1: EHCI Host Controller
Jul 31 20:08:34 fslab1 kernel: [   10.517916] ehci-pci 0000:00:02.1: new USB bus registered, assigned bus number 2
Jul 31 20:08:34 fslab1 kernel: [   10.525748] ehci-pci 0000:00:02.1: debug port 1
Jul 31 20:08:34 fslab1 kernel: [   10.532191] ehci-pci 0000:00:02.1: irq 21, io mem 0xce3e0000
Jul 31 20:08:34 fslab1 kernel: [   10.548033] ehci-pci 0000:00:02.1: USB 2.0 started, EHCI 1.00
Jul 31 20:08:34 fslab1 kernel: [   10.554173] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
Jul 31 20:08:34 fslab1 kernel: [   10.561040] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul 31 20:08:34 fslab1 kernel: [   10.568495] usb usb2: Product: EHCI Host Controller
Jul 31 20:08:34 fslab1 kernel: [   10.573444] usb usb2: Manufacturer: Linux 3.11.0-rc1+ ehci_hcd
Jul 31 20:08:34 fslab1 kernel: [   10.579476] usb usb2: SerialNumber: 0000:00:02.1
Jul 31 20:08:34 fslab1 kernel: [   10.586237] hub 2-0:1.0: USB hub found
Jul 31 20:08:34 fslab1 kernel: [   10.590358] hub 2-0:1.0: 10 ports detected
Jul 31 20:08:34 fslab1 kernel: [   10.596130] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Jul 31 20:08:34 fslab1 kernel: [   10.615412] EDAC MC: Ver: 3.0.0
Jul 31 20:08:34 fslab1 kernel: [   10.631605] microcode: AMD CPU family 0xf not supported
Jul 31 20:08:34 fslab1 kernel: [   10.632102] MCE: In-kernel MCE decoding enabled.
Jul 31 20:08:34 fslab1 kernel: [   10.651281] AMD64 EDAC driver v3.4.0
Jul 31 20:08:34 fslab1 kernel: [   10.655993] ib_mthca: Mellanox InfiniBand HCA driver v1.0 (April 4, 2008)
Jul 31 20:08:34 fslab1 kernel: [   10.663005] ib_mthca: Initializing 0000:01:00.0
Jul 31 20:08:34 fslab1 kernel: [   10.667805] hub 1-0:1.0: USB hub found
Jul 31 20:08:34 fslab1 kernel: [   10.671747] hub 1-0:1.0: 10 ports detected
Jul 31 20:08:34 fslab1 kernel: [   10.676493] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 18
Jul 31 20:08:34 fslab1 kernel: [   10.694669] [Firmware Bug]: powernow-k8: No compatible ACPI _PSS objects found.
Jul 31 20:08:34 fslab1 kernel: [   10.694669] [Firmware Bug]: powernow-k8: First, make sure Cool'N'Quiet is enabled in the BIOS.
Jul 31 20:08:34 fslab1 kernel: [   10.694669] [Firmware Bug]: powernow-k8: If that doesn't help, try upgrading your BIOS.
Jul 31 20:08:34 fslab1 kernel: [   10.718812] microcode: AMD CPU family 0xf not supported
Jul 31 20:08:34 fslab1 kernel: [   10.727616] input: PC Speaker as /devices/platform/pcspkr/input/input2
Jul 31 20:08:34 fslab1 kernel: [   10.745647] sd 2:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
Jul 31 20:08:34 fslab1 kernel: [   10.754107] [Firmware Bug]: powernow-k8: No compatible ACPI _PSS objects found.
Jul 31 20:08:34 fslab1 kernel: [   10.754107] [Firmware Bug]: powernow-k8: First, make sure Cool'N'Quiet is enabled in the BIOS.
Jul 31 20:08:34 fslab1 kernel: [   10.754107] [Firmware Bug]: powernow-k8: If that doesn't help, try upgrading your BIOS.
Jul 31 20:08:34 fslab1 kernel: [   10.754396] sd 2:0:0:0: [sda] Write Protect is off
Jul 31 20:08:34 fslab1 kernel: [   10.754421] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Jul 31 20:08:34 fslab1 kernel: [   10.822492]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
Jul 31 20:08:34 fslab1 kernel: [   10.829826] sd 2:0:0:0: [sda] Attached SCSI disk
Jul 31 20:08:34 fslab1 kernel: [   13.135832] EDAC amd64: DRAM ECC enabled.
Jul 31 20:08:34 fslab1 kernel: [   13.139917] EDAC amd64: K8 revE or earlier detected (node 0).
Jul 31 20:08:34 fslab1 kernel: [   13.145774] EDAC amd64: CS0: Registered Double data rate SDRAM
Jul 31 20:08:34 fslab1 kernel: [   13.151669] EDAC amd64: CS2: Registered Double data rate SDRAM
Jul 31 20:08:34 fslab1 kernel: [   13.157706] EDAC MC0: Giving out device to 'amd64_edac' 'K8': DEV 0000:00:18.2
Jul 31 20:08:34 fslab1 kernel: [   13.165947] EDAC amd64: DRAM ECC enabled.
Jul 31 20:08:34 fslab1 kernel: [   13.170065] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Jul 31 20:08:34 fslab1 kernel: [   13.176865] EDAC amd64: K8 revE or earlier detected (node 1).
Jul 31 20:08:34 fslab1 kernel: [   13.182728] EDAC amd64: CS0: Registered Double data rate SDRAM
Jul 31 20:08:34 fslab1 kernel: [   13.188639] EDAC amd64: CS2: Registered Double data rate SDRAM
Jul 31 20:08:34 fslab1 kernel: [   13.194904] EDAC MC1: Giving out device to 'amd64_edac' 'K8': DEV 0000:00:19.2
Jul 31 20:08:34 fslab1 kernel: [   13.202318] EDAC PCI0: Giving out device to module 'amd64_edac' controller 'EDAC PCI controller': DEV '0000:00:18.2' (POLLED)
Jul 31 20:08:34 fslab1 kernel: [   14.155673] loop: module loaded
Jul 31 20:08:34 fslab1 kernel: [   14.196967] netif_napi_add() called with weight 100 on device 
Jul 31 20:08:34 fslab1 kernel: [   16.334799] device-mapper: uevent: version 1.0.3
Jul 31 20:08:34 fslab1 kernel: [   16.339905] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: dm-devel@xxxxxxxxxx
Jul 31 20:08:34 fslab1 kernel: [   17.809080] Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
Jul 31 20:08:43 fslab1 kernel: [   31.408701] rc.local (3571): /proc/319/oom_adj is deprecated, please use /proc/319/oom_score_adj instead.
Jul 31 20:08:43 fslab1 kernel: [   31.433045] IPv6: ADDRCONF(NETDEV_UP): ib0: link is not ready
Jul 31 20:08:44 fslab1 kernel: [   31.439754] IPv6: ADDRCONF(NETDEV_CHANGE): ib0: link becomes ready
Jul 31 20:12:30 fslab1 kernel: [  258.324616] ACPI: PCI Interrupt Link [LN2A] enabled at IRQ 43
Jul 31 20:12:30 fslab1 kernel: [  258.330738] Error handler scsi_eh_10 sleeping
Jul 31 20:12:30 fslab1 kernel: [  258.344062] Areca RAID Controller10: F/W V1.46 2009-01-06 & Model ARC-1260
Jul 31 20:12:30 fslab1 kernel: [  258.364021] scsi10 : Areca SATA Host Adapter RAID Controller( RAID6 capable)
Jul 31 20:12:30 fslab1 kernel: [  258.364021]  Driver Version 1.20.00.15 2010/08/05
Jul 31 20:12:31 fslab1 kernel: [  258.376015] scsi host10: scsi_scan_host_selected: <4294967295:4294967295:4294967295>
Jul 31 20:12:31 fslab1 kernel: [  258.383880] scsi 10:0:0:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:31 fslab1 kernel: [  258.389914] scsi 10:0:0:0: Send: 
Jul 31 20:12:31 fslab1 kernel: [  258.393275] 0xffff88007feff180 
Jul 31 20:12:31 fslab1 kernel: [  258.396524] scsi 10:0:0:0: CDB: 
Jul 31 20:12:31 fslab1 kernel: [  258.399789] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:31 fslab1 kernel: [  258.403916] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:31 fslab1 kernel: [  258.411879] leaving scsi_dispatch_cmnd()
Jul 31 20:12:31 fslab1 kernel: [  258.415852] scsi 10:0:0:0: Done: 
Jul 31 20:12:31 fslab1 kernel: [  258.419208] 0xffff88007feff180 SUCCESS
Jul 31 20:12:31 fslab1 kernel: [  258.423035] scsi 10:0:0:0:  
Jul 31 20:12:31 fslab1 kernel: [  258.425949] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Jul 31 20:12:31 fslab1 kernel: [  258.432007] scsi 10:0:0:0: CDB: 
Jul 31 20:12:31 fslab1 kernel: [  258.435266] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:31 fslab1 kernel: [  258.439394] scsi 10:0:0:0: scsi host busy 1 failed 0
Jul 31 20:12:31 fslab1 kernel: [  258.444423] scsi 10:0:0:0: Notifying upper driver of completion (result 10000)
Jul 31 20:12:31 fslab1 kernel: [  258.451736] 0 sectors total, 36 bytes done.
