This is an automatic generated email to let you know that the following patch were queued:
Subject: [media] v4l: tvp5150: Fix comment regarding output pin muxing
Author: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
Date: Fri Dec 9 09:47:18 2016 -0200
The FID/GLCO/VLK/HVLK and INTREQ/GPCL/VBLK pins are muxed differently
depending on whether the input is an S-Video or composite signal. The
comment that explains the logic doesn't reflect the code. It appears
that the comment is incorrect, as disabling the output data bus in
composite mode makes no sense. Update the comment to match the code.
While at it define macros for the MISC_CTL register bits, the code is
too confusing with numerical values.
Cc: stable@xxxxxxxxxxxxxxx # For Kernel 4.5 and upper
Signed-off-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
Signed-off-by: Mauro Carvalho Chehab <mchehab@xxxxxxxxxxxxxxxx>
drivers/media/i2c/tvp5150.c | 24 +++++++++++++++++-------
drivers/media/i2c/tvp5150_reg.h | 9 +++++++++
2 files changed, 26 insertions(+), 7 deletions(-)
---
diff --git a/drivers/media/i2c/tvp5150.c b/drivers/media/i2c/tvp5150.c
index a30bfcb4eec6..8852fa8c957b 100644
--- a/drivers/media/i2c/tvp5150.c
+++ b/drivers/media/i2c/tvp5150.c
@@ -291,8 +291,12 @@ static void tvp5150_selmux(struct v4l2_subdev *sd)
tvp5150_write(sd, TVP5150_OP_MODE_CTL, opmode);
tvp5150_write(sd, TVP5150_VD_IN_SRC_SEL_1, input);
- /* Svideo should enable YCrCb output and disable GPCL output
- * For Composite and TV, it should be the reverse
+ /*
+ * Setup the FID/GLCO/VLK/HVLK and INTREQ/GPCL/VBLK output signals. For
+ * S-Video we output the vertical lock (VLK) signal on FID/GLCO/VLK/HVLK
+ * and set INTREQ/GPCL/VBLK to logic 0. For composite we output the
+ * field indicator (FID) signal on FID/GLCO/VLK/HVLK and set
+ * INTREQ/GPCL/VBLK to logic 1.
*/
val = tvp5150_read(sd, TVP5150_MISC_CTL);
if (val < 0) {
@@ -301,9 +305,9 @@ static void tvp5150_selmux(struct v4l2_subdev *sd)
}
if (decoder->input == TVP5150_SVIDEO)
- val = (val & ~0x40) | 0x10;
+ val = (val & ~TVP5150_MISC_CTL_GPCL) | TVP5150_MISC_CTL_HVLK;
else
- val = (val & ~0x10) | 0x40;
+ val = (val & ~TVP5150_MISC_CTL_HVLK) | TVP5150_MISC_CTL_GPCL;
tvp5150_write(sd, TVP5150_MISC_CTL, val);
};
@@ -455,7 +459,12 @@ static const struct i2c_reg_value tvp5150_init_enable[] = {
},{ /* Automatic offset and AGC enabled */
TVP5150_ANAL_CHL_CTL, 0x15
},{ /* Activate YCrCb output 0x9 or 0xd ? */
- TVP5150_MISC_CTL, 0x6f
+ TVP5150_MISC_CTL, TVP5150_MISC_CTL_GPCL |
+ TVP5150_MISC_CTL_INTREQ_OE |
+ TVP5150_MISC_CTL_YCBCR_OE |
+ TVP5150_MISC_CTL_SYNC_OE |
+ TVP5150_MISC_CTL_VBLANK |
+ TVP5150_MISC_CTL_CLOCK_OE,
},{ /* Activates video std autodetection for all standards */
TVP5150_AUTOSW_MSK, 0x0
},{ /* Default format: 0x47. For 4:2:2: 0x40 */
@@ -1050,11 +1059,12 @@ static int tvp5150_s_stream(struct v4l2_subdev *sd, int enable)
{
struct tvp5150 *decoder = to_tvp5150(sd);
/* Output format: 8-bit ITU-R BT.656 with embedded syncs */
- int val = 0x09;
+ int val = TVP5150_MISC_CTL_YCBCR_OE | TVP5150_MISC_CTL_CLOCK_OE;
/* Output format: 8-bit 4:2:2 YUV with discrete sync */
if (decoder->mbus_type == V4L2_MBUS_PARALLEL)
- val = 0x0d;
+ val = TVP5150_MISC_CTL_YCBCR_OE | TVP5150_MISC_CTL_SYNC_OE
+ | TVP5150_MISC_CTL_CLOCK_OE;
/* Initializes TVP5150 to its default values */
/* # set PCLK (27MHz) */
diff --git a/drivers/media/i2c/tvp5150_reg.h b/drivers/media/i2c/tvp5150_reg.h
index 25a994944918..30a48c28d05a 100644
--- a/drivers/media/i2c/tvp5150_reg.h
+++ b/drivers/media/i2c/tvp5150_reg.h
@@ -9,6 +9,15 @@
#define TVP5150_ANAL_CHL_CTL 0x01 /* Analog channel controls */
#define TVP5150_OP_MODE_CTL 0x02 /* Operation mode controls */
#define TVP5150_MISC_CTL 0x03 /* Miscellaneous controls */
+#define TVP5150_MISC_CTL_VBLK_GPCL BIT(7)
+#define TVP5150_MISC_CTL_GPCL BIT(6)
+#define TVP5150_MISC_CTL_INTREQ_OE BIT(5)
+#define TVP5150_MISC_CTL_HVLK BIT(4)
+#define TVP5150_MISC_CTL_YCBCR_OE BIT(3)
+#define TVP5150_MISC_CTL_SYNC_OE BIT(2)
+#define TVP5150_MISC_CTL_VBLANK BIT(1)
+#define TVP5150_MISC_CTL_CLOCK_OE BIT(0)
+
#define TVP5150_AUTOSW_MSK 0x04 /* Autoswitch mask: TVP5150A / TVP5150AM */
/* Reserved 05h */
--
To unsubscribe from this list: send the line "unsubscribe stable" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html