This is a note to let you know that I've just added the patch titled
arm64: dts: rockchip: Fix reset-gpios property on brcm BT nodes
to the 6.6-stable tree which can be found at:
http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary
The filename of the patch is:
arm64-dts-rockchip-fix-reset-gpios-property-on-brcm-.patch
and it can be found in the queue-6.6 subdirectory.
If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@xxxxxxxxxxxxxxx> know about it.
commit 8b29c8df5f890c44c9a59f461e9b1e7d7d36d122
Author: Diederik de Haas <didi.debian@xxxxxxxxx>
Date: Tue Oct 8 13:15:39 2024 +0200
arm64: dts: rockchip: Fix reset-gpios property on brcm BT nodes
[ Upstream commit 2b6a3f857550e52b1cd4872ebb13cb3e3cf12f5f ]
For most compatibles, the "brcm,bluetooth.yaml" binding doesn't allow
the 'reset-gpios' property, but there is a 'shutdown-gpios' property.
Page 12 of the AzureWave-CM256SM datasheet (v1.9) has the following wrt
pin 34 'BT_REG_ON' (connected to GPIO0_C4_d on the PineNote):
Used by PMU to power up or power down the internal regulators used
by the Bluetooth section. Also, when deasserted, this pin holds the
Bluetooth section in reset. This pin has an internal 200k ohm pull
down resistor that is enabled by default.
So it is safe to replace 'reset-gpios' with 'shutdown-gpios'.
Fixes: d449121e5e8a ("arm64: dts: rockchip: Add Pine64 PineNote board")
Signed-off-by: Diederik de Haas <didi.debian@xxxxxxxxx>
Link: https://lore.kernel.org/r/20241008113344.23957-5-didi.debian@xxxxxxxxx
Signed-off-by: Heiko Stuebner <heiko@xxxxxxxxx>
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-pinenote.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-pinenote.dtsi
index 42f9507c01da1..27d89f48c42bd 100644
--- a/arch/arm64/boot/dts/rockchip/rk3566-pinenote.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3566-pinenote.dtsi
@@ -685,9 +685,9 @@ bluetooth {
clock-names = "lpo";
device-wakeup-gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>;
host-wakeup-gpios = <&gpio0 RK_PC3 GPIO_ACTIVE_HIGH>;
- reset-gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&bt_enable_h>, <&bt_host_wake_l>, <&bt_wake_h>;
pinctrl-names = "default";
+ shutdown-gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_LOW>;
vbat-supply = <&vcc_wl>;
vddio-supply = <&vcca_1v8_pmu>;
};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3.dtsi
index 45de2630bb503..e9fa9bee995ae 100644
--- a/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3.dtsi
@@ -402,9 +402,9 @@ bluetooth {
clock-names = "lpo";
device-wakeup-gpios = <&gpio2 RK_PB2 GPIO_ACTIVE_HIGH>;
host-wakeup-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_HIGH>;
- reset-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&bt_host_wake_h &bt_reg_on_h &bt_wake_host_h>;
+ shutdown-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_LOW>;
vbat-supply = <&vcc_3v3>;
vddio-supply = <&vcc_1v8>;
};