Jul 31 20:12:31 fslab1 kernel: [  258.456119] scsi scan: INQUIRY failed with code 0x10000
Jul 31 20:12:31 fslab1 kernel: [  258.461571] scsi 10:0:1:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:31 fslab1 kernel: [  258.467602] scsi 10:0:1:0: Send: 
Jul 31 20:12:31 fslab1 kernel: [  258.471002] 0xffff88007feff180 
Jul 31 20:12:31 fslab1 kernel: [  258.474244] scsi 10:0:1:0: CDB: 
Jul 31 20:12:31 fslab1 kernel: [  258.477535] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:31 fslab1 kernel: [  258.481684] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:31 fslab1 kernel: [  258.489694] leaving scsi_dispatch_cmnd()
Jul 31 20:12:31 fslab1 kernel: [  258.493691] scsi 10:0:1:0: Done: 
Jul 31 20:12:31 fslab1 kernel: [  258.497071] 0xffff88007feff180 SUCCESS
Jul 31 20:12:31 fslab1 kernel: [  258.500932] scsi 10:0:1:0:  
Jul 31 20:12:31 fslab1 kernel: [  258.503870] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:31 fslab1 kernel: [  258.509248] scsi 10:0:1:0: CDB: 
Jul 31 20:12:33 fslab1 kernel: [  258.512537] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:33 fslab1 kernel: [  258.516684] scsi 10:0:1:0: scsi host busy 1 failed 0
Jul 31 20:12:33 fslab1 kernel: [  258.521715] scsi 10:0:1:0: Notifying upper driver of completion (result 0)
Jul 31 20:12:33 fslab1 kernel: [  258.528658] 0 sectors total, 36 bytes done.
Jul 31 20:12:33 fslab1 kernel: [  258.532955] scsi scan: INQUIRY successful with code 0x0
Jul 31 20:12:33 fslab1 kernel: [  258.538263] scsi 10:0:1:0: scsi scan: INQUIRY pass 2 length 96
Jul 31 20:12:33 fslab1 kernel: [  258.544302] scsi 10:0:1:0: Send: 
Jul 31 20:12:33 fslab1 kernel: [  258.547673] 0xffff88007feff180 
Jul 31 20:12:33 fslab1 kernel: [  258.550923] scsi 10:0:1:0: CDB: 
Jul 31 20:12:33 fslab1 kernel: [  258.554214] Inquiry: 12 00 00 00 60 00
Jul 31 20:12:33 fslab1 kernel: [  258.558361] buffer = 0xffff8800bebf4ec0, bufflen = 96, queuecommand 0xffffffffa029a350
Jul 31 20:12:33 fslab1 kernel: [  258.566372] leaving scsi_dispatch_cmnd()
Jul 31 20:12:33 fslab1 kernel: [  258.570370] scsi 10:0:1:0: Done: 
Jul 31 20:12:33 fslab1 kernel: [  258.573747] 0xffff88007feff180 SUCCESS
Jul 31 20:12:33 fslab1 kernel: [  258.577593] scsi 10:0:1:0:  
Jul 31 20:12:33 fslab1 kernel: [  258.580534] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:33 fslab1 kernel: [  258.585908] scsi 10:0:1:0: CDB: 
Jul 31 20:12:33 fslab1 kernel: [  258.589198] Inquiry: 12 00 00 00 60 00
Jul 31 20:12:33 fslab1 kernel: [  258.593338] scsi 10:0:1:0: scsi host busy 1 failed 0
Jul 31 20:12:33 fslab1 kernel: [  258.598367] scsi 10:0:1:0: Notifying upper driver of completion (result 0)
Jul 31 20:12:33 fslab1 kernel: [  258.605309] 0 sectors total, 96 bytes done.
Jul 31 20:12:33 fslab1 kernel: [  258.609574] scsi scan: INQUIRY successful with code 0x0
Jul 31 20:12:33 fslab1 kernel: [  258.614905] scsi 10:0:1:0: scsi scan: peripheral qualifier of 3, device not added
Jul 31 20:12:33 fslab1 kernel: [  258.622479] scsi 10:0:1:0: scsi scan: consider passing scsi_mod.dev_flags=Hitachi:HDS724040KLSA80:0x240 or 0x1000240
Jul 31 20:12:33 fslab1 kernel: [  258.633125] scsi scan: Sending REPORT LUNS to host 10 channel 0 id 1 (try 0)
Jul 31 20:12:33 fslab1 kernel: [  258.640252] scsi 10:0:1:0: Send: 
Jul 31 20:12:33 fslab1 kernel: [  258.643626] 0xffff88007feff180 
Jul 31 20:12:33 fslab1 kernel: [  258.646874] scsi 10:0:1:0: CDB: 
Jul 31 20:12:33 fslab1 kernel: [  258.650167] Report luns: a0 00 00 00 00 00 00 00 10 00 00 00
Jul 31 20:12:33 fslab1 kernel: [  258.656481] buffer = 0xffff8800bebf4ec0, bufflen = 4096, queuecommand 0xffffffffa029a350
Jul 31 20:12:33 fslab1 kernel: [  258.664667] leaving scsi_dispatch_cmnd()
Jul 31 20:12:33 fslab1 kernel: [  258.668659] scsi 10:0:1:0: Done: 
Jul 31 20:12:33 fslab1 kernel: [  258.672036] 0xffff88007feff180 SUCCESS
Jul 31 20:12:33 fslab1 kernel: [  258.675888] scsi 10:0:1:0:  
Jul 31 20:12:33 fslab1 kernel: [  258.678828] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:33 fslab1 kernel: [  258.684202] scsi 10:0:1:0: CDB: 
Jul 31 20:12:33 fslab1 kernel: [  258.687486] Report luns: a0 00 00 00 00 00 00 00 10 00 00 00
Jul 31 20:12:33 fslab1 kernel: [  258.693807] scsi 10:0:1:0: scsi host busy 1 failed 0
Jul 31 20:12:33 fslab1 kernel: [  258.698837] scsi 10:0:1:0: Notifying upper driver of completion (result 0)
Jul 31 20:12:33 fslab1 kernel: [  258.705778] 8 sectors total, 4096 bytes done.
Jul 31 20:12:33 fslab1 kernel: [  258.710221] scsi scan: REPORT LUNS successful (try 0) result 0x0
Jul 31 20:12:33 fslab1 kernel: [  258.716299] scsi 10:0:1:0: scsi scan: REPORT LUN scan
Jul 31 20:12:33 fslab1 kernel: [  258.721474] scsi 10:0:1:5: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:33 fslab1 kernel: [  258.727419] scsi 10:0:1:5: Send: 
Jul 31 20:12:33 fslab1 kernel: [  258.730820] 0xffff88007feff180 
Jul 31 20:12:33 fslab1 kernel: [  258.734070] scsi 10:0:1:5: CDB: 
Jul 31 20:12:33 fslab1 kernel: [  258.737359] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:33 fslab1 kernel: [  258.741500] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:33 fslab1 kernel: [  258.749510] leaving scsi_dispatch_cmnd()
Jul 31 20:12:33 fslab1 kernel: [  258.753507] scsi 10:0:1:5: Done: 
Jul 31 20:12:33 fslab1 kernel: [  258.756886] 0xffff88007feff180 SUCCESS
Jul 31 20:12:33 fslab1 kernel: [  258.760736] scsi 10:0:1:5:  
Jul 31 20:12:33 fslab1 kernel: [  258.763669] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:33 fslab1 kernel: [  258.769049] scsi 10:0:1:5: CDB: 
Jul 31 20:12:33 fslab1 kernel: [  258.772335] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:33 fslab1 kernel: [  258.776476] scsi 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:33 fslab1 kernel: [  258.781507] scsi 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:33 fslab1 kernel: [  258.788448] 0 sectors total, 36 bytes done.
