The DTSI file for the Nomadik does not properly specify how the
PL180 levelshifter is connected: the Nomadik actually needs all
the five st,sig-dir-* flags set to properly control all lines out.
Further this board supports full power cycling of the card, and
since this variant has no hardware clock gating, it needs a
ridiculously low frequency setting to keep up with the ever
overflowing FIFO.
The pin configuration set-up is a bit of a mystery, because of
course these pins are a mix of inputs and outputs. However the
reference implementation sets all pins to "output" with
unspecified initial value, so let's do that here as well.
Cc: stable@xxxxxxxxxxxxxxx
Cc: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
ARM SoC folks: this fixes the non-working SD/MMC card on the
Nomadik please apply this directly for fixes if Ulf is OK with
it.
---
arch/arm/boot/dts/ste-nomadik-stn8815.dtsi | 37 ++++++++++++++++--------------
1 file changed, 20 insertions(+), 17 deletions(-)
diff --git a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
index 50c256f0fd98..b1707f6217bf 100644
--- a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
@@ -128,22 +128,14 @@
};
mmcsd_default_mode: mmcsd_default {
mmcsd_default_cfg1 {
- /* MCCLK */
- pins = "GPIO8_B10";
- ste,output = <0>;
- };
- mmcsd_default_cfg2 {
- /* MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2 */
- pins = "GPIO10_C11", "GPIO15_A12",
- "GPIO16_C13", "GPIO23_D15";
- ste,output = <1>;
- };
- mmcsd_default_cfg3 {
- /* MCCMD, MCDAT3-0, MCMSFBCLK */
- pins = "GPIO9_A10", "GPIO11_B11",
- "GPIO12_A11", "GPIO13_C12",
- "GPIO14_B12", "GPIO24_C15";
- ste,input = <1>;
+ /*
+ * MCCLK, MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2
+ * MCCMD, MCDAT3-0, MCMSFBCLK
+ */
+ pins = "GPIO8_B10", "GPIO9_A10", "GPIO10_C11", "GPIO11_B11",
+ "GPIO12_A11", "GPIO13_C12", "GPIO14_B12", "GPIO15_A12",
+ "GPIO16_C13", "GPIO23_D15", "GPIO24_C15";
+ ste,output = <2>;
};
};
};
@@ -803,10 +795,21 @@
clock-names = "mclk", "apb_pclk";
interrupt-parent = <&vica>;
interrupts = <22>;
- max-frequency = <48000000>;
+ max-frequency = <400000>;
bus-width = <4>;
cap-mmc-highspeed;
cap-sd-highspeed;
+ full-pwr-cycle;
+ /*
+ * The STw4811 circuit used with the Nomadik strictly
+ * requires that all of these signal direction pins be
+ * routed and used for its 4-bit levelshifter.
+ */
+ st,sig-dir-dat0;
+ st,sig-dir-dat2;
+ st,sig-dir-dat31;
+ st,sig-dir-cmd;
+ st,sig-pin-fbclk;
pinctrl-names = "default";
pinctrl-0 = <&mmcsd_default_mux>, <&mmcsd_default_mode>;
vmmc-supply = <&vmmc_regulator>;
--
2.4.3
--
To unsubscribe from this list: send the line "unsubscribe stable" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html