From: Miquel Raynal <miquel.raynal@xxxxxxxxxxx>
commit 3a1b777eb9fb75d09c45ae5dd1d007eddcbebf1f upstream.
Until recently the "upper layer" was MTD. But following incremental
reworks to bring spi-nand support and more recently generic ECC support,
there is now an intermediate "generic NAND" layer that also needs to get
access to some values. When using "converted" ECC engines, like the
software ones, these values are already propagated correctly. But
otherwise when using good old raw NAND controller drivers, we need to
manually set these values ourselves at the end of the "scan" operation,
once these values have been negotiated.
Without this propagation, later (generic) checks like the one warning
users that the ECC strength is not high enough might simply no longer
work.
Fixes: 8c126720fe10 ("mtd: rawnand: Use the ECC framework nand_ecc_is_strong_enough() helper")
Cc: stable@xxxxxxxxxxxxxxx
Reported-by: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
Closes: https://lore.kernel.org/all/Zhe2JtvvN1M4Ompw@xxxxxxxxxxxxxx/
Signed-off-by: Miquel Raynal <miquel.raynal@xxxxxxxxxxx>
Tested-by: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
Link: https://lore.kernel.org/linux-mtd/20240507085842.108844-1-miquel.raynal@xxxxxxxxxxx
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
drivers/mtd/nand/raw/nand_base.c | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)
--- a/drivers/mtd/nand/raw/nand_base.c
+++ b/drivers/mtd/nand/raw/nand_base.c
@@ -6301,6 +6301,7 @@ static const struct nand_ops rawnand_ops
static int nand_scan_tail(struct nand_chip *chip)
{
struct mtd_info *mtd = nand_to_mtd(chip);
+ struct nand_device *base = &chip->base;
struct nand_ecc_ctrl *ecc = &chip->ecc;
int ret, i;
@@ -6445,9 +6446,13 @@ static int nand_scan_tail(struct nand_ch
if (!ecc->write_oob_raw)
ecc->write_oob_raw = ecc->write_oob;
- /* propagate ecc info to mtd_info */
+ /* Propagate ECC info to the generic NAND and MTD layers */
mtd->ecc_strength = ecc->strength;
+ if (!base->ecc.ctx.conf.strength)
+ base->ecc.ctx.conf.strength = ecc->strength;
mtd->ecc_step_size = ecc->size;
+ if (!base->ecc.ctx.conf.step_size)
+ base->ecc.ctx.conf.step_size = ecc->size;
/*
* Set the number of read / write steps for one page depending on ECC
@@ -6455,6 +6460,8 @@ static int nand_scan_tail(struct nand_ch
*/
if (!ecc->steps)
ecc->steps = mtd->writesize / ecc->size;
+ if (!base->ecc.ctx.nsteps)
+ base->ecc.ctx.nsteps = ecc->steps;
if (ecc->steps * ecc->size != mtd->writesize) {
WARN(1, "Invalid ECC parameters\n");
ret = -EINVAL;
Patches currently in stable-queue which might be from miquel.raynal@xxxxxxxxxxx are
queue-6.9/mtd-rawnand-fix-the-nand_read_data_op-early-check.patch
queue-6.9/mac802154-fix-time-calculation-in-ieee802154_configu.patch
queue-6.9/mtd-rawnand-bypass-a-couple-of-sanity-checks-during-nand-identification.patch
queue-6.9/mtd-rawnand-ensure-ecc-configuration-is-propagated-to-upper-layers.patch
queue-6.9/mtd-rawnand-rockchip-ensure-nvddr-timings-are-rejected.patch