Jul 31 20:12:33 fslab1 kernel: [  258.792713] scsi scan: INQUIRY successful with code 0x0
Jul 31 20:12:33 fslab1 kernel: [  258.798037] scsi 10:0:1:5: scsi scan: INQUIRY pass 2 length 96
Jul 31 20:12:34 fslab1 kernel: [  258.803951] scsi 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  258.807328] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  258.810565] scsi 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  258.813857] Inquiry: 12 00 00 00 60 00
Jul 31 20:12:34 fslab1 kernel: [  258.818005] buffer = 0xffff8800bebf4ec0, bufflen = 96, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  258.826016] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  258.830012] scsi 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  258.833390] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  258.837236] scsi 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  258.840178] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  258.845552] scsi 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  258.848839] Inquiry: 12 00 00 00 60 00
Jul 31 20:12:34 fslab1 kernel: [  258.852988] scsi 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  258.858020] scsi 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  258.864961] 0 sectors total, 96 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  258.869224] scsi scan: INQUIRY successful with code 0x0
Jul 31 20:12:34 fslab1 kernel: [  258.874519] scsi 10:0:1:5: Direct-Access     Hitachi  HDS724040KLSA80  R001 PQ: 0 ANSI: 5
Jul 31 20:12:34 fslab1 kernel: [  258.882816] scsi 10:0:2:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:34 fslab1 kernel: [  258.888722] scsi 10:0:2:0: Send: 
Jul 31 20:12:34 fslab1 kernel: [  258.892098] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  258.895334] scsi 10:0:2:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  258.898626] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  258.902773] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  258.910785] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  258.914778] scsi 10:0:2:0: Done: 
Jul 31 20:12:34 fslab1 kernel: [  258.918152] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  258.921996] scsi 10:0:2:0:  
Jul 31 20:12:34 fslab1 kernel: [  258.924939] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  258.931008] scsi 10:0:2:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  258.934294] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  258.938444] scsi 10:0:2:0: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  258.943474] scsi 10:0:2:0: Notifying upper driver of completion (result 10000)
Jul 31 20:12:34 fslab1 kernel: [  258.950787] 0 sectors total, 36 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  258.955121] scsi scan: INQUIRY failed with code 0x10000
Jul 31 20:12:34 fslab1 kernel: [  258.960477] scsi 10:0:3:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:34 fslab1 kernel: [  258.966418] scsi 10:0:3:0: Send: 
Jul 31 20:12:34 fslab1 kernel: [  258.969819] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  258.973069] scsi 10:0:3:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  258.976359] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  258.980500] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  258.988512] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  258.992508] scsi 10:0:3:0: Done: 
Jul 31 20:12:34 fslab1 kernel: [  258.995883] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  258.999733] scsi 10:0:3:0:  
Jul 31 20:12:34 fslab1 kernel: [  259.002674] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  259.008744] scsi 10:0:3:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.012032] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.016192] scsi 10:0:3:0: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  259.021218] scsi 10:0:3:0: Notifying upper driver of completion (result 10000)
Jul 31 20:12:34 fslab1 kernel: [  259.028531] 0 sectors total, 36 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  259.032826] scsi scan: INQUIRY failed with code 0x10000
Jul 31 20:12:34 fslab1 kernel: [  259.038170] scsi 10:0:4:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:34 fslab1 kernel: [  259.044081] scsi 10:0:4:0: Send: 
Jul 31 20:12:34 fslab1 kernel: [  259.047453] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  259.050702] scsi 10:0:4:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.053994] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.058133] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  259.066145] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  259.070138] scsi 10:0:4:0: Done: 
Jul 31 20:12:34 fslab1 kernel: [  259.073511] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  259.077356] scsi 10:0:4:0:  
Jul 31 20:12:34 fslab1 kernel: [  259.080297] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  259.086367] scsi 10:0:4:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.089653] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.093810] scsi 10:0:4:0: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  259.098841] scsi 10:0:4:0: Notifying upper driver of completion (result 10000)
Jul 31 20:12:34 fslab1 kernel: [  259.106155] 0 sectors total, 36 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  259.110408] scsi scan: INQUIRY failed with code 0x10000
Jul 31 20:12:34 fslab1 kernel: [  259.115724] scsi 10:0:5:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:34 fslab1 kernel: [  259.122501] scsi 10:0:5:0: Send: 
Jul 31 20:12:34 fslab1 kernel: [  259.125880] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  259.129131] scsi 10:0:5:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.132422] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.136571] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  259.144583] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  259.148579] scsi 10:0:5:0: Done: 
Jul 31 20:12:34 fslab1 kernel: [  259.151955] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  259.155804] scsi 10:0:5:0:  
Jul 31 20:12:34 fslab1 kernel: [  259.158748] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  259.164824] scsi 10:0:5:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.168109] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.172267] scsi 10:0:5:0: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  259.177299] scsi 10:0:5:0: Notifying upper driver of completion (result 10000)
Jul 31 20:12:34 fslab1 kernel: [  259.184611] 0 sectors total, 36 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  259.188888] scsi scan: INQUIRY failed with code 0x10000
Jul 31 20:12:34 fslab1 kernel: [  259.194231] scsi 10:0:6:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:34 fslab1 kernel: [  259.200145] scsi 10:0:6:0: Send: 
Jul 31 20:12:34 fslab1 kernel: [  259.203514] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  259.206765] scsi 10:0:6:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.210055] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.214203] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  259.222215] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  259.226208] scsi 10:0:6:0: Done: 
Jul 31 20:12:34 fslab1 kernel: [  259.229582] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  259.233436] scsi 10:0:6:0:  
Jul 31 20:12:34 fslab1 kernel: [  259.236377] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  259.242447] scsi 10:0:6:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.245732] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.249873] scsi 10:0:6:0: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  259.254904] scsi 10:0:6:0: Notifying upper driver of completion (result 10000)
Jul 31 20:12:34 fslab1 kernel: [  259.262217] 0 sectors total, 36 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  259.266494] scsi scan: INQUIRY failed with code 0x10000
Jul 31 20:12:34 fslab1 kernel: [  259.271851] scsi 10:0:7:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:34 fslab1 kernel: [  259.277794] scsi 10:0:7:0: Send: 
Jul 31 20:12:34 fslab1 kernel: [  259.281189] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  259.284439] scsi 10:0:7:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.287726] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.291879] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  259.299892] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  259.303887] scsi 10:0:7:0: Done: 
Jul 31 20:12:34 fslab1 kernel: [  259.307266] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  259.311111] scsi 10:0:7:0:  
Jul 31 20:12:34 fslab1 kernel: [  259.314053] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  259.320124] scsi 10:0:7:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.323405] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.327557] scsi 10:0:7:0: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  259.332589] scsi 10:0:7:0: Notifying upper driver of completion (result 10000)
Jul 31 20:12:34 fslab1 kernel: [  259.339900] 0 sectors total, 36 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  259.344160] scsi scan: INQUIRY failed with code 0x10000
Jul 31 20:12:34 fslab1 kernel: [  259.349497] scsi 10:0:8:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:34 fslab1 kernel: [  259.355409] scsi 10:0:8:0: Send: 
Jul 31 20:12:34 fslab1 kernel: [  259.358784] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  259.362020] scsi 10:0:8:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.365310] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.369460] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  259.377470] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  259.381463] scsi 10:0:8:0: Done: 
Jul 31 20:12:34 fslab1 kernel: [  259.384836] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  259.388689] scsi 10:0:8:0:  
Jul 31 20:12:34 fslab1 kernel: [  259.391630] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  259.397705] scsi 10:0:8:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.400998] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.405154] scsi 10:0:8:0: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  259.410186] scsi 10:0:8:0: Notifying upper driver of completion (result 10000)
Jul 31 20:12:34 fslab1 kernel: [  259.417497] 0 sectors total, 36 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  259.421744] scsi scan: INQUIRY failed with code 0x10000
Jul 31 20:12:34 fslab1 kernel: [  259.427067] scsi 10:0:9:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:34 fslab1 kernel: [  259.432977] scsi 10:0:9:0: Send: 
Jul 31 20:12:34 fslab1 kernel: [  259.436366] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  259.439609] scsi 10:0:9:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.442901] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.447049] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  259.455060] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  259.459057] scsi 10:0:9:0: Done: 
Jul 31 20:12:34 fslab1 kernel: [  259.462435] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  259.466280] scsi 10:0:9:0:  
Jul 31 20:12:34 fslab1 kernel: [  259.469222] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  259.475292] scsi 10:0:9:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.478577] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.482727] scsi 10:0:9:0: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  259.487757] scsi 10:0:9:0: Notifying upper driver of completion (result 10000)
Jul 31 20:12:34 fslab1 kernel: [  259.495069] 0 sectors total, 36 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  259.499327] scsi scan: INQUIRY failed with code 0x10000
Jul 31 20:12:34 fslab1 kernel: [  259.504665] scsi 10:0:10:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:34 fslab1 kernel: [  259.510664] scsi 10:0:10:0: Send: 
Jul 31 20:12:34 fslab1 kernel: [  259.514126] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  259.517362] scsi 10:0:10:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.520740] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.524888] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  259.532899] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  259.536892] scsi 10:0:10:0: Done: 
Jul 31 20:12:34 fslab1 kernel: [  259.540353] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  259.544210] scsi 10:0:10:0:  
Jul 31 20:12:34 fslab1 kernel: [  259.547232] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  259.553305] scsi 10:0:10:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.556679] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.560817] scsi 10:0:10:0: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  259.565935] scsi 10:0:10:0: Notifying upper driver of completion (result 10000)
Jul 31 20:12:34 fslab1 kernel: [  259.573335] 0 sectors total, 36 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  259.577611] scsi scan: INQUIRY failed with code 0x10000
Jul 31 20:12:34 fslab1 kernel: [  259.582974] scsi 10:0:11:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:34 fslab1 kernel: [  259.588969] scsi 10:0:11:0: Send: 
Jul 31 20:12:34 fslab1 kernel: [  259.592451] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  259.595690] scsi 10:0:11:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.599066] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.603214] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  259.611224] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  259.615222] scsi 10:0:11:0: Done: 
Jul 31 20:12:34 fslab1 kernel: [  259.618686] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  259.622542] scsi 10:0:11:0:  
Jul 31 20:12:34 fslab1 kernel: [  259.625571] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  259.631641] scsi 10:0:11:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.635013] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.639162] scsi 10:0:11:0: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  259.644279] scsi 10:0:11:0: Notifying upper driver of completion (result 10000)
