This is a note to let you know that I've just added the patch titled
gpiolib: of: fix lookup quirk for MIPS Lantiq
to the 6.6-stable tree which can be found at:
http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary
The filename of the patch is:
gpiolib-of-fix-lookup-quirk-for-mips-lantiq.patch
and it can be found in the queue-6.6 subdirectory.
If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@xxxxxxxxxxxxxxx> know about it.
commit 5128b4508cf8cfc31f848e364b6b3404678b4487
Author: Dmitry Torokhov <dmitry.torokhov@xxxxxxxxx>
Date: Mon Jul 1 10:38:50 2024 -0700
gpiolib: of: fix lookup quirk for MIPS Lantiq
[ Upstream commit 3645ffaf2b334abaf5f53e5ca0f47465d91e69d2 ]
As it turns out, there is a large number of out-of-tree DTSes (in
OpenWrt project) that used to specify incorrect (active high) polarity
for the Lantiq reset GPIO, so to keep compatibility while they are
being updated a quirk for force the polarity low is needed. Luckily
these old DTSes used nonstandard name for the property ("gpio-reset" vs
"reset-gpios") so the quirk will not hurt if there are any new devices
that need inverted polarity as they can specify the right polarity in
their DTS when using the standard "reset-gpios" property.
Additionally the condition to enable the transition from standard to
non-standard reset GPIO property name was inverted and the replacement
name for the property was not correct. Fix this as well.
Fixes: fbbbcd177a27 ("gpiolib: of: add quirk for locating reset lines with legacy bindings")
Fixes: 90c2d2eb7ab5 ("MIPS: pci: lantiq: switch to using gpiod API")
Reported-by: Martin Schiller <ms@xxxxxxxxxx>
Acked-by: Martin Schiller <ms@xxxxxxxxxx>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@xxxxxxxxx>
Link: https://lore.kernel.org/r/ZoLpqv1PN08xHioh@xxxxxxxxxx
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx>
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
diff --git a/drivers/gpio/gpiolib-of.c b/drivers/gpio/gpiolib-of.c
index d9525d95e818d..133d2a4c31a6d 100644
--- a/drivers/gpio/gpiolib-of.c
+++ b/drivers/gpio/gpiolib-of.c
@@ -192,6 +192,16 @@ static void of_gpio_try_fixup_polarity(const struct device_node *np,
*/
{ "himax,hx8357", "gpios-reset", false },
{ "himax,hx8369", "gpios-reset", false },
+#endif
+#if IS_ENABLED(CONFIG_PCI_LANTIQ)
+ /*
+ * According to the PCI specification, the RST# pin is an
+ * active-low signal. However, most of the device trees that
+ * have been widely used for a long time incorrectly describe
+ * reset GPIO as active-high, and were also using wrong name
+ * for the property.
+ */
+ { "lantiq,pci-xway", "gpio-reset", false },
#endif
};
unsigned int i;
@@ -491,9 +501,9 @@ static struct gpio_desc *of_find_gpio_rename(struct device_node *np,
{ "reset", "reset-n-io", "marvell,nfc-uart" },
{ "reset", "reset-n-io", "mrvl,nfc-uart" },
#endif
-#if !IS_ENABLED(CONFIG_PCI_LANTIQ)
+#if IS_ENABLED(CONFIG_PCI_LANTIQ)
/* MIPS Lantiq PCI */
- { "reset", "gpios-reset", "lantiq,pci-xway" },
+ { "reset", "gpio-reset", "lantiq,pci-xway" },
#endif
/*
