From: Gabor Juhos <j4g8y7@xxxxxxxxx> commit 5fce38e2a1a97900989d9fedebcf5a4dacdaee30 upstream. Booting v6.8 results in a hang on various IPQ5018 based boards. Investigating the problem showed that the hang happens when the clk_alpha_pll_stromer_plus_set_rate() function tries to write into the PLL_MODE register of the APSS PLL. Checking the downstream code revealed that it uses [1] stromer specific operations for IPQ5018, whereas in the current code the stromer plus specific operations are used. The ops in the 'ipq_pll_stromer_plus' clock definition can't be changed since that is needed for IPQ5332, so add a new alpha pll clock declaration which uses the correct stromer ops and use this new clock for IPQ5018 to avoid the boot failure. Also, change pll_type in 'ipq5018_pll_data' to CLK_ALPHA_PLL_TYPE_STROMER to better reflect that it is a Stromer PLL and change the apss_ipq_pll_probe() function accordingly. 1. https://git.codelinaro.org/clo/qsdk/oss/kernel/linux-ipq-5.4/-/blob/NHSS.QSDK.12.4/drivers/clk/qcom/apss-ipq5018.c#L67 Cc: stable@xxxxxxxxxxxxxxx Fixes: 50492f929486 ("clk: qcom: apss-ipq-pll: add support for IPQ5018") Signed-off-by: Gabor Juhos <j4g8y7@xxxxxxxxx> Tested-by: Kathiravan Thirumoorthy <quic_kathirav@xxxxxxxxxxx> Reviewed-by: Kathiravan Thirumoorthy <quic_kathirav@xxxxxxxxxxx> Link: https://lore.kernel.org/r/20240315-apss-ipq-pll-ipq5018-hang-v2-1-6fe30ada2009@xxxxxxxxx Signed-off-by: Bjorn Andersson <andersson@xxxxxxxxxx> Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx> --- drivers/clk/qcom/apss-ipq-pll.c | 30 +++++++++++++++++++++++++++--- 1 file changed, 27 insertions(+), 3 deletions(-) --- a/drivers/clk/qcom/apss-ipq-pll.c +++ b/drivers/clk/qcom/apss-ipq-pll.c @@ -55,6 +55,29 @@ static struct clk_alpha_pll ipq_pll_huay }, }; +static struct clk_alpha_pll ipq_pll_stromer = { + .offset = 0x0, + /* + * Reuse CLK_ALPHA_PLL_TYPE_STROMER_PLUS register offsets. + * Although this is a bit confusing, but the offset values + * are correct nevertheless. + */ + .regs = ipq_pll_offsets[CLK_ALPHA_PLL_TYPE_STROMER_PLUS], + .flags = SUPPORTS_DYNAMIC_UPDATE, + .clkr = { + .enable_reg = 0x0, + .enable_mask = BIT(0), + .hw.init = &(const struct clk_init_data) { + .name = "a53pll", + .parent_data = &(const struct clk_parent_data) { + .fw_name = "xo", + }, + .num_parents = 1, + .ops = &clk_alpha_pll_stromer_ops, + }, + }, +}; + static struct clk_alpha_pll ipq_pll_stromer_plus = { .offset = 0x0, .regs = ipq_pll_offsets[CLK_ALPHA_PLL_TYPE_STROMER_PLUS], @@ -145,8 +168,8 @@ struct apss_pll_data { }; static const struct apss_pll_data ipq5018_pll_data = { - .pll_type = CLK_ALPHA_PLL_TYPE_STROMER_PLUS, - .pll = &ipq_pll_stromer_plus, + .pll_type = CLK_ALPHA_PLL_TYPE_STROMER, + .pll = &ipq_pll_stromer, .pll_config = &ipq5018_pll_config, }; @@ -204,7 +227,8 @@ static int apss_ipq_pll_probe(struct pla if (data->pll_type == CLK_ALPHA_PLL_TYPE_HUAYRA) clk_alpha_pll_configure(data->pll, regmap, data->pll_config); - else if (data->pll_type == CLK_ALPHA_PLL_TYPE_STROMER_PLUS) + else if (data->pll_type == CLK_ALPHA_PLL_TYPE_STROMER || + data->pll_type == CLK_ALPHA_PLL_TYPE_STROMER_PLUS) clk_stromer_pll_configure(data->pll, regmap, data->pll_config); ret = devm_clk_register_regmap(dev, &data->pll->clkr); Patches currently in stable-queue which might be from j4g8y7@xxxxxxxxx are queue-6.9/clk-qcom-clk-alpha-pll-fix-rate-setting-for-stromer-plls.patch queue-6.9/clk-qcom-apss-ipq-pll-use-stromer-ops-for-ipq5018-to-fix-boot-failure.patch queue-6.9/firmware-qcom_scm-disable-clocks-if-qcom_scm_bw_enable-fails.patch