Jul 31 20:12:34 fslab1 kernel: [  259.651678] 0 sectors total, 36 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  259.655948] scsi scan: INQUIRY failed with code 0x10000
Jul 31 20:12:34 fslab1 kernel: [  259.661285] scsi 10:0:12:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:34 fslab1 kernel: [  259.667289] scsi 10:0:12:0: Send: 
Jul 31 20:12:34 fslab1 kernel: [  259.670763] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  259.674015] scsi 10:0:12:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.677414] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.681635] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  259.689651] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  259.693655] scsi 10:0:12:0: Done: 
Jul 31 20:12:34 fslab1 kernel: [  259.697121] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  259.700980] scsi 10:0:12:0:  
Jul 31 20:12:34 fslab1 kernel: [  259.704010] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  259.710079] scsi 10:0:12:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.713450] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.717598] scsi 10:0:12:0: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  259.722718] scsi 10:0:12:0: Notifying upper driver of completion (result 10000)
Jul 31 20:12:34 fslab1 kernel: [  259.730117] 0 sectors total, 36 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  259.734370] scsi scan: INQUIRY failed with code 0x10000
Jul 31 20:12:34 fslab1 kernel: [  259.739700] scsi 10:0:13:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:34 fslab1 kernel: [  259.745696] scsi 10:0:13:0: Send: 
Jul 31 20:12:34 fslab1 kernel: [  259.749183] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  259.752435] scsi 10:0:13:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.755809] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.760214] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  259.768283] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  259.772344] scsi 10:0:13:0: Done: 
Jul 31 20:12:34 fslab1 kernel: [  259.775806] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  259.779653] scsi 10:0:13:0:  
Jul 31 20:12:34 fslab1 kernel: [  259.782680] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  259.788751] scsi 10:0:13:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.792123] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.796280] scsi 10:0:13:0: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  259.801397] scsi 10:0:13:0: Notifying upper driver of completion (result 10000)
Jul 31 20:12:34 fslab1 kernel: [  259.808798] 0 sectors total, 36 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  259.813150] scsi scan: INQUIRY failed with code 0x10000
Jul 31 20:12:34 fslab1 kernel: [  259.818550] scsi 10:0:14:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:34 fslab1 kernel: [  259.824543] scsi 10:0:14:0: Send: 
Jul 31 20:12:34 fslab1 kernel: [  259.828015] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  259.831256] scsi 10:0:14:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.834634] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.838789] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  259.846800] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  259.850793] scsi 10:0:14:0: Done: 
Jul 31 20:12:34 fslab1 kernel: [  259.854254] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  259.858988] scsi 10:0:14:0:  
Jul 31 20:12:34 fslab1 kernel: [  259.862012] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  259.868083] scsi 10:0:14:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.871451] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.875604] scsi 10:0:14:0: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  259.880721] scsi 10:0:14:0: Notifying upper driver of completion (result 10000)
Jul 31 20:12:34 fslab1 kernel: [  259.888120] 0 sectors total, 36 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  259.892390] scsi scan: INQUIRY failed with code 0x10000
Jul 31 20:12:34 fslab1 kernel: [  259.897723] scsi 10:0:15:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:34 fslab1 kernel: [  259.903755] scsi 10:0:15:0: Send: 
Jul 31 20:12:34 fslab1 kernel: [  259.907246] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  259.910499] scsi 10:0:15:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.913878] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.918025] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  259.926036] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  259.930033] scsi 10:0:15:0: Done: 
Jul 31 20:12:34 fslab1 kernel: [  259.933498] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  259.937353] scsi 10:0:15:0:  
Jul 31 20:12:34 fslab1 kernel: [  259.940382] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  259.946452] scsi 10:0:15:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.949824] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.953981] scsi 10:0:15:0: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  259.959098] scsi 10:0:15:0: Notifying upper driver of completion (result 10000)
Jul 31 20:12:34 fslab1 kernel: [  259.966499] 0 sectors total, 36 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  259.970766] scsi scan: INQUIRY failed with code 0x10000
Jul 31 20:12:34 fslab1 kernel: [  259.976109] scsi 10:0:16:0: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:34 fslab1 kernel: [  259.982106] scsi 10:0:16:0: Send: 
Jul 31 20:12:34 fslab1 kernel: [  259.985575] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  259.988826] scsi 10:0:16:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  259.992204] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  259.996342] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  260.004354] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  260.008342] scsi 10:0:16:0: Done: 
Jul 31 20:12:34 fslab1 kernel: [  260.011802] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  260.015654] scsi 10:0:16:0:  
Jul 31 20:12:34 fslab1 kernel: [  260.018680] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  260.024056] scsi 10:0:16:0: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.027427] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  260.031580] scsi 10:0:16:0: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  260.036695] scsi 10:0:16:0: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  260.043725] 0 sectors total, 36 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  260.047990] scsi scan: INQUIRY successful with code 0x0
Jul 31 20:12:34 fslab1 kernel: [  260.053322] scsi 10:0:16:0: Processor         Areca    RAID controller  R001 PQ: 0 ANSI: 0
Jul 31 20:12:34 fslab1 kernel: [  260.061704] scsi scan: Sequential scan oftarget10:0:16
Jul 31 20:12:34 fslab1 kernel: [  260.066963] scsi 10:0:16:1: scsi scan: INQUIRY pass 1 length 36
Jul 31 20:12:34 fslab1 kernel: [  260.072991] scsi 10:0:16:1: Send: 
Jul 31 20:12:34 fslab1 kernel: [  260.076475] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  260.079715] scsi 10:0:16:1: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.083092] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  260.087239] buffer = 0xffff8800bebf4ec0, bufflen = 36, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  260.095254] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  260.099239] scsi 10:0:16:1: Done: 
Jul 31 20:12:34 fslab1 kernel: [  260.102703] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  260.106549] scsi 10:0:16:1:  
Jul 31 20:12:34 fslab1 kernel: [  260.109578] Result: hostbyte=DID_TIME_OUT driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  260.115474] scsi 10:0:16:1: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.118847] Inquiry: 12 00 00 00 24 00
Jul 31 20:12:34 fslab1 kernel: [  260.122996] scsi 10:0:16:1: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  260.128113] scsi 10:0:16:1: Notifying upper driver of completion (result 30000)
Jul 31 20:12:34 fslab1 kernel: [  260.135512] 0 sectors total, 36 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  260.139776] scsi scan: INQUIRY failed with code 0x30000
Jul 31 20:12:34 fslab1 kernel: [  260.145179] sd 10:0:1:5: sd_probe
Jul 31 20:12:34 fslab1 kernel: [  260.148626] sd 10:0:1:5: [sdb] sd_revalidate_disk
Jul 31 20:12:34 fslab1 kernel: [  260.153424] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  260.156646] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  260.159906] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.163026] Test Unit Ready: 00 00 00 00 00 00
Jul 31 20:12:34 fslab1 kernel: [  260.167951] buffer = 0x          (null), bufflen = 0, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  260.175877] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  260.179884] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  260.183087] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  260.186940] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  260.189706] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  260.195081] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.198195] Test Unit Ready: 00 00 00 00 00 00
Jul 31 20:12:34 fslab1 kernel: [  260.203039] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  260.207895] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  260.214663] 0 sectors total, 0 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  260.218863] sg_alloc: dev=1 
Jul 31 20:12:34 fslab1 kernel: [  260.221878] sd 10:0:1:5: Attached scsi generic sg1 type 0
Jul 31 20:12:34 fslab1 kernel: [  260.227355] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  260.230581] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  260.233833] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.236966] Read capacity(16): 9e 10 00 00 00 00 00 00 00 00 00 00 00 20 00 00
Jul 31 20:12:34 fslab1 kernel: [  260.245107] buffer = 0xffff8800bebf4ec0, bufflen = 32, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  260.253121] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  260.257239] sg_alloc: dev=2 
Jul 31 20:12:34 fslab1 kernel: [  260.260184] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  260.263382] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  260.267243] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  260.270009] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  260.275383] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.278497] Read capacity(16): 9e 10 00 00 00 00 00 00 00 00 00 00 00 20 00 00
Jul 31 20:12:34 fslab1 kernel: [  260.286585] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  260.291441] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  260.298208] 0 sectors total, 32 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  260.302468] sd 10:0:1:5: [sdb] 781422768 512-byte logical blocks: (400 GB/372 GiB)
Jul 31 20:12:34 fslab1 kernel: [  260.310179] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  260.313384] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  260.316665] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.319803] Inquiry: 12 01 00 00 40 00
Jul 31 20:12:34 fslab1 kernel: [  260.323960] buffer = 0xffff8800bebf4ec0, bufflen = 64, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  260.332000] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  260.336032] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  260.339230] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  260.343088] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  260.345856] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  260.351232] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.354344] Inquiry: 12 01 00 00 40 00
Jul 31 20:12:34 fslab1 kernel: [  260.358494] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  260.363351] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  260.370118] 0 sectors total, 64 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  260.374457] scsi 10:0:16:0: Attached scsi generic sg2 type 3
Jul 31 20:12:34 fslab1 kernel: [  260.380288] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  260.383523] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  260.386774] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.389922] Inquiry: 12 01 00 00 40 00
Jul 31 20:12:34 fslab1 kernel: [  260.394109] buffer = 0xffff8800bebf4ec0, bufflen = 64, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  260.402150] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  260.406172] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  260.409378] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  260.413237] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  260.416000] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  260.421380] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.424494] Inquiry: 12 01 00 00 40 00
Jul 31 20:12:34 fslab1 kernel: [  260.428642] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  260.433501] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  260.440267] 0 sectors total, 64 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  260.444526] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  260.447726] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  260.451007] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.454125] Mode Sense(6): 1a 00 3f 00 04 00
Jul 31 20:12:34 fslab1 kernel: [  260.458892] buffer = 0xffff8800bebf4ec0, bufflen = 4, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  260.466816] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  260.470814] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  260.474019] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  260.477865] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  260.480632] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  260.486008] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.489121] Mode Sense(6): 1a 00 3f 00 04 00
Jul 31 20:12:34 fslab1 kernel: [  260.493799] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  260.498656] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  260.505424] 0 sectors total, 4 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  260.509608] sd 10:0:1:5: [sdb] Write Protect is off
Jul 31 20:12:34 fslab1 kernel: [  260.514586] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  260.517789] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  260.521040] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.524155] Mode Sense(6): 1a 00 08 00 04 00
Jul 31 20:12:34 fslab1 kernel: [  260.528833] buffer = 0xffff8800bebf4ec0, bufflen = 4, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  260.536759] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  260.540756] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  260.543955] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  260.547807] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  260.550575] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  260.555948] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.559063] Mode Sense(6): 1a 00 08 00 04 00
Jul 31 20:12:34 fslab1 kernel: [  260.563733] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  260.568588] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  260.575357] 0 sectors total, 4 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  260.579539] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  260.582770] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  260.586022] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.589141] Mode Sense(6): 1a 00 08 00 20 00
Jul 31 20:12:34 fslab1 kernel: [  260.593807] buffer = 0xffff8800bebf4ec0, bufflen = 32, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  260.602706] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  260.606696] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  260.609896] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  260.613750] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  260.616517] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  260.621893] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.625008] Mode Sense(6): 1a 00 08 00 20 00
Jul 31 20:12:34 fslab1 kernel: [  260.629684] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  260.634541] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  260.641309] 0 sectors total, 32 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  260.645555] sd 10:0:1:5: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Jul 31 20:12:34 fslab1 kernel: [  260.654786] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  260.657990] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  260.661226] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.664342] Report supported operation codes: a3 0c 01 12 00 00 00 00 02 00 00 00
Jul 31 20:12:34 fslab1 kernel: [  260.672515] buffer = 0xffff8800bebf4ec0, bufflen = 512, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  260.680612] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  260.684608] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  260.687810] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  260.691668] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  260.694436] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  260.699810] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.702923] Report supported operation codes: a3 0c 01 12 00 00 00 00 02 00 00 00
Jul 31 20:12:34 fslab1 kernel: [  260.711099] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  260.715954] sd 10:0:1:5: Notifying upper driver of completion (result 8000000)
Jul 31 20:12:34 fslab1 kernel: [  260.723268] 1 sectors total, 512 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  260.727622] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  260.730855] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  260.734107] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.737225] Inquiry: 12 01 00 02 00 00
Jul 31 20:12:34 fslab1 kernel: [  260.741364] buffer = 0xffff8800bebf4ec0, bufflen = 512, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  260.749461] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  260.753453] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  260.756653] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  260.760506] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  260.763273] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  260.768650] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.771761] Inquiry: 12 01 00 02 00 00
Jul 31 20:12:34 fslab1 kernel: [  260.775907] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  260.780762] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  260.787530] 1 sectors total, 512 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  260.791950] sd 10:0:1:5: [sdb] sd_open
Jul 31 20:12:34 fslab1 kernel: [  260.795762] scsi_block_when_processing_errors: rtn: 1
Jul 31 20:12:34 fslab1 kernel: [  260.800900] sd 10:0:1:5: [sdb] sd_revalidate_disk
Jul 31 20:12:34 fslab1 kernel: [  260.805723] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  260.808952] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  260.812197] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.815311] Test Unit Ready: 00 00 00 00 00 00
Jul 31 20:12:34 fslab1 kernel: [  260.820173] buffer = 0x          (null), bufflen = 0, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  260.828101] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  260.832095] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  260.835297] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  260.839155] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  260.841924] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  260.847298] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.850413] Test Unit Ready: 00 00 00 00 00 00
Jul 31 20:12:34 fslab1 kernel: [  260.855257] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  260.860112] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  260.866881] 0 sectors total, 0 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  260.871065] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  260.874271] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  260.877520] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.880636] Read capacity(16): 9e 10 00 00 00 00 00 00 00 00 00 00 00 20 00 00
Jul 31 20:12:34 fslab1 kernel: [  260.888713] buffer = 0xffff8800bebf4ec0, bufflen = 32, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  260.896723] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  260.900716] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  260.903910] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  260.907753] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  260.910520] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  260.915896] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.919009] Read capacity(16): 9e 10 00 00 00 00 00 00 00 00 00 00 00 20 00 00
Jul 31 20:12:34 fslab1 kernel: [  260.927079] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  260.931934] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  260.938702] 0 sectors total, 32 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  260.942951] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  260.946159] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  260.949403] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.952518] Inquiry: 12 01 00 00 40 00
Jul 31 20:12:34 fslab1 kernel: [  260.956668] buffer = 0xffff8800bebf4ec0, bufflen = 64, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  260.964678] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  260.968671] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  260.971867] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  260.975719] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  260.978485] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  260.983861] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  260.986974] Inquiry: 12 01 00 00 40 00
Jul 31 20:12:34 fslab1 kernel: [  260.991125] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  260.995980] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  261.002748] 0 sectors total, 64 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  261.007002] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  261.010203] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  261.013448] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  261.016566] Inquiry: 12 01 00 00 40 00
Jul 31 20:12:34 fslab1 kernel: [  261.020705] buffer = 0xffff8800bebf4ec0, bufflen = 64, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  261.028716] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  261.032814] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  261.036017] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  261.039869] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  261.042637] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  261.048010] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  261.051121] Inquiry: 12 01 00 00 40 00
Jul 31 20:12:34 fslab1 kernel: [  261.055274] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  261.060131] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  261.066899] 0 sectors total, 64 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  261.071156] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  261.074385] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  261.077633] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  261.080752] Mode Sense(6): 1a 00 3f 00 04 00
Jul 31 20:12:34 fslab1 kernel: [  261.085429] buffer = 0xffff8800bebf4ec0, bufflen = 4, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  261.093352] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  261.097350] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  261.100553] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  261.104404] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  261.107163] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  261.112534] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  261.115645] Mode Sense(6): 1a 00 3f 00 04 00
Jul 31 20:12:34 fslab1 kernel: [  261.120318] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  261.125174] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  261.131942] 0 sectors total, 4 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  261.136135] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  261.139357] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  261.142607] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  261.145728] Mode Sense(6): 1a 00 08 00 04 00
Jul 31 20:12:34 fslab1 kernel: [  261.150401] buffer = 0xffff8800bebf4ec0, bufflen = 4, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  261.158325] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  261.162317] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  261.165517] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  261.169365] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  261.172132] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  261.177508] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  261.180620] Mode Sense(6): 1a 00 08 00 04 00
Jul 31 20:12:34 fslab1 kernel: [  261.185290] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  261.190147] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  261.196915] 0 sectors total, 4 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  261.201083] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  261.204283] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  261.207521] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  261.210637] Mode Sense(6): 1a 00 08 00 20 00
Jul 31 20:12:34 fslab1 kernel: [  261.215306] buffer = 0xffff8800bebf4ec0, bufflen = 32, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  261.223318] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  261.227309] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  261.230510] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  261.234356] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  261.237123] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  261.242497] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  261.245612] Mode Sense(6): 1a 00 08 00 20 00
Jul 31 20:12:34 fslab1 kernel: [  261.250283] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  261.255138] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  261.261906] 0 sectors total, 32 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  261.266161] sd 10:0:1:5: Send: 
Jul 31 20:12:34 fslab1 kernel: [  261.269373] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  261.272616] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  261.275728] Inquiry: 12 01 00 02 00 00
Jul 31 20:12:34 fslab1 kernel: [  261.279882] buffer = 0xffff8800bebf4ec0, bufflen = 512, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  261.287978] leaving scsi_dispatch_cmnd()
Jul 31 20:12:34 fslab1 kernel: [  261.291974] sd 10:0:1:5: Done: 
Jul 31 20:12:34 fslab1 kernel: [  261.295183] 0xffff88007feff180 SUCCESS
Jul 31 20:12:34 fslab1 kernel: [  261.299036] sd 10:0:1:5:  
Jul 31 20:12:34 fslab1 kernel: [  261.301802] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:12:34 fslab1 kernel: [  261.307178] sd 10:0:1:5: CDB: 
Jul 31 20:12:34 fslab1 kernel: [  261.310291] Inquiry: 12 01 00 02 00 00
Jul 31 20:12:34 fslab1 kernel: [  261.314442] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:12:34 fslab1 kernel: [  261.319297] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:12:34 fslab1 kernel: [  261.326942] 1 sectors total, 512 bytes done.
Jul 31 20:12:34 fslab1 kernel: [  261.331334] sd 10:0:1:5: [sdb] sd_prep_fn: block=0, count=8
Jul 31 20:12:34 fslab1 kernel: [  261.335274] sd 10:0:1:5: [sdb] block=0
Jul 31 20:12:34 fslab1 kernel: [  261.335274] sd 10:0:1:5: [sdb] reading 8/8 512 byte blocks.
Jul 31 20:12:34 fslab1 kernel: [  261.346421] sd 10:0:1:5: [sdb] Send: 
Jul 31 20:12:34 fslab1 kernel: [  261.350160] 0xffff88007feff180 
Jul 31 20:12:34 fslab1 kernel: [  261.353413] sd 10:0:1:5: [sdb] CDB: 
Jul 31 20:12:34 fslab1 kernel: [  261.357053] Read(10): 28 00 00 00 00 00 00 00 08 00
Jul 31 20:12:34 fslab1 kernel: [  261.362498] buffer = 0xffff8800bebf4ec0, bufflen = 4096, queuecommand 0xffffffffa029a350
Jul 31 20:12:34 fslab1 kernel: [  261.370683] leaving scsi_dispatch_cmnd()
Jul 31 20:13:04 fslab1 kernel: [  291.840015] sd 10:0:1:5: [sdb] Done: 
Jul 31 20:13:04 fslab1 kernel: [  291.843744] 0xffff88007feff180 TIMEOUT
Jul 31 20:13:04 fslab1 kernel: [  291.844005] sd 10:0:1:5: [sdb]  
Jul 31 20:13:04 fslab1 kernel: [  291.844005] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:13:04 fslab1 kernel: [  291.844005] sd 10:0:1:5: [sdb] CDB: 
Jul 31 20:13:04 fslab1 kernel: [  291.844005] Read(10): 28 00 00 00 00 00 00 00 08 00
Jul 31 20:13:04 fslab1 kernel: [  291.844005] sd 10:0:1:5: [sdb] scsi host busy 1 failed 0
Jul 31 20:13:04 fslab1 kernel: [  291.844005] Waking error handler thread
Jul 31 20:13:04 fslab1 kernel: [  291.874609] Error handler scsi_eh_10 waking up
Jul 31 20:13:04 fslab1 kernel: [  291.879339] sd 10:0:1:5: scsi_eh_prt_fail_stats: cmds failed: 0, cancel: 1
Jul 31 20:13:04 fslab1 kernel: [  291.886311] Total of 1 commands on 1 devices require eh work
Jul 31 20:13:04 fslab1 kernel: [  291.892039] scsi_eh_10: aborting cmd:0xffff88007feff180
Jul 31 20:13:04 fslab1 kernel: [  291.897356] arcmsr10: abort device command of scsi id = 1 lun = 5 
Jul 31 20:13:07 fslab1 kernel: [  295.132027] scsi_eh_10: aborting cmd failed:0xffff88007feff180
Jul 31 20:13:07 fslab1 kernel: [  295.137949] scsi_eh_10: Sending BDR sdev: 0xffff8800bebcf000
Jul 31 20:13:07 fslab1 kernel: [  295.143719] scsi_eh_10: BDR failed sdev:0xffff8800bebcf000
Jul 31 20:13:07 fslab1 kernel: [  295.149274] scsi_eh_10: Sending target reset to target 1
Jul 31 20:13:07 fslab1 kernel: [  295.154654] scsi_eh_10: Target reset failed target: 1
Jul 31 20:13:07 fslab1 kernel: [  295.159768] scsi_eh_10: Sending BRST chan: 0
Jul 31 20:13:07 fslab1 kernel: [  295.164100] scsi_try_bus_reset: Snd Bus RST
Jul 31 20:13:07 fslab1 kernel: [  295.168350] arcmsr: executing bus reset eh.....num_resets = 0, num_aborts = 1 
Jul 31 20:13:39 fslab1 kernel: [  327.172022] arcmsr10: wait 'abort all outstanding command' timeout 
Jul 31 20:13:39 fslab1 kernel: [  327.178383] arcmsr10: executing hw bus reset .....
Jul 31 20:13:52 fslab1 kernel: [  340.192020] arcmsr10: waiting for hw bus reset return, retry=0
Jul 31 20:14:02 fslab1 kernel: [  350.200023] arcmsr10: waiting for hw bus reset return, retry=1
Jul 31 20:14:12 fslab1 kernel: [  360.208022] arcmsr10: waiting for hw bus reset return, retry=2
Jul 31 20:14:22 fslab1 kernel: [  370.216022] arcmsr10: waiting for hw bus reset return, retry=3
Jul 31 20:14:32 fslab1 kernel: [  380.240050] Areca RAID Controller10: F/W V1.46 2009-01-06 & Model ARC-1260
Jul 31 20:14:32 fslab1 kernel: [  380.260013] arcmsr: scsi  bus reset eh returns with success
Jul 31 20:14:42 fslab1 kernel: [  390.268027] sd 10:0:1:5: [sdb] Send: 
Jul 31 20:14:42 fslab1 kernel: [  390.271757] 0xffff88007feff180 
Jul 31 20:14:43 fslab1 kernel: [  390.275016] sd 10:0:1:5: [sdb] CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.278657] Test Unit Ready: 00 00 00 00 00 00
Jul 31 20:14:43 fslab1 kernel: [  390.278659] buffer = 0x          (null), bufflen = 0, queuecommand 0xffffffffa029a350
Jul 31 20:14:43 fslab1 kernel: [  390.283177] scsi_eh_done scmd: ffff88007feff180 result: 0
Jul 31 20:14:43 fslab1 kernel: [  390.283189] sd 10:0:1:5: [sdb] Done: 
Jul 31 20:14:43 fslab1 kernel: [  390.283191] 0xffff88007feff180 UNKNOWN
Jul 31 20:14:43 fslab1 kernel: [  390.283192] sd 10:0:1:5: [sdb]  
Jul 31 20:14:43 fslab1 kernel: [  390.283193] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:14:43 fslab1 kernel: [  390.283195] sd 10:0:1:5: [sdb] CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.283198] Test Unit Ready: 00 00 00 00 00 00
Jul 31 20:14:43 fslab1 kernel: [  390.283199] sd 10:0:1:5: [sdb] scsi host busy 1 failed 1
Jul 31 20:14:43 fslab1 kernel: [  390.283201] scsi_send_eh_cmnd: scmd: ffff88007feff180, timeleft: 2499
Jul 31 20:14:43 fslab1 kernel: [  390.283202] scsi_send_eh_cmnd: scsi_eh_completed_normally 2002
Jul 31 20:14:43 fslab1 kernel: [  390.283204] scsi_eh_tur: scmd ffff88007feff180 rtn 2002
Jul 31 20:14:43 fslab1 kernel: [  390.283205] scsi_eh_10: flush retry cmd: ffff88007feff180
Jul 31 20:14:43 fslab1 kernel: [  390.283207] Inserting command ffff88007feff180 into mlqueue
Jul 31 20:14:43 fslab1 kernel: [  390.283217] scsi_restart_operations: waking up host to restart
Jul 31 20:14:43 fslab1 kernel: [  390.283229] Error handler scsi_eh_10 sleeping
Jul 31 20:14:43 fslab1 kernel: [  390.292011] sd 10:0:1:5: unblocking device at zero depth
Jul 31 20:14:43 fslab1 kernel: [  390.292015] sd 10:0:1:5: [sdb] Send: 
Jul 31 20:14:43 fslab1 kernel: [  390.292016] 0xffff88007feff180 
Jul 31 20:14:43 fslab1 kernel: [  390.292017] sd 10:0:1:5: [sdb] CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.292022] Read(10): 28 00 00 00 00 00 00 00 08 00
Jul 31 20:14:43 fslab1 kernel: [  390.292023] buffer = 0xffff8800bebf4ec0, bufflen = 4096, queuecommand 0xffffffffa029a350
Jul 31 20:14:43 fslab1 kernel: [  390.292026] leaving scsi_dispatch_cmnd()
Jul 31 20:14:43 fslab1 kernel: [  390.296576] sd 10:0:1:5: [sdb] Done: 
Jul 31 20:14:43 fslab1 kernel: [  390.296578] 0xffff88007feff180 SUCCESS
Jul 31 20:14:43 fslab1 kernel: [  390.296580] sd 10:0:1:5: [sdb]  
Jul 31 20:14:43 fslab1 kernel: [  390.296581] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:14:43 fslab1 kernel: [  390.296583] sd 10:0:1:5: [sdb] CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.296588] Read(10): 28 00 00 00 00 00 00 00 08 00
Jul 31 20:14:43 fslab1 kernel: [  390.296590] sd 10:0:1:5: [sdb] scsi host busy 1 failed 0
Jul 31 20:14:43 fslab1 kernel: [  390.296593] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:14:43 fslab1 kernel: [  390.296594] sd 10:0:1:5: [sdb]  
Jul 31 20:14:43 fslab1 kernel: [  390.296595] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:14:43 fslab1 kernel: [  390.296597] 8 sectors total, 4096 bytes done.
Jul 31 20:14:43 fslab1 kernel: [  390.448438]  sdb: sdb1
Jul 31 20:14:43 fslab1 kernel: [  390.451006] sd 10:0:1:5: [sdb] sd_release
Jul 31 20:14:43 fslab1 kernel: [  390.455305] sd 10:0:1:5: [sdb] sd_revalidate_disk
Jul 31 20:14:43 fslab1 kernel: [  390.460083] sd 10:0:1:5: [sdb] sd_check_events
Jul 31 20:14:43 fslab1 kernel: [  390.464624] scsi_block_when_processing_errors: rtn: 1
Jul 31 20:14:43 fslab1 kernel: [  390.469781] sd 10:0:1:5: Send: 
Jul 31 20:14:43 fslab1 kernel: [  390.473004] 0xffff88007feff180 
Jul 31 20:14:43 fslab1 kernel: [  390.476249] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.479362] Test Unit Ready: 00 00 00 00 00 00
Jul 31 20:14:43 fslab1 kernel: [  390.484273] buffer = 0x          (null), bufflen = 0, queuecommand 0xffffffffa029a350
Jul 31 20:14:43 fslab1 kernel: [  390.492210] leaving scsi_dispatch_cmnd()
Jul 31 20:14:43 fslab1 kernel: [  390.496224] sd 10:0:1:5: Done: 
Jul 31 20:14:43 fslab1 kernel: [  390.499426] 0xffff88007feff180 SUCCESS
Jul 31 20:14:43 fslab1 kernel: [  390.503278] sd 10:0:1:5:  
Jul 31 20:14:43 fslab1 kernel: [  390.506042] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:14:43 fslab1 kernel: [  390.511415] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.514526] Test Unit Ready: 00 00 00 00 00 00
Jul 31 20:14:43 fslab1 kernel: [  390.519369] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:14:43 fslab1 kernel: [  390.524222] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:14:43 fslab1 kernel: [  390.530986] 0 sectors total, 0 bytes done.
Jul 31 20:14:43 fslab1 kernel: [  390.535159] sd 10:0:1:5: Send: 
Jul 31 20:14:43 fslab1 kernel: [  390.538380] 0xffff88007feff180 
Jul 31 20:14:43 fslab1 kernel: [  390.541626] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.544760] Read capacity(16): 9e 10 00 00 00 00 00 00 00 00 00 00 00 20 00 00
Jul 31 20:14:43 fslab1 kernel: [  390.552920] buffer = 0xffff8800bebf4ec0, bufflen = 32, queuecommand 0xffffffffa029a350
Jul 31 20:14:43 fslab1 kernel: [  390.560928] leaving scsi_dispatch_cmnd()
Jul 31 20:14:43 fslab1 kernel: [  390.564937] sd 10:0:1:5: Send: 
Jul 31 20:14:43 fslab1 kernel: [  390.568142] sd 10:0:1:5: Done: 
Jul 31 20:14:43 fslab1 kernel: [  390.571341] 0xffff88007feff180 SUCCESS
Jul 31 20:14:43 fslab1 kernel: [  390.575196] sd 10:0:1:5:  
Jul 31 20:14:43 fslab1 kernel: [  390.577962] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:14:43 fslab1 kernel: [  390.583334] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.586446] Read capacity(16): 9e 10 00 00 00 00 00 00 00 00 00 00 00 20 00 00
Jul 31 20:14:43 fslab1 kernel: [  390.594521] sd 10:0:1:5: scsi host busy 2 failed 0
Jul 31 20:14:43 fslab1 kernel: [  390.599374] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:14:43 fslab1 kernel: [  390.606136] 0 sectors total, 32 bytes done.
Jul 31 20:14:43 fslab1 kernel: [  390.610388] 0xffff88007feff480 
Jul 31 20:14:43 fslab1 kernel: [  390.613651] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.616769] Test Unit Ready: 00 00 00 00 00 00
Jul 31 20:14:43 fslab1 kernel: [  390.621631] buffer = 0x          (null), bufflen = 0, queuecommand 0xffffffffa029a350
Jul 31 20:14:43 fslab1 kernel: [  390.629551] leaving scsi_dispatch_cmnd()
Jul 31 20:14:43 fslab1 kernel: [  390.633587] sd 10:0:1:5: Done: 
Jul 31 20:14:43 fslab1 kernel: [  390.636792] 0xffff88007feff480 SUCCESS
Jul 31 20:14:43 fslab1 kernel: [  390.640641] sd 10:0:1:5:  
Jul 31 20:14:43 fslab1 kernel: [  390.643407] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:14:43 fslab1 kernel: [  390.648781] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.651891] Test Unit Ready: 00 00 00 00 00 00
Jul 31 20:14:43 fslab1 kernel: [  390.656742] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:14:43 fslab1 kernel: [  390.661595] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:14:43 fslab1 kernel: [  390.668361] 0 sectors total, 0 bytes done.
Jul 31 20:14:43 fslab1 kernel: [  390.672525] sd 10:0:1:5: Send: 
Jul 31 20:14:43 fslab1 kernel: [  390.675721] 0xffff88007feff480 
Jul 31 20:14:43 fslab1 kernel: [  390.678981] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.682093] Inquiry: 12 01 00 00 40 00
Jul 31 20:14:43 fslab1 kernel: [  390.686239] buffer = 0xffff8800bebf4ec0, bufflen = 64, queuecommand 0xffffffffa029a350
Jul 31 20:14:43 fslab1 kernel: [  390.694244] leaving scsi_dispatch_cmnd()
Jul 31 20:14:43 fslab1 kernel: [  390.698245] sd 10:0:1:5: Done: 
Jul 31 20:14:43 fslab1 kernel: [  390.701450] 0xffff88007feff480 SUCCESS
Jul 31 20:14:43 fslab1 kernel: [  390.705294] sd 10:0:1:5:  
Jul 31 20:14:43 fslab1 kernel: [  390.708061] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:14:43 fslab1 kernel: [  390.713431] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.716543] Inquiry: 12 01 00 00 40 00
Jul 31 20:14:43 fslab1 kernel: [  390.720690] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:14:43 fslab1 kernel: [  390.725543] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:14:43 fslab1 kernel: [  390.732308] 0 sectors total, 64 bytes done.
Jul 31 20:14:43 fslab1 kernel: [  390.736565] sd 10:0:1:5: Send: 
Jul 31 20:14:43 fslab1 kernel: [  390.739764] 0xffff88007feff480 
Jul 31 20:14:43 fslab1 kernel: [  390.743011] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.746126] Inquiry: 12 01 00 00 40 00
Jul 31 20:14:43 fslab1 kernel: [  390.750272] buffer = 0xffff8800bebf4ec0, bufflen = 64, queuecommand 0xffffffffa029a350
Jul 31 20:14:43 fslab1 kernel: [  390.758278] leaving scsi_dispatch_cmnd()
Jul 31 20:14:43 fslab1 kernel: [  390.762276] sd 10:0:1:5: Done: 
Jul 31 20:14:43 fslab1 kernel: [  390.762290] sd 10:0:1:5: [sdb] sd_open
Jul 31 20:14:43 fslab1 kernel: [  390.762293] scsi_block_when_processing_errors: rtn: 1
Jul 31 20:14:43 fslab1 kernel: [  390.762308] sd 10:0:1:5: [sdb] sd_ioctl: disk=sdb, cmd=0x2285
Jul 31 20:14:43 fslab1 kernel: [  390.762310] scsi_block_when_processing_errors: rtn: 1
Jul 31 20:14:43 fslab1 kernel: [  390.762313] sd 10:0:1:5: [sdb] sd_ioctl: disk=sdb, cmd=0x2285
Jul 31 20:14:43 fslab1 kernel: [  390.762314] scsi_block_when_processing_errors: rtn: 1
Jul 31 20:14:43 fslab1 kernel: [  390.762354] sd 10:0:1:5: [sdb] Send: 
Jul 31 20:14:43 fslab1 kernel: [  390.762355] 0xffff8801f9aa8ec0 
Jul 31 20:14:43 fslab1 kernel: [  390.762357] sd 10:0:1:5: [sdb] CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.762360] Inquiry: 12 00 00 00 fe 00
Jul 31 20:14:43 fslab1 kernel: [  390.762362] buffer = 0xffff8801f94e1980, bufflen = 254, queuecommand 0xffffffffa029a350
Jul 31 20:14:43 fslab1 kernel: [  390.762366] leaving scsi_dispatch_cmnd()
Jul 31 20:14:43 fslab1 kernel: [  390.822613] 0xffff88007feff480 SUCCESS
Jul 31 20:14:43 fslab1 kernel: [  390.826458] sd 10:0:1:5:  
Jul 31 20:14:43 fslab1 kernel: [  390.829221] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:14:43 fslab1 kernel: [  390.834594] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.837706] Inquiry: 12 01 00 00 40 00
Jul 31 20:14:43 fslab1 kernel: [  390.841845] sd 10:0:1:5: scsi host busy 2 failed 0
Jul 31 20:14:43 fslab1 kernel: [  390.846697] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:14:43 fslab1 kernel: [  390.854338] 0 sectors total, 64 bytes done.
Jul 31 20:14:43 fslab1 kernel: [  390.858594] sd 10:0:1:5: [sdb] Done: 
Jul 31 20:14:43 fslab1 kernel: [  390.862315] 0xffff8801f9aa8ec0 SUCCESS
Jul 31 20:14:43 fslab1 kernel: [  390.866160] sd 10:0:1:5: [sdb]  
Jul 31 20:14:43 fslab1 kernel: [  390.869446] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:14:43 fslab1 kernel: [  390.874817] sd 10:0:1:5: [sdb] CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.878449] Inquiry: 12 00 00 00 fe 00
Jul 31 20:14:43 fslab1 kernel: [  390.882598] sd 10:0:1:5: [sdb] scsi host busy 1 failed 0
Jul 31 20:14:43 fslab1 kernel: [  390.887972] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:14:43 fslab1 kernel: [  390.894733] 0 sectors total, 254 bytes done.
Jul 31 20:14:43 fslab1 kernel: [  390.899095] sd 10:0:1:5: [sdb] sd_check_events
Jul 31 20:14:43 fslab1 kernel: [  390.899108] sd 10:0:1:5: Send: 
Jul 31 20:14:43 fslab1 kernel: [  390.899109] 0xffff88007feff480 
Jul 31 20:14:43 fslab1 kernel: [  390.899111] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.899114] Mode Sense(6): 1a 00 3f 00 04 00
Jul 31 20:14:43 fslab1 kernel: [  390.899115] buffer = 0xffff8800bebf4ec0, bufflen = 4, queuecommand 0xffffffffa029a350
Jul 31 20:14:43 fslab1 kernel: [  390.899116] leaving scsi_dispatch_cmnd()
Jul 31 20:14:43 fslab1 kernel: [  390.899141] sd 10:0:1:5: Done: 
Jul 31 20:14:43 fslab1 kernel: [  390.899142] 0xffff88007feff480 SUCCESS
Jul 31 20:14:43 fslab1 kernel: [  390.899143] sd 10:0:1:5:  
Jul 31 20:14:43 fslab1 kernel: [  390.899144] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:14:43 fslab1 kernel: [  390.899145] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.899148] Mode Sense(6): 1a 00 3f 00 04 00
Jul 31 20:14:43 fslab1 kernel: [  390.899149] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:14:43 fslab1 kernel: [  390.899151] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:14:43 fslab1 kernel: [  390.899151] 0 sectors total, 4 bytes done.
Jul 31 20:14:43 fslab1 kernel: [  390.899163] sd 10:0:1:5: Send: 
Jul 31 20:14:43 fslab1 kernel: [  390.899164] 0xffff88007feff480 
Jul 31 20:14:43 fslab1 kernel: [  390.899165] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.899168] Mode Sense(6): 1a 00 08 00 04 00
Jul 31 20:14:43 fslab1 kernel: [  390.899169] buffer = 0xffff8800bebf4ec0, bufflen = 4, queuecommand 0xffffffffa029a350
Jul 31 20:14:43 fslab1 kernel: [  390.899170] leaving scsi_dispatch_cmnd()
Jul 31 20:14:43 fslab1 kernel: [  390.899189] sd 10:0:1:5: Done: 
Jul 31 20:14:43 fslab1 kernel: [  390.899190] 0xffff88007feff480 SUCCESS
Jul 31 20:14:43 fslab1 kernel: [  390.899191] sd 10:0:1:5:  
Jul 31 20:14:43 fslab1 kernel: [  390.899192] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:14:43 fslab1 kernel: [  390.899193] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.899195] Mode Sense(6): 1a 00 08 00 04 00
Jul 31 20:14:43 fslab1 kernel: [  390.899197] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:14:43 fslab1 kernel: [  390.899199] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:14:43 fslab1 kernel: [  390.899199] 0 sectors total, 4 bytes done.
Jul 31 20:14:43 fslab1 kernel: [  390.899210] sd 10:0:1:5: Send: 
Jul 31 20:14:43 fslab1 kernel: [  390.899210] 0xffff88007feff480 
Jul 31 20:14:43 fslab1 kernel: [  390.899212] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.899214] Mode Sense(6): 1a 00 08 00 20 00
Jul 31 20:14:43 fslab1 kernel: [  390.899215] buffer = 0xffff8800bebf4ec0, bufflen = 32, queuecommand 0xffffffffa029a350
Jul 31 20:14:43 fslab1 kernel: [  390.899216] leaving scsi_dispatch_cmnd()
Jul 31 20:14:43 fslab1 kernel: [  390.899235] sd 10:0:1:5: Done: 
Jul 31 20:14:43 fslab1 kernel: [  390.899236] 0xffff88007feff480 SUCCESS
Jul 31 20:14:43 fslab1 kernel: [  390.899237] sd 10:0:1:5:  
Jul 31 20:14:43 fslab1 kernel: [  390.899238] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:14:43 fslab1 kernel: [  390.899239] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.899242] Mode Sense(6): 1a 00 08 00 20 00
Jul 31 20:14:43 fslab1 kernel: [  390.899243] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:14:43 fslab1 kernel: [  390.899244] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:14:43 fslab1 kernel: [  390.899245] 0 sectors total, 32 bytes done.
Jul 31 20:14:43 fslab1 kernel: [  390.899256] sd 10:0:1:5: Send: 
Jul 31 20:14:43 fslab1 kernel: [  390.899257] 0xffff88007feff480 
Jul 31 20:14:43 fslab1 kernel: [  390.899258] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.899261] Inquiry: 12 01 00 02 00 00
Jul 31 20:14:43 fslab1 kernel: [  390.899262] buffer = 0xffff8800bebf4ec0, bufflen = 512, queuecommand 0xffffffffa029a350
Jul 31 20:14:43 fslab1 kernel: [  390.899263] leaving scsi_dispatch_cmnd()
Jul 31 20:14:43 fslab1 kernel: [  390.899292] sd 10:0:1:5: Done: 
Jul 31 20:14:43 fslab1 kernel: [  390.899293] 0xffff88007feff480 SUCCESS
Jul 31 20:14:43 fslab1 kernel: [  390.899294] sd 10:0:1:5:  
Jul 31 20:14:43 fslab1 kernel: [  390.899295] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:14:43 fslab1 kernel: [  390.899296] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  390.899299] Inquiry: 12 01 00 02 00 00
Jul 31 20:14:43 fslab1 kernel: [  390.899300] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:14:43 fslab1 kernel: [  390.899302] sd 10:0:1:5: Notifying upper driver of completion (result 0)
Jul 31 20:14:43 fslab1 kernel: [  390.899302] 1 sectors total, 512 bytes done.
Jul 31 20:14:43 fslab1 kernel: [  390.899311] sd 10:0:1:5: [sdb] Attached SCSI disk
Jul 31 20:14:43 fslab1 kernel: [  391.164008] scsi_block_when_processing_errors: rtn: 1
Jul 31 20:14:43 fslab1 kernel: [  391.169231] sd 10:0:1:5: [sdb] sd_release
Jul 31 20:14:43 fslab1 kernel: [  391.173321] sd 10:0:1:5: Send: 
Jul 31 20:14:43 fslab1 kernel: [  391.176534] 0xffff8801f9aa8dc0 
Jul 31 20:14:43 fslab1 kernel: [  391.179784] sd 10:0:1:5: CDB: 
Jul 31 20:14:43 fslab1 kernel: [  391.182900] Test Unit Ready: 00 00 00 00 00 00
Jul 31 20:14:43 fslab1 kernel: [  391.187770] buffer = 0x          (null), bufflen = 0, queuecommand 0xffffffffa029a350
Jul 31 20:14:43 fslab1 kernel: [  391.195696] leaving scsi_dispatch_cmnd()
Jul 31 20:15:14 fslab1 kernel: [  421.856014] sd 10:0:1:5: Done: 
Jul 31 20:15:14 fslab1 kernel: [  421.859227] 0xffff8801f9aa8dc0 TIMEOUT
Jul 31 20:15:14 fslab1 kernel: [  421.860002] sd 10:0:1:5:  
Jul 31 20:15:14 fslab1 kernel: [  421.860002] Result: hostbyte=DID_OK driverbyte=DRIVER_OK
Jul 31 20:15:14 fslab1 kernel: [  421.860002] sd 10:0:1:5: CDB: 
Jul 31 20:15:14 fslab1 kernel: [  421.860002] Test Unit Ready: 00 00 00 00 00 00
Jul 31 20:15:14 fslab1 kernel: [  421.860002] sd 10:0:1:5: scsi host busy 1 failed 0
Jul 31 20:15:14 fslab1 kernel: [  421.860002] Waking error handler thread
Jul 31 20:15:14 fslab1 kernel: [  421.887932] Error handler scsi_eh_10 waking up
Jul 31 20:15:14 fslab1 kernel: [  421.892573] sd 10:0:1:5: scsi_eh_prt_fail_stats: cmds failed: 0, cancel: 1
Jul 31 20:15:14 fslab1 kernel: [  421.899523] Total of 1 commands on 1 devices require eh work
Jul 31 20:15:14 fslab1 kernel: [  421.905251] scsi_eh_10: aborting cmd:0xffff8801f9aa8dc0
Jul 31 20:15:14 fslab1 kernel: [  421.910542] arcmsr10: abort device command of scsi id = 1 lun = 5 
Jul 31 20:15:17 fslab1 kernel: [  425.148016] scsi_eh_10: aborting cmd failed:0xffff8801f9aa8dc0
Jul 31 20:15:17 fslab1 kernel: [  425.153933] scsi_eh_10: Sending BDR sdev: 0xffff8800bebcf000
Jul 31 20:15:17 fslab1 kernel: [  425.159665] scsi_eh_10: BDR failed sdev:0xffff8800bebcf000
Jul 31 20:15:17 fslab1 kernel: [  425.159667] scsi_eh_10: Sending target reset to target 1
Jul 31 20:15:17 fslab1 kernel: [  425.159668] scsi_eh_10: Target reset failed target: 1
Jul 31 20:15:17 fslab1 kernel: [  425.159669] scsi_eh_10: Sending BRST chan: 0
Jul 31 20:15:17 fslab1 kernel: [  425.159670] scsi_try_bus_reset: Snd Bus RST
Jul 31 20:15:17 fslab1 kernel: [  425.159672] arcmsr: executing bus reset eh.....num_resets = 1, num_aborts = 2 
Jul 31 20:15:49 fslab1 kernel: [  457.164014] arcmsr10: wait 'abort all outstanding command' timeout 

[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]